FRENCH FITNESS FF-X9LP User manual

FF-X9LP
ASSEMBLY MANUAL
Functional Multi Gym System w/Leg Press

FEATURES
•
•
•
•
with ease
•
bearings
•
TECH SPECS
•190 lb Weight Stack
•Lat Pulldown: Feels like 280 lbs Due to pulley ratio
•Dimensions: 82"D x 91"W x 83.9"H
WARRANTY
• Lifetime Parts and 1 Year Labor Warranty

PartsDiagram
9
13
1
31
12x3
2014 17
30 18
41
46 47
19
67
16
15
4
35
43 45 39 33 34
49 (Ф10) Washer
52 (Ф12)
Flat washer 55 (M2) Washer 56 (M10x60)
Outer Hexagonal Bolt
3(Ф10хФ30)
5(M10x20)
Outer Hexagonal Bolt
58 (M12x130)
Outer Hexagonal Bolt
51 (M12x70)
Outer Hexagonal Bolt
53 (M12)
Lock Nut
50
Positioning Bolt
61
21
23 24
30
10
44
40 (M12x20)
Outer Hexagonal Bolt
57 (M10)
Lock Nut
26 28 27
25
48
Pulley Spacer

PartsDiagram
70 (Ф8) Washer
61 (M10x16) 63 (M10x85)
Outer Hexagonal Bolt
62 (M12x75)
Outer Hexagonal Bolt
64 (M10x130)
Outer Hexagonal Bolt
73 (M10x110)
Outer Hexagonal Bolt
65 (M10x45)
Outer Hexagonal Bolt
69 (M8x45)
Outer Hexagonal Bolt
66 (M10x115)
Outer Hexagonal Bolt
72 (M10x70)
Outer Hexagonal Bolt
120 (M10x35)
Outer Hexagonal Bolt
71 (M8) Lock Nut
59 (Ф17x123) 60 (Ф16x137)
22
2
11
42
38 37 36
29
Cable166.5"
41
8
54
Adjustment Board
105
106 122 123
124 129
128
125 х2
108
126
127
110
109 (M25x112)
Shaft
67
Cable 57.5"
68
Cable 203"
104
Cable 265"

In st all in g S te p 1 Exploded View
4
2
4
5
1
49
5

Installation Instruction
1. Put Φ10 washer (49) over M10*20 outer hexagonal bolts (5),
and fasten the guiding rod assembly (2) to the under frame
weldment (1).
2. Install the cushion (4) on the guiding rod assembly (2).
6

In st allin g Ste p 2 Exploded View
9
7
10
8
6
50
7

Install ing Step 2After Installation
Installation Instruction
1. Place 11 PCS cast iron counterweight lower piece (7) and cast iron counterweight top
piece (6) in sequence on the upper end of the guiding rod assembly (2).
2. Place bushing (10) into cast iron counterweight top piece (6).
3. Insert the lifting rod (9) and the cast iron counterweight lower piece (7) and the cast iron
counterweight top piece (6) together, and install the positioning bolts (50) on the cast
iron counterweight top piece (6).
4. Insert the magnetic pin (8) on the cast iron counterweight lower piece (7) and the lifting
rod (9).
Note: The outer hexagonal bolts need to be tightened.
8

Installing Step 3 Exploded View
11 40
12
52
52
53
52 52
53
51
52
52
9

Installing Step 3After Installation
Installation Instruction
1. Fasten the inclined support beam (12) to the chassis assembly with M12*70
outer hexagonal bolts (51), Φ12 at washers (52), and M12 lock nuts (53).
2. Use M12*20 outer hexagonal bolts (40) and Φ12 at washers (52) to x the
inclined support beam adjustment board (54).
Note: The outer hexagonal bolts need to be tightened.
10

In st all in g Ste p 4 Exploded View
13
14
14
13
56 56
5
55
51
55
55
53
53
11

4
Installation Instruction
1. Fix the shield support frame (14) and the upper beam (13) together with M10*60
outer hexagonal bolts (56), Φ10 washers (49) and M10 lock nuts (57).
2. Connect the upper beam (13) and the guiding rod (2) together, and fasten them
with M10*20 outer hexagonal bolts (5), Φ10 washers (49) M10 lock nuts (57).
3. Fasten the upper beam (13) to the inclined support beam (11) with M12*70 outer
hexagonal bolts (51), M2 washers (55), and M12 lock nuts (53).
Note: The outer hexagonal bolts need to be tightened.
12

In st allin g S te p 5 Explod ed View
16
15
15
16
53
52
52
52
52
58
13

Installing Step 5 After Installation
Installation Instruction
1. Use M12*130 outer hexagonal bolts (58), Φ12 washers (52) and M12 lock nuts (53) to fasten
the decorative boards (15, 16) to the upper beam and the inclined support beam assembly.
Note: The outer hexagonal bolts need to be tightened.
14

In st allin g Ste p 6 Exploded View
17
20
18
19
17
30
20
5
19
18
5
49
49
51 52
53
15

Installing Step 6After Installation
Installation Instruction
1. Use M12*70 outer hexagonal bolts (51), Φ12 washers (52) and M12 lock nuts (53) to fasten
the seat support in tube assembly (18) to the lowerhole of the inclined support beam.
2. Install the kick rotation shaft (30) on the foot hook bending tube (31), andthen connect the
foot hook bending tube (19) and the seat supporting tubeassembly (18) together, and
fasten them on both ends of the kicking shaft (30)using M10*20 outer hexagonal bolts
(5)andΦ10 washers (49).
3. Install the seat cushion adjustment tube (17) on the seat supporting tube (18) and tighten it
witht hehexagonal reset pull pin (20).
Note: The outer hexagonal bolts need to be tightened.
16

In st allin g Ste p 7 Exploded View
40
52
60
21
38
12
22
59
5
38
59
5
17

Installing Step 7After Installation
Installation Instruction
1. Use the Φ17*123 front pushing frame shaft (59) to connect the front pushing frame (21) and
the decorative boards (15, 16) together, and fasten it to both ends of the front pushing frame
shaft (21) with M10*20 outer hexagonal bolts (5) and Φ10*Φ30 washers (3).
2. Connect the front pushing arm (22) and the front pushing frame (21) together with the
Φ16*137 front pushing arm connection shaft (60), and fasten it on both ends of the front
pushing arm connection shaft (22) with M12 *20 outer hexagonal bolts (40) and Φ12 at
washers (52).
3. Connect the reset pull pin (12) and the front pushing frame (21) together .
Note: The outer hexagonal bolts need to be tightened.
18

In st allin g Ste p 8 Exploded View
23
38
24
25
26
49
49
61
62 52
52
53
57
63
19

Installing Step 8After Installation
Installation Instruction
1. Fasten the buttery arm-left (24) to the buttery arm xing board of the inclined support beam with
M10*16 outer hexagonal bolts (61) and Φ10*Φ30 washers (3).
2. Fasten the buttery arm-right (23) to the buttery arm xing board of the inclined support beam with
M10*16 outer hexagonal bolts (61) and Φ10*Φ30 washers (3).
3. Pass the M12*75 outer hexagonal bolts (62) andΦ12 washer (52) through the inclined support beam
and the inclined support pulley frame(25), and fasten the other end to the M12*75 outer hexagonal
bolts (62) with M12 lock nut (53) and Φ12 washer (52).
4. Use M10*85 outer hexagonal bolts (63), Φ10 washers (49) and M10 lock nuts (57) to fasten the pedal
board (26) on the seat supporting tube assembly.
Note: The outer hexagonal bolts need to be tightened.
20