Fraser Hill Farm FSWL018SQA-RD User manual

1) Schematicdiagram
2) List ofComponents
No.
Name
Quantity
1
L-shapesupport
1
2
hold-nut
1
3
lamp
1
4
lamppendant
1
5
U-shapedfastener
1
6
built-in wire
1
7
powerwire
1(138in)
8
adapter (12VAC500mA)
1
9
extendedwire
1 (138in)
10
ironnail,screwandexpansion tube
7
Note
1,2,3,4,5,6are wire connectors
3) Assembly process
I. Determine installation site
It is suggested to install at the height of 71in from the
groundto getthebestviewangle.
If choosing outdoor installation, there must access to
power to penetrate into the house through gaps of
windowsordoors toavoidtheadapterandmain power
supply to be dampened.
II. InstallL-shapedsupport
Method A: As shown in the above figure. It is to fix the
lamp with only one iron nail (if your unable to use the
ironnaildueto thewallmaterials,usescrewexpansion
tube instead). The advantage of this method is that it
can reduce damages on the wall surface. If there has
been an iron nail (or a screw) on the wall already, it
only needs to have the length adjusted slightly. The
disadvantage of this method is that the lamp may be
swayed by the external force and is not very sturdy.
Therefore, this method is appropriate for the places
where cannot be influenced by the strong wind or
human touch. The preferred method is: to fix the
supplied iron nail (or screw + expansion tube) on the
wall surface which shall be 2-3mm away from the cap
of the iron nail (or screw) so that the lamp can be
suspendedon itasshownin thefollowingfigure.
Then use two screws to fix U-shaped fastener (5) into
L-shaped support (1):
Connect the plug (4) of power wire (7) with the socket
(3) of built-in wire (6) and then suspend L-shaped
support (1) on the wall.
Method B: if the lamp holder is easy to be effected by
wind or human activities, it needs to be fastened. It is
Caution
This product (especially the lamp holder) is
fragile, do not exert too much strength or drop it
during the assembly and use. Be sure to fix iton
thewallsecurely.
This product is waterproof; but it is necessary to
keep the lamp in the vertical direction to ensure
waterdrains correctly.
Please assemble it in strict accordance with
the steps and requirements specified in the
instruction to ensure safety and reliability
during the installation.

The outdoor installation must beconvenient for power wire to
penetrateinto the house throughgaps of windows or doors.

suggested to use Method B to install L-shaped support
(1).Thepreferredmethodis:drilltwo circularholeswith
diameter of X mm and depth Y mm, and use two
expansion tubes and grub screws to fix U-shaped
fastener (5) on the wall, then use two screws to fix
L-shaped support (1) on the U-shaped fastener. But
before do this, do not forget to connect plug (4) with
socket (3)as shown in theabovefigure:
3. Fix the lamp
a．Connect power wire to the lamp: After ensuring the
L-shaped support is well suspended on the wall, insert the
plug (2) of the built-in wire into the socket (1) on the top of
thelamp(3):
b. Fix lamp: liftthelamp(3)upso thatthe upperpartof the
plug (2) and its wire can enter into the hole of the hold-nut
(2), and turn the hold-nut (2) to let it tightly fit the thread of
the upper part of the lamp until the lamp and L-shaped
support to be fixed as a whole. Meanwhile, adjust the
direction of the lamp until it is satisfied. Note: #1. The hold
nut must be screwed tightly; otherwise, the waterproof
effect of lamp holder will be seriously affected. #2. The
lamp holder is fragile, and damage could result from falling
onthe ground.
c. Turn the lamp pendant (4) to fix it with the thread under
thelamp.
4. Power onand examination
a．Power on: connect the plug (5) of power wire (7) with
thesocket(8)ofadaptor(8). If thepower wire(7)isnotlong
enough, add extended wire (9) between those two and
connect (5) and (6), (7) and (8) separately. After that,
connectthe adapter(8) withmainpowersupply.
b. Examination: thereis aswitch at the bottomof the lamp
(3) (see the following figure). Turn on the switch to left side,
the lights should be twinkling, snow flying around, and
music playing. If the above are not functioning, check
whether the connections are properly tightened. You can
alsoturnthe switch to rightsidetoturnoffthemusic.
5.Attention forRainproof
Ifthelampisusedoutdoor,pleasepayspecialattention:
a. Please fix the hold-nut at the top of lamp securely,
otherwise the rainproofeffect willbe seriouslyaffected!
b. All connection points 1, 2, 3, 4, 5, 6, 7 and 8 must be
screwedsecurelytoavoidwaterandelectricityleakage.
c. The adapter itself is not waterproof, but is required. To
ensure that the connectors between adapter and main
powerwork properlyplace thisindoorsfree fromrainand
snow, so as to avoid the electricity leakage or electric
shockrisk!
d. The end of L-shaped support is arranged with drip hole,
and thisholeshouldbeunobstructed;
e. The lamp should be kept vertical and avoid inclined to
ensurethewaterdrainsproperly.