Foxfury Lighting Solutions Taker B10 User manual

PRODUCT MANUAL
940K-010S
TAKER B10

TABLE OF CONTENTS
INTRODUCTION
Taker B10 Reference Guide 3
Physical Characteristics & Warnings 4
BATTERY
Battery Installation and Replacement 5
Battery Life 5
OPERATION
Operational Modes 6
ASSEMBLY
Assembling Mount to Clamp 6
Inserting/Removing from the Holder 7
FEATURES
Pressure Switch 8
Tilt 8
Multiple Lights on One Shield 8
INSTALLATION
Shield Installation 9
WARRANTY 10–11
CONTACT FOXFURY 11

3
TAKER B10 REFERENCE GUIDE
LANYARD
HOLE
RUBBER
SLEEVE
POWER/MODE SWITCHLOCKING GROOVE
STRIKE BEZEL
ANTI-ROLL HEAD TAILCAP
HANDLE
ASSEMBLED B10
(WITHOUT FLASHLIGHT)
PICATINNY C-CLAMP
RELEASE
LEVER
PICATINNY
C-CLAMP
FRONT
THUMBSCREW
PICATINNY
RAIL
TILT
ADJUSTMENT
SCREW
CLAMP
MOUNT
SCREWS
(4)
PICATINNY MOUNT
MOUNT
MOUNT
SCREWS (4) HOLDER
HOLDER
SIDESLIDE FLASHLIGHT
(P/N 940-010FI)

4
PHYSICAL CHARACTERISTICS
Please read below before using your Taker B10 as it relays beneficial
operating and safety information.
B10 FULL ASSEMBLY (WITH FLASHLIGHT) (P/N 940 K– 010S)
DIMENSIONS 4.7 x 1.5 x 5.5 in (119 x 38 x 140 mm)
WEIGHT 12.7 oz (360 g) (with no battery)
PICATINNY C-CLAMP (80-013)
DIMENSIONS 2.91 x 1.4 x 1.75 in (74 x 36 x 44 mm)
WEIGHT 4.9 oz (139 g)
WARNINGS
Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft (.06 m)).
FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.
!
!
INCLUDED
SideSlide Picatinny Flashlight (P/N 940K-010PIC)
Picatinny C-Clamp (85-013)

5
BATTERIES
The Taker B10 flashlight requires one (1) 18650 battery or two (2)
CR123 batteries.
Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.
BATTERY INSTALLATION AND REPLACEMENT
1. Twist the Tailcap in a counter-clockwise direction to remove it.
2. Insert the battery with the positive end first. (Respect appropriate polarity
when installing).
3. Reinstall the Tailcap by twisting it in a clockwise direction back onto the
Handle. (Make sure the Tailcap is tightly sealed).
4. Test the light’s performance and function by activating the Power/Mode
Switch (located at the end of the Tailcap).
BATTERY LIFE
MODE BATTERY LIFE LUMENS
MOMENTARY 1.5 hours 380
CONTINUOUS HIGH 1.5 hours 380
CONTINUOUS LOW 10 hours 70
TURBO-STROBE™4 hours 380
*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.
+BATTERY –
1
2
TAILCAP
1
2
3
4

6
1. Begin with the Picatinny Mount. Using the provided 2mm Hex Key, loosen
ONLY two (2) of the Mount Screws (see “Taker B10 Reference Guide”
on pg. 3 for location). NOTE: The Mount Screws do NOT need to be
completely removed in order to mount.
2. Position either side of the Picatinny Mount onto the Picatinny C-Clamp.
Then position the opposite side onto the Picatinny Rail. Then, re-tighten
the two (2) Mount Screws that were loosened in Step 1.
OPERATIONAL MODES
For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the flashlight will operate in HIGH mode. When
the user removes pressure from the Switch, the light will turn OFF.
For HIGH mode: Press the Power/Mode Switch two (2) times in rapid
succession. The light will remain in HIGH mode.
For LOW mode: While in HIGH mode, press and hold the Power/Mode
Switch for two (2) seconds. The mode will change to a LOW setting.
For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in
rapid succession.
For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.
NOTE: The light does not retain the mode in memory. Once you turn the
flashlight ON, you will have to re-select the mode you desire.
ASSEMBLING MOUNT TO CLAMP
1
1
2
2

7
The flashlight is easily securable and removable by using the Release Lever.
TO INSERT THE FLASHLIGHT INTO THE HOLDER:
INSERTING/REMOVING FROM THE
HOLDER
1. Insert the flashlight by pushing it into the beveled opening on the front of
the Holder.
2. Once locked, the Release Lever falls into a groove on the handle, securing
the flashlight in place.
TO REMOVE THE FLASHLIGHT FROM THE HOLDER:
12
1. Press and hold the Release Lever.
2. While keeping the Release Lever pressed, pull flashlight out of the Holder.
1
1
1
2
2
2

8
FEATURES
PRESSURE SWITCH
The Taker B10 has an optional Pressure Switch that allows the user to place
it anywhere on the shield. This makes it easier to access the Power/Mode
Switch. The Pressure Switch can easily be attached by twisting the Tailcap in
a counter-clockwise direction to remove it, and replacing it with the Pressure
Switch.
60º TILT
The Picatinny C-Clamp of the Taker B10 can tilt 30º (60º total) on both sides.
This makes it easier to chose direction of light.
MULTIPLE LIGHTS ON ONE SHIELD
Multiple Taker B10’s can be mounted to one shield to disorient rioters.

9
INSTALLING THE TAKER B10
ONTO A SHIELD
1. Loosen the Thumbscrew until the Clamp is free. Then place the Clamp
anywhere along the edge of the shield (The provided rubber spacer can
also be used if required for a better fit).
2. Then align the Clamp and Thumbscrew to the Picatinny C-Clamp Body
and tighten until the Clamp is locked securley in place.
3. To adjust the angle of the B10, use the provided Hex Key (4mm) to loosen
the Tilt Adjustment Screw (see “Taker B10 Reference Guide” on pg. 3 for
location). Then adjust the angle of the Picatinny Mount to desired position.
Re-tighten the Tilt Adjustment Screw to lock in the angle of Flashlight.
1
2
3
BALLISTIC
SHIELD
Place the shield in
between the battery
compartment and
Light Head. (The
shield pictured is cut
in half for this visual)
FRONT OF SHIELD
CLAMP
PICATINNY
C-CLAMP
THUMBSCREW
SIDE VIEW

10
WARRANTY AND OTHER
INFORMATION
PRODUCT DURABILITY
Meets NFPA 1971 Guidelines and can
sustain exposure to 500°F (260°C) for
30 minutes
CARE/CLEANING
Your FoxFury product is a professional
tool, but regular maintenance and care
of your light will maximize performance
for you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that the
flashlight’s Tailcap is SEALED before
washing. When done, pat dry with a
damp cloth.
AVAILABLE ACCESSORIES
SideSlide C-Clamp Adaptor
P/N 85-010
SideSlide Picatinny Adaptor
P/N 85-012
SideSlide Flashlight ONLY
P/N 940-012
SideSlide Picatinny Pressure
Switch Cap, P/N 50-150
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
Lights are strong enough to
cause damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should
be operated at speeds safe
enough to maneuver around
surrounding obstacles.
Do not use under the influence
of drugs or alcohol.
LIMITED LIFETIME
WARRANTY
FoxFury, LLC (“FoxFury”) warrants
this product to be free from defects
in material for a lifetime of use except
for batteries, LEDs, abuse, and
normal wear. We will repair or replace
this product should we determine it
to be defective. This limited lifetime
warranty excludes rechargeable
batteries, chargers, switches, and
electronics, which have a 2-year
warranty with proof of purchase.
This limited lifetime warranty is
given only to the original end user of
the accompanying product. If you
purchased a product from someone
other than an authorized FoxFury
reseller/distributor or if the product
was used, (including but not limited
to demo models, show models or
refurbished product by someone
other than FoxFury) prior to your
purchase, you are not the Original
Purchaser and the product that you
purchased is not covered by this
warranty. This limited warranty is
IPX7
3 M 1 M

11
VOID if this Product has been altered
or modified in any way (including but
not limited to attempted warranty
repair without authorization from
Foxfury and/or alteration/removal
of the serial number). To expedite
warranty concerns, we encourage
the end user to register their FoxFury
Product at www.foxfury.com/pages/
warranty-registration.
THIS IS THE ONLY WARRANTY,
EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARE
EXPRESSLY DISCLAIMED EXCEPT
WHERE SUCH LIMITATION IS
PROHIBITED BY LAW.
You may have other specific legal
rights which vary by jurisdiction. Go
to www.foxfury.com/pages/warranty
for a complete copy of the warranty.
Retain your receipt for proof of
purchase.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Te l : 760.945.4231
Fax: [phone]
Email: [e-mail]
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts.
Products are assembled in either
FoxFury’s controlled plant in Asia or
the USA, under strict quality control.

FOXFURY.COM 10/2018