Kyla Smart Door Lock User manual
Installation Guide
01
M5 Screw 8×8 Handle Shaft 5×5 ShaftScrew Cover Spring
×2
×2
×2 ×1 ×1
×2
×2
×2
1.5 Spanner
4.0 Spanner3.0 Spanner
Lock Body
×1 ×1
×10
Strike Plate
M5×10
Battery
×10
Key
×2
Drilling Template
×1
Manual
×2
Back Panel Front Panel
×1 ×1
×1
×1 ×1
47 57 67
×2
42
45
65 68
40
Smart Door Lock
User Guide
1. Product List (security door)
02
2. Product List (wooden door)
M5 Screw 8×8 Handle Shaft 5×5 Shaft
Screw Cover Spring
×2 ×2
×2
×2 ×1 ×1
×2
×2
×2
1.5 Spanner 4.0 Spanner3.0 Spanner Battery
×10
Key
×2
Drilling Template
×1
Manual
×2
Back Panel Front Panel
×1 ×1
×1 ×1 ×1
45 47 57 67 68
42
65
40
Lock Body
×1 ×1 ×1
Strike Plate Strike Box
×8 ×2
M4×45M4×45
Smart Door Lock
User Guide
03
3. Installation Note
1. Check the products and accessories according to the product list.
2. Check the specifications of the products.
3. Check the accessories package to see whether the guide plate and
strike plate are matched with your door.
4. Before installation, connect the front panel, back panel and lock body,
then power on to check whether the password and fingerprint work
normally.
5. Do not close the door during installation.
6. After installation, insert the key while debugging to avoid the failed unlock
caused by accident.
7. After installation, check according to the acceptance criteria.
If you have any questions or difficulties, contact your vendor for technical
support.
Door Thickness and Matched Accessories
50≤TH≤70
Screw coverThickness M5 screw
L=45，2pcs L=42，2pcs
8 X 8
Square shaft 5 X 5
Square shaft
L=47，2pcs
L=57，1pcs L=40，2pcs
70≤TH≤90 L=65，2pcs L=42，2pcs L=47，1pcs
L=67，1pcs L=68，2pcs
Standard Door Thickness: 50~90mm
Custom accessories needed if the door thickness is beyond the range of the
standard.
04
4. Conrm the Drilling on the Door
Confirm whether the drilling is matched with the drilling drawing, if not,
please redrill according to the drawing. Do not close the door before the
complete installation.
Guide plate drilling drawing
Drilling Drawing
05
5. Guide Plate Replacement
1. Open the deadbolt, take off the screws and the guide plate.
2. Replace the guide plate.
3. Screw on and reset the deadbolt.
12
1 2 3
06
6. Open Direction Changing in the Lock Body
Initial open direction: Right outward. After changing the direction, screw
on the hex screw and ensure that the screw top faces indoor.
Change the direction of the oblique deadbolt
1. Push the reversing piece upwards
2. Push the oblique deadbolt in
3. Turn the oblique deadbolt then release it
4. Release the reversing piece
Change the direction of the clutch
1. Put the clutch screw towards indoor: Change the direction of the reversing
clutch screw towards indoor by the hexagon spanner.
Notes: Pay attention not to drop the screws into the lock body.
180°
1
2
3
4
2X
2X
2X
2X
07
7. Direction Changing of the Handle
Below is the direction changing illustration of the handle of the front
panel. For the handle of back panel, please refer to this.
08
8. Front and Back Panel Accessories Installation
Respectively install the screw cover, handle shaft spring, thumb-latch shaft
and key shaft.
Notes: Screw on tightly after adjusting the thumb-latch shaft and key shaft.
2X
2X
09
9. Lock Body Installation
Upside-down triangle
10
10. 8 X 8 Handle Shaft Installation
Adjust the hole direction of the lock body shaft during the installation.
11
11. Install the Front Panel
Infix the lock body cable and install the front panel.
Notes: Do not insert the key.
2X
12
12. Wiring of the Back Panel
Pay attention to the wire direction.
2X
13
13. Install the Back Panel and Screws
Arrange the cables to avoid interference.
M5 Screw
M5 Screw
Insert the cable
in the hole
Aline the thumb-latch
vertically
14
14. Install the Battery Cover and Insert Batteries
15. Strike Plate & Strike Box Installation
15
16
16. Installation Acceptance
∥
∥
∥
17
17. Installation Acceptance Criteria
1. Turn the front handle and back handle smoothly with normal springback.
2. Turn the front handle and back handle to enable the square deadbolt.
3. The front panel and back panel are parallel with the door frame.
4. Key is available to unlock.
5. The oblique deadbolt is open when closed the door.
6. Turn the thumb-latch to enable the back locking deadbolt.
7. The door is not waggling when the deadbolts are open.
8. Ensure that the fingerprint and password work well after power on.
Notes: During the procedure of acceptance, please insert the key to avoid
the failed unlock caused by accident.
31 Ubi Road 1, #01-05, Singapore 408694
Contact Us
Aztech Technologies Pte Ltd.
18
©2018 Aztech Technologies Pte Ltd. All rights reserved.
