Wittkopp Primor 1600 User guide

Primor 1600
Installer manual
Installation and commissioning instructions
en_02 P1600-Part 2b-Installer manual V1.00
1 / 5
Note:
On the cover sheet you can find warning information, and an explanation of the symbols and
terms used, together with the exclusion of liability.
Contents
General................................................................................................................................. 2
Preparation for installation..................................................................................................... 3
Installation dimensions for lock 1600................................................................................. 3
Preparation of the boltwork / door...................................................................................... 3
Installation............................................................................................................................. 4
Wiring / installation................................................................................................................ 4
Function test.......................................................................................................................... 5
Input of the opening code.................................................................................................. 5
Keypad test ....................................................................................................................... 5
Mount the keypad before installing the electronic lock. All the keypads of the Primor series
can be used. For information on how to install the keypads, please refer to "Part 2a- Primor
keypad installer manual".

Primor 1600
Installer manual
Installation and commissioning instructions
en_02 P1600-Part 2b-Installer manual V1.00
2 / 5
General
P1600 series locks have standard
installation dimensions and can be installed
in all 4 installation positions (right, left, top,
bottom). They are designed for boltworks
with a one-sided locking edge, i.e. only for
force absorption by the straight boltwork
flank of the quarter-circle-shaped bolt.
They are intended to be installed in safes
made of metal.
The electronic lock requires no
maintenance in a normal residential or
office environment. We recommend a
security and function test of the electronic
lock after around 10,000 closings.
It is essential that the lock is protected
against attacks from outside. We
recommend that you protect against access
the security-relevant parts of the high-
security lock also when the door of the
container that holds the valuables is open.
It is not permissible to use two locks of the
same type in connection with analogue
keypads without any additional
components for locking state detection.
Do not apply any lubricants or other
substances to the lock.
Always use the following sequence for installation:
•Check the preconditions for installation
•Wiring / installation of the cables
•Set up the power supply
•Function test of the locking mechanism
•Perform all settings (user installation, delay time)
Ensure that the load limits are not exceeded at any time.
You can find the corresponding values in Annex C "Technical data".

Primor 1600
Installer manual
Installation and commissioning instructions
en_02 P1600-Part 2b-Installer manual V1.00
3 / 5
Preparation for installation
Installation dimensions for lock 1600
Preparation of the boltwork / door
To install the lock, there must be three
threaded holes for fastening on the
boltwork or inside the safe door. The
electronic lock must be fastened with the
supplied screws or M6 or 1/4” cylinder
screws (min. strength class 8.8). The screw
length should be measured so that a
minimum screw-in depth of 6 mm is
possible.
Drilling pattern:
The electronic lock can be installed in the area of openings with a maximum diameter of 11.5
mm around the axis centre shown above.
This hole is not required on Primor 1000 / 1600 / 2000.
Primor 100 / 2000: Centre of electronic lock drive is flush with centre of
input unit (Primor RO)/centre of keypad lever (Primor RE)

Primor 1600
Installer manual
Installation and commissioning instructions
en_02 P1600-Part 2b-Installer manual V1.00
4 / 5
Installation
The retaining screws must be tightened in
such a way that a permanent and firm hold
is ensured.
Tighten the fastening screws with a
maximum torque of 6 Nm. To prevent the
screws from becoming loose, the screws
must be secured using safety washers or
using screw locking agents.
There must be no tension or pressure on
the lock bolt after installation.
Make sure there is sufficient clearance to
the locking point.
Wiring / installation
Cut off the power supply / battery, before starting any work or making any changes to the
wiring between the lock and keypad.
Lock cable entry
Plug
Connecting cable

Primor 1600
Installer manual
Installation and commissioning instructions
en_02 P1600-Part 2b-Installer manual V1.00
5 / 5
Function test
Carry out a function test after completing all
the mounting and installation work.With the
door open, you should open and close the
lock several times using the master code
that had been set at the factory.
The relationship between easy opening and
reliable closing can be set via the operating
lever of the boltwork.
The locking check can be done via the
operating lever of the boltwork and should
be performed after each closing and
locking.
Input of the opening code
e.g. master factory code


=✓
→

The opening code can be input
directly as described above, without
selection. The bolt is released for
approx. 3 seconds after a valid
code has been entered. Open the
container with the valuables within
this time after inputting the code.
=

Keypad test
We recommend a final keypad test using function menu 5 to ensure that all the numeric keys
function properly.
 ☼Checking the menu system
Press the keys in the
sequence
…

=✓
Press each numeric key once. A
functional key is indicated by a
double signal tone.
A key that is not recognised is
indicated by a long signal tone and
the function test is terminated. The
system must be checked.