Franke FHCR 301 1TC HE BK C Release Note

CRYSTAL COOKING GAS
FHCR 301 1TC HE BK C 106.0374.275 6800087
Updated Friday, February 2, 2018
TECHNICAL HANDBOOK

2
FHCR 301 1TC HE BK C 106.0374.275

590x380x165mm NET weight 6,5 kg
HOW IT LOOKS WHEN YOU RECEIVE IT…
3

SERIAL NUMBER
MODEL
FUN
4
LABEL ON THE PACKAGING

FHCR 301 1TC HE BK C 1TRIPLE CROWN
Parameter Value Dimensions (mm) Working dimensions (W x D) - 310 x 510
Power supply voltage / frequency220-240V, 50/60Hz
-
Power / Current 0.6W / 16A
Total installed gas rated power 4.00kW
Total rated capacity - gas G20 0.381m3/h
Total rated capacity - gas G30/G31 291g/h
Air necessary for combustion (2m3/h per kW of installed gas rated power) 8.0
Appliance weight (gross / net) M 7.5 / 6.5 kg
Number of burners 1
Heat source of each burner Gas

TRIPLE CROWN BURNER RATED POWER 4KWREDUCED POWER 1.8KW
Red arrows FIXING POINT TO THE BURNER /CAP
7
TC: Rated capacity G20 (m3/h) 0.381
Injectors G20 20mbar (100/mm): E(2x1,01) + I(1x0,68)
TC :Rated capacity G30 / G31 (g/h)291
Injectors G30/G31 28-30/37mbar (100/mm) : E(2x0,68) + I(1x0,46)

Burner
8
Pan bottom max. Ø (recommended)
TC 280 mm
The use of larger pots than those specified can cause excessive overheating of the knobs and top
and, in case of prolonged use, yellowing of the cover (if in stainless steel).
Franke declines any liability for damage due to such use.
CAST IORN GRID for triple crown WITH RUBBERS
ASSEMBLED KNOB:
KNOB
SPRING
NUT WITH O.RING

INSTALLATION
For fitted units, the components (plastic materials and veneered wood) must be assembled with heat-resistant adhesives
(max. 100°C): Unsuitable materials and adhesives can result in warping and detachment.
The use of hard wood decorative borders around the worktop behind the appliance is allowed, providing a minimum
distance from the edge appliance of:
50 mm for the side wall,
30 mm for the rear and 700 mm for any cabinets above it.
The appliance is recommended to be built into 50mm thick worktops.
Make sure the room where the appliance is installed has permanent ventilation openings towards the outside or
ventilation ducts to ensure an adequate air flow, as prescribed by the current regulations.All openings made must:
– Have a section of at least 100 cm2
Installation procedure
The appliance is fixed to the unit by means of the
bracketsand accessories provided.
Make sure that there is freeaccess to the two fixing
elements in frontafterthe installation of the appliance.
Prepare the hole in the worktop according to the
dimensions indicated.
Mill the worktop along the entire edge of the hole
made forbuilt-in installation.
Apply the sealing strip around the hole and position the hob.
Fix the appliance with the screws and brackets.Remove any excess sealing strip.
9

sealing strip 2x5x2600mm
Hooks
GASKET FOR
CONNECTION GAS 1/2
LPG GAS INJECTORS :
SCREWDRIVER FOR MINIMUM
ADJUSTING
CONNECTION GAS ½ MALE/FEMALE
It is already fitted to the gas hose
10
TC E(2x0,68) + I(1x0,46)
In this picture dia of injectors is 101
marked always on the head of the
injector