Fotric 320 Series Instruction manual

Fotric 320M/320F Series

Contents
Legal Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information . . . . . . . . . . . . . . . . . . . . . . 5
Thermal Imager . . . . . . . . . . . . . . . . . . . . . . . . . 8
Interface Introduction . . . . . . . . . . . . . . . . . . 12
Quick-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1
1.1 Legal Disclaimer
Uncooled thermal imager manufactured by FOTRIC are
entitled to 1 to 2 years warranty service (depending on
the speci󽗉c model) from the date of initial purchase and
delivery. Warranty covers defects caused by materials and
production processes, provided that such products are
handled under normal storage, use, and repair conditions
and in accordance with FOTRIC instructions.
Products not manufactured by FOTRIC but included in
the system that FOTRIC sells to the original purchaser are
covered by the speci󽗉c supplier's warranty terms (if any)
and FOTRIC is not liable for those products. This warranty is
provided to the original purchaser and is not transferable.
This warranty does not apply to any product that has
been damaged by misuse, neglect, accident, or abnormal
operating conditions. Consumable parts are not covered by
this warranty.
Any defects in the products covered by this warranty must
be reported and the product must not be used after, to
prevent further damage. The purchaser must report any
defects to FOTRIC immediately, otherwise this warranty will
not apply.
If the product is proven defective in relation to materials
or manufacturing after FOTRIC's inspection, it is up to
the user whether it is to be repaired or replaced (refer
to FOTRIC warranty policy), provided that the product
must be returned to FOTRIC within 3 Months from above
Legal Disclaimer

2
mentioned report date. FOTRIC has no obligation or liability
for any defects other than those mentioned above. This
product is exempt from any other warranties, expressed or
implied. FOTRIC hereby disclaims any implied warranties of
merchantability and applicability for a particular purpose.
FOTRIC is not responsible for any direct, indirect, special,
incidental or consequential loss or damage based on
contract, civil, or any other legal theory. This warranty
clause shall apply the relevant provisions of the laws of the
People's Republic of China. Any dispute or claim arising out
of or relate to this warranty shall be 󽗉nally settled through
arbitration in accordance with the rules of the Shanghai
Pudong New District People's Court of the People's Republic
of China. The place of arbitration shall be Shanghai.
1.2 Usage Statistics
FOTRIC reserves the right to collect anonymous usage
statistics to help maintain and improve the quality of the
products and services provided.
Legal Disclaimer

3
1.3 Copyright
No parts of this software (including source code) may be
reproduced, transmitted, transcribed, or translated into
any kind of language or computer language in any form or
by electronic, electromagnetic, optical, manual ways, or
any other means without the prior written permission of
FOTRIC.
No parts of this document may be reproduced,
photocopied, reprinted, translated, or transmitted to any
readable electronic medium or machine without the prior
written consent of FOTRIC.
The names and logos shown on the products herein are
either registered trademarks or trademarks of FOTRIC
and/or its a󽗋liates. All other trademarks, trade names or
company names referenced herein are for identi󽗉cation
purposes only and are the property of respective owners.
1.4 Quality Assurance
The quality management system for the development and
production of these products in FOTRIC has been certi󽗉ed
in accordance with the ISO 9001 standard.
FOTRIC is committed to a policy of continuous
development, as we reserve the right to modify or upgrade
any product without prior notice.
Legal Disclaimer

4
1.5 Export Control
Thermal imaging products are listed as export-controlled
products by U.S. Department of Commerce, United Nations
Security Council (UNSC), and European Union (EU). This
product contains a focal plane array and cannot be used in
controlled countries (such as North Korea, Iran, Syria, Cuba,
Sudan, Russia, etc.). Please do not bring this product into
or used in controlled countries. Any loss or liability arising
from the above actions will be borne by the purchaser.
Legal Disclaimer

5
This product complies with the restrictions for Class A
digital equipment in Chapter 15 of the FCC Rules. These
restrictions are designed to prevent harmful interference
to civilian installations. If not installed and used in strict
accordance with the instructions , this device will generate,
use and emit radio frequency energy, which may cause
harmful interference to radio communications.
De󽗉nition
! Warning> Represents a hazardous situation or behavior
that could result in personal injury or death.
! Caution > Represents conditions or actions that could
result in damage to the device or permanent loss of data.
! Notice> Represents useful information for users.
Please read before using:
! Warning > This is class A product. In a domestic
environment, this product may cause radio interference
in which cause the user may be required to take adequate
measures.
! Warning > Do not disassemble or do modi󽗉cations to
the battery of the thermal imager . The battery contains
safety and protection devices, which, if damage occurs, can
cause the battery to become hot, or cause an explosion or
an ignition. If there is a leak from the battery and you get
Safety Information

6
the 󽗊uid in your eyes, do not rub your eyes. Flush well with
water and immediately get medical care. The battery 󽗊uid
can cause injury to your eyes if you do not do this.
! Warning > The thermal imager is equipped with a laser
pointer. Do not look directly into the laser beam. The laser
beam can cause eye irritation.
!Caution> The thermal imager uses a very sensitive
thermal sensor, so do not point the infrared camera (with
or without the lens cover) at strong energy sources, for
example, devices that cause laser radiation, or the sun. This
can have an unwanted e󽗈ect on the accuracy of the camera.
It can also cause damage to the detector in the camera
which is not covered in Fotric's warranty.
!Caution> Original packing box must be used during
transportation.Please do not strongly hit the thermal
imager during use and transportation.
! Caution > When storing the thermal imager, it is
recommended to use the original packing box and place it
in a cool and dry place, away from strong electromagnetic
󽗉eld.
!Caution> Please avoid oil and various chemical
substances to contaminate or damage the surface of the
lens. Please cover the lens with cap when not use.
!Caution> Do not use the camera in temperatures
higher than +50° C (+122° F), unless other information is
speci󽗉ed in the user documentation or technical data. High
temperatures can cause damage to the camera.
!Caution> In order to prevent potential risk of data loss,
please copy (back up) the data to a computer or server
Safety Information

7
periodically.
! Caution > Please do not open the thermal imager' s shell
or modify it without permission. Repair services can only be
performed by authorized FOTRIC personnel.
! Notice> After the thermal imager is turned on, it may
take about 10~15 minutes to warm up before accurate
measurement.
!Notice> Every thermal imager's temperature correction
has been performed before delivered from factory.
Safety Information

8
Front View
Thermal Imager