Franke FSW908TC WH User manual

HANDBOOK HOOD FSW908TC WH/XS 9925084 110.0030.787 UPDATED JANUARY 2010
CONTROL type : PUSH BUTTONS KEY- TOUCH CONTROL
MOTOR : NR 01 330 W
TOTAL POWER : 370 W
FLOW RATE - FREE DELIVERY : 920 M3/H MAX
FLOW RATE IEC 61591 850/740 M3/H MAX
PRESSURE 440 PA MAX
SOUND POWER(IEC 60704-2-13): 66 DBA
NO SPEED POSITIONS : N0 8 + BOOST
LAMPS : NR 02 HALOGEN LAMPS X 20 W each one
LIGHTING SYSTEM CAN BE MODIFIED UP TO FIVE LEVELS.
GREASE FILTER : aluminium cassette
DIAMETER : 150 MM-120 mm adaptor supplied
IMPUT VOLTAGE 230V -50 HZ
1

TECHNICAL DATA
SPEED BOOST 8 7 6 5 4 3 2 1
Q MAX 920 750 650 550 480 410 350 280 200
Q IEC 850 700 620 530 460 390 330 265 190
P 440 420 400 390 360 320 280 200 100
W 330 220 180 135 110 90 70 50 35
DBA 66 61 58 55 52 49 46 42 35
2

3

4

ELECTRICAL CONNECTION •
Connect the hood to the mains through a two-pole switch having a contact gap of at least 3
mm.
• Remove the grease filters (see paragraph Maintenance) being sure that the connector of the
feeding cable is correctly inserted in the socket placed on the side of the fan.
Metal grease filters Metal filters can be washed also in a dish machine. They need to be washed every
time a drop-symbol appears in the display or at least every two months. In case of
very frequent use these have to be washed even more often. Alarm reset • Press
the G-key for at least 2 seconds.
Cleaning
• Open the comfort panel.
• Remove the filters one by one by pushing them backwards and pulling them
down contemporaneously.
• Wash the filters. Pay attention not to bend them. Make sure that filters are
completely dry before putting them into their seat. (a possible modification of the
filter surface doesn’t influence its efficiency).
• Place the filters again into their seats and make sure that the handle of the filter
remains outside.
• Close the comfort panel.
5

Hood body mounting Firstly, it is necessary to adjust the two Vr-screws of the 11a-
brackets, at minimun (B).
• Hang the hood body on the two brackets 11a.
• Connect the hood to the mains supply by means of a bipolar switch
with at least 3 mm contact gap.
• Press the “A”-key for one second (see Part USE) to open the upper
panel.
• Remove the metal filters.
• In order to align the hood it is necessary to adjust the Vr-screws
from inside the hood.
• Fasten the safety screw 11.
• Fit again the metal filters into their seats and close the upper panel
by pressing “L”-key for one second (see Part USE).
• Disconnect the hood from the mains supply. Attention: the upper
panel stops if any barrier occurs in its way during the panel opening
or closing.
To open the panel it is enough to remove the barrier and press the
key once again.
6

KEY- FUNCTION DISPLAY
A Upper panel closed: when pressed for
about one sec-ond it opens the upper panel.
It switches the motor on at the latest selected
speed. Upper panel open: when shortly
pressed it switches the motor on/off
Indicates the selected speed.
B Decreases the suction speed.
The number of lit LEDS decreases.
C Increases the suction speed. The number of lit LEDS increases.
D Functioning only when the upper panel is
open. This speed has been timed at 10
minutes. After that time the system activates
automatically the latest selected speed. The
function is suitable for cooking conditions
when vapours and smells are of the utmost
emission.
I flashes and all the LEDS on the display are lit. By pressing the key
the function is deactived
E Functioning only when the upper panel is
open. By pressing this key it is possible to set
up the motor to a suction speed at 100 m3/h .
24 appears and the LEDS extinguish one by one. By pressing the
key the function is stopped
F Functioning only when the motor is on. By
pressing this key it is possible to set the A flashing clock-symbol appears. By pressing the key the function is
7

delayed shutdown of the motor and the
lighting to 30 minutes. stopped
G By pressing this key for about 2 seconds it
is possible to reset the filter saturation alarm
A drop symbol indicates that the metal grease filters saturation alarm
has been activated, and the filters need to be washed. The alarm is
triggered after 100 working hours. C indicates that the charcoal filter
satura-tion alarm has been activated, and the filter has to be
replaced. The alarm s triggered after 200 working hours.
H By pressing this key the intensity of the
lighting system can be modified up to five
levels.
I Upper panel closed: when pressed for about
1 second it opens the upper panel and sets
the lights at the maximum intensity. Upper
panel open: when shortly pressed it switches
the lights on/off.
L Upper panel closed: when pressed for
about one second it opens the upper panel
and switches the motor on at the third speed
and the lights at the maximum intensity.
Upper panel open: when pressed for about 1
second it switches off motor and lights
resetting every activated function, and closes
the upper panel.
Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass. The
motor and lights are switched off, and upper panel can be open or closed. By pressing the F-
key (Delay) for about 5 seconds the keyboard block can be activated or de-activated. This
function is confirmed by a Beep and by moving motor LEDS on display.
8

Charcoal filter (recycling version)
This filter cannot be washed or regenerated. It must be
replaced when the C appears on the display or at least once
every 4 months.
The filter saturation alarm has to be activated already before.
Activation of the alarm signal • In the recycling version hoods
the filter saturation alarm must be activated during the
installation or later.
• Switch off the hood and the lights.
• Press the E-key for about 5 seconds until the last two
segments of the motor LEDS are lit on the display.
• By releasing the E-key the clock icon starts to flash.
• Within 3 seconds press the D-key to activate/deactivate
charcoal filter saturation alarm.
• C-symbol lit - charcoal filter saturation alarm ACTIVATED. •
C-symbol unlit - charcoal filter saturation alarm
DEACTIVATED.
ON OF THE CHARCOAL FILTERSUBSTITUTI
Alarm reset
• Switch off the motor and the lighting system.
ast 2 seconds. Substitution of the filter• Press the G-key for at le
• Open the confort panel.
• Remove the metal grease filters. ated in the picture.• Remove the charcoal filter as indic • Place the filter again into its seat.
Place again the metal grease filters into their place.•
LIGHT REPLACEMENT
20 W halogen light. • Extract the lamp from the lamp holder by pulling gently. • Replace with another of the
ame type, making sure that the two pins are properly inserted in the lamp holder socket holes.s
9

Replacing the fuse
The hood panel opening and closing mechanism is controlled by a starter motor which is activated by a
fuser.
This fuser works only on the starter motor. In case the fuser gets damaged when the panel is closed it is
be necessary to manually unblock the panel. In this case proceed as follows:
• Remove the cover placed up on the left side.
• Press the releasing lever with the screwdriver as much as necessary to enable the manual opening of
the panel.
• After having completely opened the panel remove the metal grease filters, as explained in the part
concerning the filter cleaning.
• The fuser is placed up on the right side. Turn the fuser holder as indicated. Replace the fuser with one
having the same features.
• Put the fuser holder and grease filters into their place again. Make sure that the hood functions
correctly.
In case the panel doesn’t work correctly it is necessary to contact an authorized technician. If the fuser
gets damaged being the panel open, it is sufficient to simply remove the grease filters and replace the
fuser .
10