Assa Abloy Yale SIMPLICITY User manual

P/No. YSL-5121 04/18
RIGHT - HAND DOOR LEFT - HAND DOOR
OUTSIDE
DOOR OPENING
IN
OUTSIDE
DOOR OPENING
OUT
OUTSIDE
DOOR OPENING
OUT
OUTSIDE
DOOR OPENING
IN
1
4
2
SETTING LOCK STATUS
SETTING LOCK STATUS
HAND OF DOOR ACCORDING TO ENGLISH PRACTICE
Determine hand of lock required from hand of door chart above.
Yale Simplicity Series Mortice Locks are mounted in accordance
with these instructions. Locks may or may not have cylinders,
lever handles or turn knob. Disregard instructions referring to the
features not required.
Important : Before drilling door, ensure correct hand is being installed.
NOTE: CASE DOES NOT need to be opened, to change HAND or
FUNCTION of LOCK.
HANDING OF LOCK
Determine hand of lock required from above hand of door chart.
Rotate bolt head to suit latching direction. Ensure lock is in UNLOCKED position.
To UNLOCK (if required), using a small screwdriver, lever out Cylinder Hole
Plug where fitted and lift snib using the screwdriver.
SNIB
Rotation of the Snib hands the lock. With snib in unlocked position, use a
cylinder pin to rotate the snib if required.
ESCAPE Locks
The hole on the snib indicates the side lockable.
For left hand door the hole will be visible from the left of the lock.
For right hand door the hole will be visible from the back of the lock.
The escape side will have no holes on the snib.
Establish which side the adaptor is to be located, lever out Cylinder hole plug
where fitted.
PUT LOCK IN LOCKED POSITION, as shown in Step 1.
Insert Adaptor into lock body with TOP of Turn Knob Cam point away from front
of lock body. Ensure Turn Knob Cam is engaged in yoke of snib as shown.
Place retainer pin through front plate to retain adaptor to lock. Ensure pin is
flush with front plate
LOCKABLE
LOCKABLE
ESCAPE
ESCAPE LEFT HAND DOOR
ESCAPE
TURN KNOB ADAPTORS
UNLOCKED
(Snib up)
LOCKED
(Snib down)
Yale®
MOUNTING INSTRUCTIONS
SIMPLICITY MORTICE LOCK
ESCAPE RIGHT HAND DOOR
STANDARD TURN KNOB ADAPTORS
3 ANTI-LOCKOUT TURN KNOB ADAPTORS 4
Establish which side the adaptor is to be located, lever out Cylinder hole plug
where fitted.
PUT LOCK IN LOCKED POSITION, as shown in Step 1.
Align Adaptor cam so that it points up towards the top of the lock front plat, and
Place retainer pin through front plate to retain adaptor to lock. Ensure pin is
flush with front plate.
L
L
YOKE
TURN KNOB CAM
Anti-lockout is achievable via an anti-lockout adaptor. Ensure the lock is
unlocked and that the leg of the adaptor is installed behind the bolt frame.
The adaptors are handed. Ensure that the correct adaptor is installed.
1 HOLE - 20mm DIA. FOR SPINDLE
1 HOLE - 20mm DIA. FOR SPINDLE
2 HOLES - 20mm DIA. SLOT FOR CYLINDER
2 HOLES - 20mm DIA. SLOT FOR CYLINDER
2 HOLES - Ø6.5mm
2 HOLES - Ø6.5mm
ENSURE LOCK IS REMOVED FROM MORTICE
BEFORE DRILLING HOLES.
TO PREVENT POSSIBLE DAMAGE TO DOOR FACE
DO NOT DRILL RIGHT THROUGH DOOR.
ENSURE LOCK IS REMOVED FROM MORTICE
BEFORE DRILLING HOLES.
TO PREVENT POSSIBLE DAMAGE TO DOOR FACE
DO NOT DRILL RIGHT THROUGH DOOR.
Adaptor leg
insert into the lock. (Look from the other side to check engagement with snib)
1 HOLE - 20mm DIA.
FOR TURN
1 HOLE - 20mm DIA.
FOR TURN

65 DOOR PREPARATION DOOR PREPARATION
Establish height that lockset will be mounted on door and mark centreline of
door thickness on door edge.
Place Mortice Template on door and align centreline on template with centreline
on door.
Mark and drill mortice to suit mortice lock depth (90mm).
Ease out mortice cavity where necessary. Clean out mortice before inserting lock.
Insert lock in mortice with Cover Plate on and scribe around Cover Plate for size of
recess, ensuring that no foreign matter finds it way into the lock mechanism.
Remove lock from mortice and chisel recess 4mm deep to receive both front
and cover plate. Cover plate must be flush with edge of door.
Ensure lock is removed from mortice cavity. Fold template along backset fold
line. Align EDGE A with bottom of cover plate recess. Establish holes required to
suit lock function, mark hole centres accurately, drill and clean holes.
Drill furniture holes as required.
Fasten mortice lock into door using mounting screws provided.
87
Place lock in mortice and insert cylinder.
Secure cylinder with retainer pin, ensuring pin is flush with front plate.
Install Cover plate and secure with 2 M4 screws provided to lock body.
Strike
Strike
Box
Jamb
Mark out door frame for strike.
Use strike and strike box as templates and then mortice door frame for strike.
Screw strike and strike box to the door frame with two screws supplied with
Spindles are supplied with the furniture.
Insert spindle(s) into lock, as required.
Assemble furniture as required. Ensure furniture is not over-tightened.
LOCKS WITH TURNKNOBS
9LOCKS WITH SPINDLES 10 MOUNTING STRIKE
ENSURE LOCK IS REMOVED FROM MORTICE
HOLE
22mm DIA
FOR SPINDLE
EDGE A
2 HOLES
20mm DIA
FOR CYLINDER
60 mm Backset
Centreline
Mortice template
Door
T
ESK
CABmm06
R
OODF
O
EGDE
GNOL
A
EN
I
LDLOF
ecitro
M
enile
rtn
e
C
IMPORTANT - To prevent damage to the door face from
drill "breakthrough", MARK BOTH SIDES OF DOOR &
DRILL HOLES HALF WAY THROUGH EACH SIDE
LATCHNG OR LOCKING TURNKNOB
IMPORTANT :
Attach spindle spring to rear
of spindle before assembling
Cover
plate
Cover plate
LOCKS AND CYLINDERS
Cylinder
retainer
pin
Cylinder
assembly
LATCH BOLT
CENTRE LINE
Timber frames - drill 2.5mm pilot holes and use 30mm long screws
Metal frames - drill 4mm pilot holes and use 12mm long screws
Mark correct length of connecting bar as shown.
For locking turnknob, mark the connecting bar at the edge of the screw on the
mounting lock faceplate.
Cut connecting bar to length, remembering to remove the burr.
When lockset is in unlocked condition, turnknob to be vertical.
Screw position
Anti-rattle tab
P
L
E
A
S
E
R
E
C
Y
C
L
E
T
H
I
S
P
A
C
K
A
G
I
N
G
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 ©2018
The global leader in door opening solutions
To eliminate the rattle between the door and plate, bend the tab by small increments.