Freedom LARSSON 23418271 User manual

Page 1 of 3Freedom Customer Service: 1300 135 588www.freedom.com.au
LARSSON BUFFET
23418271
Thank you for purchasing the LARSSON BUFFET. Before you begin to assemble your new piece of
furniture, please check to ensure that all hardware and parts have been supplied. This page lists all
contents included in the carton(s).
Follow instructions closely as deviation from them may present a possible safety risk and may void your
warranty.
It is recommended that assembly is done on a soft surface such as carpet to avoid any damage.
If you experience any problems with your new purchase please phone Freedom Customer Service (FCS)
on 1300 135 588. Customers outside Australia should contact their closest Freedom store.
Periodically check and re-tighten any fasteners. Dust weekly using a soft, clean cloth. Do not use harsh
abrasives, chemicals or polishes containing silicone. Avoid direct sunlight as this will cause the timber
to change colour. It is important to remove moist substances immediately. Use coasters, placemats and
table runners to assist in prolonging the life of your product.
Hardware (Supplied)
Tools Required (Not Supplied)
Parts
Care Information
4 x Part A 4 x Part B 4 x Part C 1 x Part D
2 x Part E 2 x Part F 4 x Part G
Part H
Part I
Part I

Page 2 of 3Freedom Customer Service: 1300 135 588www.freedom.com.au
LARSSON BUFFET
23418271
Step 1
Step 2
Part H
Back view
Part D Part A
Part B
Part C
Part I
Part I
Part G
Part F
Predrilled holes

Page 3 of 3Freedom Customer Service: 1300 135 588www.freedom.com.au
LARSSON BUFFET
23418271
Step 3
Step 4
The wall
Part G
Drill a hole on the wall
IMPORTANT: The screw supplied with the anti-tilt strap is to be used only for fixing the
anti-tilt strap to the furniture. In addition to this you will need to choose a screw or wall
fitting which is suitable for your wall type to secure the strap to the kind of wall that you
have. If you are unsure about what type of screw or wall fitting to use, please contact
your local hardware store.
Part E
Push to tighten

Assembly Instructions
Hinge Adjustment
Page 1
Follow instructions closely as deviation from them may void your warranty and present a possible safety risk.
If you experience any problems with your new purchase please phone Freedom Customer Service (FCS) on
1300 135 588 (Customers outside Australia should contact their closest Freedom store.)
Assembly Instructions
Hinge Adjustment
Page 2
DoorCarcass
DoorCarcass
DoorCarcass
Lateral Movement
Horizontal Movement
How to fix it
- To move the door towards the centre of the unit,
loosen Screw "A". Adjust the door and then tighten Screw
"B".
- To move the door away from the centre of the unit, loosen
Screw "B". Adjust the door and then tighten Screw "A".
What it looks like
- The door will not be flush with the side panel.
What it looks like
- The door will appear too far or too close from
the front edge of the side panel.
Screw "A"
Screw "B"
Vertical Movement
How to fix it
- To move the door towards or away from the horizontal
panels, loosen Screws "C". Adjust the door and then
tighten Screws "C".
What it looks like
- The door will not be flush with the vertical
panel.
Screw "C"
Screw "C"
How to fix it
- To move the door towards or away from the unit, loosen
Screw "A". Adjust the door forwards or backwards until
there is an even gap between the door and the front edge
of the side panel.
- Tighten Screw "A" once the adjustment has been made.
Screw "A"