FoxAlien 3018-SE User manual

3018-SE CNC ROUTER
USER MANUAL

●I. Hardware Assembly
●Part-1 Gantry Assembly ------------------------ 1
●Part-2 Control Board Assembly ------------------------ 3
●Part-3 Wiring Diagram ------------------------ 4
●Part-4 Case Assembly-Left Panel ----------------------- 7
●Part-5 Magnet Suction Block Assembly ----------------------- 8
●Part-6 Case Assembly-Right Panel -------------------- 9
●Part-7 Emergency Stop Switch Assembly-----------------------10
●Part-8 Cooling Fan Assembly ----------------------11
●Part-9 Case Assembly- Back Panel -----------------------12
●Part-10 Corner Connector Assembly ----------------------- 14
●Part-11 Case Assembly-Front Panel ----------------------15
●Part-12 Case Assembly- Top Panel ---------------------- 17
●II. Software & Debugging
●Part-1 Driver Installation ------------------------------------- 19
●Part-2 Debugging ------------------------------------- 20
●Part-3 How to Use Z-Probe ------------------------------------- 23
●III. Warranty Terms ------------------------------------- 25
Catalog

-1-
Part
-1 GantryAssembly
Required
Parts
No. Name QTY Picture
(1)
X
-axis Gantry & Spindle 1
(2)
Y
-axis Base 1
(14)
M5*1
4 Bolt 8
(18)
Φ5
Gasket 8
(19)
Elastic Nut
8
Step 1: Place the elastic nuts into the aluminum profiles, adjust the position. And then fix the gantry
right next to the pads on the base with M5*14 bolts and gaskets.
I. Hardware Assembly
Lean the elastic nut to insert into
the profile, then it will be fixed

-2-
Part
-1 GantryAssembly
I. Hardware Assembly
Step 2: Fix the gantry right next to the pads on the base with M5*14 bolts and gaskets.

-3-
Part
-2 Control Board Assembly
Required
Parts
No. Name QTY Picture
(4)
Control board
1
Step 1: Assemble the control board to the back of the machine, right next to the side panel. First
loosen the T-nuts, insert them to the aluminum profile, and then tighten the screws.
I. Hardware Assembly

-4-
Part
-3 Wiring Diagram
I. Hardware Assembly
Brown wire
connects to
the port next
to the red dot.
12V Fan E-stop Z ProbeX
Limit
Switch
Y
Limit
Switch
Z
Limit
Switch
Power
Indicator
USB
Indicator
12V 5A
Power
Supply
Power
on/off
USB Port
12V
Laser X-axis Y-axis Z-axis

-5-
I. Hardware Assembly

-6-
I. Hardware Assembly

-7-
Part
-4 Case Assembly-Left Panel
Required Parts
No. Name QTY Picture
(5)
Left Acrylic Sheet
1
(17)
M5*10 Modified Truss Screw
2
Step 1:
Use M5*10 Modified Truss Screws to fix the left acrylic sheet to the transparent pads which
are pre
-installed on the base.
I. Hardware Assembly

-8-
Part
-5 Magnet Suction Block Assembly
Required
Parts
No. Name QTY Picture
(11)
Corner Connector
1
(17)
M5*10 Modified Truss Screw
1
Step 1: Fix the magnet suction block to the left panel with M5*10 Modified Truss Screw.
I. Hardware Assembly

-9-
Part
-6 Case Assembly-Right Panel
Required
Parts
No. Name QTY Picture
(6)
Right Acrylic Sheet
1
(17)
M5*10 Modified Truss Screw
2
Step 1: Use M5*10 Modified Truss Screws to fix the right acrylic sheet to the transparent pads which
are pre-installed on the base.
I. Hardware Assembly

-10-
Part
-7 Emergency Stop Switch Assembly
Required
Parts
No. Name QTY Picture
(12)
Emergency Stop Switch
1
Step 1:
As following picture, first to loosen the gasket and the nut from the emergency stop switch, and
then put it through the acrylic sheet, and fasten the gasket and nut again.
I. Hardware Assembly

-11-
Part
-8 Cooling Fan Assembly
Required
Parts
No. Name QTY Picture
(13)
Cooling Fan
1
(7)
Back Acrylic Sheet
1
(15)
M3*16 Truss Head Bolt
4
Step 1: Use 4pcs M3*16 Truss Head Bolt to fix the cooling fan to the back acrylic sheet.
I. Hardware Assembly

-12-
Part
-9 Case Assembly- Back Panel
Required
Parts
No. Name QTY Picture
(7)
Back Acrylic Sheet
1
(17)
M5*10 Modified Truss Screw
2
Step 1:
First, wire the fan to the mainboard; and then use M5*10 Modified Truss Screws to fix the back
acrylic sheet to the transparent pads.
I. Hardware Assembly

Step 2: Finished.
I. Hardware Assembly
-13-

-14-
Part
-10 Corner ConnectorAssembly
Required
Parts
No. Name QTY Picture
(11)
Corner Connector
2
(17)
M5*10 Modified Truss Screw
4
Step 1:
Put the corner connector inside the case, fix it with M5*10 Modified Truss Screw from outside.
I. Hardware Assembly

-15-
Part
-11 Case Assembly-Front Panel
Required
Parts
No. Name QTY Picture
(9)
Front Acrylic Sheet &
Door
Handle
1
(16)
M4*8 Flat Head Screw
4
(10)
Corner Connector
1
(17)
M5*10 Modified Truss Screw
3
Step 1: Use M5*10 Modified Truss Screws to fix the corner connector to right acrylic sheet.
I. Hardware Assembly

-16-
Part
-11 Case Assembly-Front Panel
Step 2: Fix the front side acrylic sheet to the hinges with M4*8 Flat Head Screw.
I. Hardware Assembly

-17-
Part
-12 Case Assembly- Top Panel
Required
Parts
No. Name QTY Picture
(8)
TopAcrylic Sheet
1
(11)
Corner Connector
4
(17)
M5*10 Modified Truss Screw
8
Step 1: Fix the 4pcs corner connectors to the sides panels, adjust their position to make sure they are
leveled.
I. Hardware Assembly

-18-
Step 2: Put the top panel above the connectors and fix it with M5*10 modified truss screw.
I. Hardware Assembly