Franke FFS3100 User manual

LIMITED LIFETIME WARRANTY
Franke Consumer Products, Inc., Kitchen Systems Division extends
the following warranty to the original purchaser of its faucets effective
January 1, 2003.
All faucets installed in a private residence will carry a limited lifetime
warranty on all mechanical parts to be free of manufacturing defects
in material and workmanship under normal usage. All chrome finishes
carry a limited lifetime warranty; all other finishes are warranted for
five (5) years form the original date of purchase.
Marine and Outdoor Installation: Franke Consumer Products, Inc.
faucets are NOT warranted for Marine and Outdoor installations.
This warranty applies only to the original owner, providing the product
has been installed in accordance with our installation instructions,
used as recommended and in a normal residential application. In the
event of a warranty claim, the owner will be required to provide proof
of purchase - save sales receipt. This warranty covers all components
which make the product operational. Franke, at its option, may repair
or replace the product or components necessary to restore the pro-
duct to good working condition. Franke reserves the right to inspect
the installation prior to the actual replacement of the product or com-
ponent part. This warranty does not cover misuse or abuse, acciden-
tal damages, scuffs or scratches, improper installation, abnormal
usage, negligence or damage caused by improper maintenance or
cleaning. Normal wear of parts is excluded from the warranty.
Damage caused by impurities or acts beyond our control are not
covered. Any product or part which has been repaired or altered in
any manner outside of Franke's factory, unless previously authorized
in writing by Franke, will void warranty. Any replacement excludes
transportation and any labor re-installation costs. This warranty
does not allow recovery of incidental or consequential damages such
as loss of use, delay, property damage or other consequential dama-
ge, and Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the
warranty period specified herein and is exclusive.Franke DISCLAIMS
all other warranties, expressed or implied, including IMPLIED
WARRANTIES OF MERCHANTABILITY AND/OR FITNESS
FOR AS PARTICULAR PURPOSE. This warranty gives you
specific legal rights that may vary from state to state.
Further information
For any further information about our products, about the installation of
them or about the guarantee, please dial the number of the customer
service:
REV. 12/2014 IISTR96600/PER#C08960
STANDARD MAINTENANCE AND TROUBLESHOOTING
REPLACING THE CARTRIDGE
1. Shut o the water supply to the faucet.
2. Turn on the faucet briey to relieve any pressure inside the faucet.
3. Move the faucet handle to the “ OFF” position.
4. Remove indicator cap C from the lever handle.
5. Remove the screw B using an allen key.
6. Pull the lever handle A from the faucet body .
7. Unscrew the cap D.
8. Unscrew the cartridge lock nut E.
9. Lift ceramic disk cartridge F from the body and replace it with new
cartridge. Ensure the two lugs on bottom of the cartridge sit properly
in theallocated holes at the base of the body.
10. Re-assemble faucet in reverse order.
11. Test for leakage.
GENERAL MAINTENANCE
Clean aerator periodically for any buildup .
Do not use harsh detergents, solvents, chemical agents, metallic sponges,
etc. that could harm the surface and damage the nish.
Clean only with a soft sponge and soapy water.
SPARE / REPLACEMENT LIST
F3101*
INSTALLATION MANUAL
FFS3100 -FFS3180
Franke Kitchen Systems
800 Aviation Parkway
Smyrna, TN 37167, USA
Phone: [phone]
Email: [email protected]
D
E
F
J
G
A
A+B+C+G Handle assembly
D. Cap F2902*
E. Lock nut F2903
F. Cartridge F2904
H.
Side Spray Supply Hose F3107
J.
Side Spray Shower
F3106
K.
Aerator WithWrench
F3108*
CH chrome
SN satin nickel
B
C
K
H
*Must specify nish
Mounting HandwaveKit
L.
M.
N.
Side Spray Diverter
Weight
L
M
N
F3110
F3112
F3102
O. Side Spray Mounting Hardware Kit F3109
O

TECHNICAL DATA
NOTE:
Call us immediatly if you see inconsistencies.
(1- 800-626-5771)
or visit
www.frankeksd.com
info[email protected]
CONTENTS IN BOX
1 Faucet assembly
2 Rubber washer
3 Rubber washer
4 Plastic ange
5 Fixing plate
6 Fixing nut
12 Sealing washer
13 Side spray mounting ange
INSTALLATION INSTRUCTIONS
1. Remove all contents from the package and check for completeness.
2. Flush pipe work to ensure it is free from debris.
3. Turn o water supply.
4. Remove faucet and hardware from its protective packaging.
Faucet comes assembled.
5. Cut a mounting hole 1 3/8 diameter (35mm) in the desired position in
counter top or sink (if one isn’t available).
6. Place the rubber washer (2) over the hole for the faucet body
1
5
6
11
Flow Rate
Recommended Water Pressure
Max. Water Pressure
Recommended Hot Water Temp.
Hole Size For Faucet + side spray
Certies this faucet complies with ASME A112.18.1 / CSA B125.1
& NSF 61, NSF 372 and AB1953
1.75 GPM at 45 PSI
30-75 PSI
145 PSI
120°-140° F
1 3/8”
2
4
3
10
7
9
7 Supply hoses
8Side spray supply hose
9Side spray return hose
Side spray shower
11
2
5
1
7
4
3
6
8
10 20
21
17
15
18
14
11
9
14
16
8
13
19
17
15 Rubber washer
16 Plastic spacer
Rubber washer
14
18
20
21
Side spray diverter
10
17 Fixing plate
18 Fixing nut
13
19
19 SIde spray supply hose
20 Weight
22
ATTENTION: For steps 6 and 9
The washer should be sitting between the countertop and faucet base.
DO NOT use putty or other sealant at this location. For solid surface
installation the countertop mounting surface needs to be at and free of
debris, otherwise the faucet or side spray may not sit properly. For tile
installations, avoid installing faucet or side spray near or on top of grout
lines. This may cause a weak joint and could cause leaks.
7. Install the mounting hardware to the base of the faucet body in the
following order – rubber washer (3), plastic ange (4), xing plate (5), and
xing nut (6) as illustrated.
8. Tighten the xing nut (6) onto the body (1)
9. Place the rubber washer (14) over hole for the side spray mounting
ange (13)
10. Install the side spray mounting hardware to the base of the side
spray mounting ange (13), in the following order – rubber washer (15),
Plastic spacer (16), xing plate (17), and xing nut (18).
11. Connect side spray shower (11) to side spray supply hose (19) by
hand. Make sure sealing washer (12) is in place on the supply hose,
otherwise the side spray will leak.
12. Insert the side spray supply hose (19) into the side spray mounting
ange (13) from the top
13. Connect the side spray supply hose (8) coming from the faucet
body to the top of the side spray diverter (10).
14. Connect the side spray return hose (9) to the left side (largest
tting) of the side spray diverter (10).
16. Secure the weight (20) to the side spray supply hose (19) with the
screws (21) approximately 2” (50mm) above the bend in the bottom of
the side spray supply hose (19).
17. Connect the supply hoses (7) to the water supply in the home and
turn on the faucet. Ensure everything is functioning properly and
check/test for leaks.
15. Connect the bottom (smallest tting) of the side spray diverter (10) to
the side spray supply hose (19).
21 Screws
22 Aerator wrench
12
15
16
12
2” (50 mm)