Foxfury Lighting Solutions Taker B70 User manual

PRODUCT MANUAL
480-600
TAKER B70

TABLE OF CONTENTS
INTRODUCTION
Taker B70 Reference Guide 3
Physical Characteristics & Warnings 4
BATTERY
Battery Installation and Replacement 5
Battery Life 6
OPERATION
Operational Modes 6
FEATURES
Ambidextrous Light Activation 7
Pressure Switch 7
Individual LED Rows 8
Dual Settings 8
INSTALLATION
Shield Installation 9
Wiring Installation 10-11
WARRANTY 12–13
CONTACT FOXFURY 13

3
TAKER B70 REFERENCE GUIDE
SHIELD LIGHT
(WITH PROTECTIVE COVER ON)
SHIELD LIGHT
(WITH PROTECTIVE COVER OFF)
+ +
– –
+ +
– –
HANDLE
(BACK SIDE)
PROTECTIVE
COVER
LEDs (6)
PROTECTIVE
LENS (2)
WIRE
HOLES
(4)
TERMINAL
BLOCKS (4)
POWER/MODE
SWITCH (2)
BOLT HOLE (2)
BATTERY
DOOR (2) GRIP
SCREWS (10)
BOLT
HOLE (2)
WIRE
THROUGH
HOLES (4)

4
PHYSICAL CHARACTERISTICS
Please read below before using the Taker B70 as it relays beneficial operating
and safety information.
SHIELD LIGHT (P/N 600-480-300)
DIMENSIONS (WxH) 6.3 x 2.5 in (160 x 2.5 mm)
WEIGHT 35.2 oz (998 g)
HANDLE ONLY (P/N 60-601)
DIMENSIONS (WxH) 5.5 x 4.3 in (127 x 109 mm)
WEIGHT 19.2 oz (554 g) with batteries
WARNINGS
Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft (.06 m)).
FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.
Do NOT attempt to charge the batteries by using the Pressure Switch
Port.
!
!
!
INCLUDED
Handle with Electronics & Pressure Switch (P/N 60-601)
Dual Discover Shield Light Head (P/N 600-480-600)

5
BATTERY INSTALLATION AND REPLACEMENT
1. Twist the Battery Door (at both ends of the handle) in a counter-clockwise
direction to remove them.
2. Insert three (3) batteries (with the negative end first) into either side of the
handle (respect appropriate polarity when installing).
If installing six (6) batteries (doubling battery life), then repeat step 2
one more time on the opposite side of the handle.
3. Re-install the End Cap(s) by twisting in a clockwise direction (make sure
the End Cap(s) are tightly sealed).
Test the light’s performance and function by activating the Power/
Mode Switch (located under the Grip).
BATTERIES
The Taker B70 uses three (3) or six (6) CR123 batteries. As long as there
are at least three (3) installed, the light will function.
Using three (3) CR123 batteries decreases the battery life by half, but
does not effect the light intensity.
Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.
1
2
1
2
3
3
+– +– +– +– +– +–

6
OPERATIONAL MODES
BATTERY LIFE
MODE BATTERY LIFE LUMENS
MOMENTARY 2 hours 1200
CONTINUOUS ON 2 hours 1200
TURBO-STROBE™ 4 hours 1200
*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.
For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the light will operate continuously. When the user
removes pressure from the Switch, the light will turn OFF.
For CONTINUOUS ON mode: Press the Power/Mode Switch two (2)
times in rapid succession. The light will remain ON.
For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in
rapid succession.
For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.
NOTE: The light does not retain the mode in memory. Once you turn the light
ON, you will have to re-select the mode you desire.

7
FEATURES
AMBIDEXTROUS LIGHT ACTIVATION
The Taker B70 includes two (2) Power/Mode Switches on both the left and
right sides of the Handle. This allows users to toggle between modes using
either hand.
PRESSURE SWITCH (INCLUDED)
The Taker B70 includes a Pressure Switch that allows the user to place
it anywhere on the shield. This makes it easier to access the Power/Mode
Switch. The Pressure Switch can easily be attached to the shield or Handle via
Velcro®or glue.
POWER/MODE
SWITCH
POWER/MODE
SWITCH
PRESSURE
SWITCH PORT
PRESSURE SWITCH
HANDLE
(BACK SIDE)
HANDLE
(FRONT SIDE)

8
FEATURES (CONT’D)
INDIVIDUAL LED ROWS
The LEDs of the B70 operate on separate circuits, allowing a single row of
LEDs to continue functioning if the other row is damaged.
DUAL SETTINGS
The Taker B70 includes two mode settings: the ON/OFF SETTING and the
TACTICAL SETTING. The ON/OFF SETTING simply allows the Light Head to
turn ON and OFF. The TACTICAL SETTING allows you to choose from three
(3) different Operational Modes: Momentary, Continuous On, and
Turbo-Strobe™. The Taker B70 is shipped in the TACTICAL SETTING.
To change from the TACTICAL SETTING to the ON/OFF SETTING:
With the light turned OFF, press the Power/Mode Switch twice in rapid
succession and hold for 10 seconds. The light should begin to flash. Once
it begins flashing, it is now in the ON/OFF SETTING.
To change from the ON/OFF SETTING to the TACTICAL SETTING:
With the light turned OFF, press and hold the Power/Mode Switch for 10
seconds. The light should begin to go through a slow Turbo-Strobe™ cycle
and then turn OFF. It is now in the TACTICAL SETTING.

9
SHIELD INSTALLATION
1. Begin by drilling two holes into the shield. To do this, locate the Bolt Hole(s)
(2) located on the BACK SIDE of the Handle (shown above).
HELPFUL TIP: Use a #2 pencil (or a tool of the same diameter) and
insert it through the Bolt Holes (of the BACK SIDE of the Handle)
to draw two marks on the shield. This will help when determining
placement of the holes when drilling.
IMPORTANT: The bolts pictured above are NOT included. The user must
purchase two (2) bolts with the following specifications:
Bolt Head Diameter: 24 mm MAXIMUM
Bolt Shaft Diameter: 7.5 mm MAXIMUM
Bolt Length: 97 mm (this does NOT include the thickness of the shield)
2. Once both holes are drilled through the shield, it is important to drill two
small holes (4 mm diameter) next to each Bolt Hole, so that the wires can
be fed through the shield. NOTE: See pg. 10–11 for wiring installation.
PROTECTIVE COVER
BOLTS (2)
(NOT INCLUDED)
BOLT
HOLES
BALLISTIC SHIELD
Place the shield in
between the Handle
and Light Head.
(The shield pictured is cut in
half for this visual)
LIGHT HEAD
HANDLE
HANDLE
(BACK SIDE)
1
2
The B70 is intended to be installed as an OEM product, by ballistic shield and
armor manufacturers.

10
+ +
– –
+ +
– –
WIRING INSTALLATION
1 2
3
5
4
TERMINAL BLOCK SCREWS
WIRE
THROUGH
HOLES (4)
TERMINAL
BLOCK
HOLDER
SCREWS
(10)
RED WIRE
HOLE
BLACK WIRE
HOLE