Frigidaire FGGC3645KSC User manual

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETY:
-- Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
-- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
-- installation and service must be performed by a qualified installer,
service agency or the gas supplier.
Appliances installed
in the state of
Massachusetts:
ThisAppliancecanonly
be installedin the state
of Massachusettsbya
Massachusettslicensed
plumber or gasfitter.
Thisappliancemustbe
installedwith a three (3)
foot /36 in. long flexible gas
connector.
A "T" handletype manual
gasvalvemust be installed
in the gassupplyline to this
appliance.
Gas Cooktop
Dimensions
21/2 _
(6.4
Gas Cooktop (6.4 cm) ,o
Cutout Dimensions , ii ,[
Figure I
30" GasCooktop 30(76.2) 21 3/4(55.2) 4 ¼(10.8) 27 (68.6) 19(48.3)
36" GasCooktop 36(91.4) 21 3/4(55.2) 4 ¼(10.8) 33 ¼(84.5) 19(48.3)
30"GasCooktop 27¼(69.2) 28Y2(72.4) 19_/s(48.6)
36"GasCooktop 337/8(86.1) 34¼(87) 19_/8(48.6)
All dimensions are stated in inches and (cm).
DimensionH includesa 5" (12.7 cm) spaceunderneaththe cooktop for connectionto gassupplyline.
NOTE: Wiring diagrams for this cooktop are enclosed in this booklet
Printedin United States
193/4(50.2) 8(20.3)
193/4(50.2) 8(20.3)
318201482 (0811) Rev.A
English - pages 1-9
Espaflol- p_iginas 10-18
Fran_ais - pages 19-26
Wiring Diagram 27-28

important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the cooktop.
2. Remove all packing material before connecting the
electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
5. Note: For operation at 2000 ft. elevations above see
level, appliance rating shall be reduced by 4 percent
for each additional 1000 ft.
important Note to the Consumer
Keep these instructions with your Use and Care Guide for
future reference.
IMPORTANT SAFETY
INSTRUCTION
Installation of this cooktop must conform with local
codes or, in the absence of local codes, with the National
Fuel Gas Code ANSI Z223.1/NFPA 54 in the United
States, or in Canada, with the Canadian Fuel Gas Code,
CAN/CGA B149 and CAN/CGA B149.2.
• When installed in a manufactured (mobile) home
installation must conform with the Manufactured
Home Construction and Safety Standard, title 24 CFR,
part 3280 [Formerly the Federal Standard for Mobile
Home Construction and Safety, title 24, HUD (part
280)] or, when such standard is not applicable, the
Standard for Manufactured Home Installation, ANSI/
NCSBCSA225.1 or with local codes where applicable.
This cooktop has been design certified by CSA
International. As with any appliance using gas and
generating heat, there are certain safety precautions you
should follow. You will find them in the Use and Care
Guide., read it carefully.
Be sure your cooktop is installed and grounded
properly by a qualified installer or service
technician.
This cooktop must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA
No. 70--latest edition in the United States, or in
Canada, with the Canadian Electrical Code, CSA
C22.1 Part 1.
The burners can be lit manually during an
electrical power outage. To light a burner, hold a
lit match to the burner head, then slowly turn the
Surface Control knob to LITE. Use caution when
lighting burners manually.
Do not store items of interest to children in
cabinets above the cooktop. Children could be
seriously burned climbing on the cooktop to reach
items.
To eliminate the need to reach over the surface
burners, cabinet storage space above the burners
should be avoided.
Adjust surface burner flame size so it does not
extend beyond the edge of the cooking utensil.
Excessiveflame is hazardous.
Never use your cooktop for warming or heating
the room. Prolonged use of the cooktop without
adequate ventilation can be hazardous.
Do not store or use gasoline or other flammable
vapors and liquids near this or any other
appliance. Explosions or fires could result.
The electrical power to the cooktop
must be shut off while gas line connections are
being made. Failure to do so could result in serious
injury or death.

13"(33
Max.Depth
ForCabinet
InstalledAbove
Cooktop.
A
18" Min.
(45.7 cm)
2" (5.1 cm) Minimum Distance
_etween Rear Edge of Cutout
Nearest Combustible Surface
Above Countertop.
30" (76.2 cm) Min.
Clearance Between
the Top of the
Cooking Platform
_l_oan d Unprotected
ndetr Metal
Clearance
To eliminate the risk of
burns or fire from reaching over heated
surfaces, cabinet storage space located
above the cooktop should be avoided. If
cabinet storage is provided, risk can be
reduced by installing a range hood that
projects horizontally a minimum of 5"
(12.7 cm) beyond the bottom of the
cabinets.
21/4'` (5.7 cm) Min.
From Counter Edge to
Front Edge of Cutout.
If a drawer is present underneath, allow
at least 61/2"(16.5 cm) of clearance
below the counter top. Make sure there
will be no interference with gas or
electrical connection.
Never store flammable
products in the drawer.
30"C00kt0p
36"C00kt0p
30"(76.2cm)
36"(91.4cm) 7" (17.8cm) 7" (17.8cm) 7" (17.8cm) 7" (17.8cm)
Figure 2 - CABINET DESIGN
3

Typical Under Counter Installation of an
Oven with a Cooktop Mounted Electric Built-in
Above
Only certain cooktop models may be installed over
certain built-in electric oven models. Approved cooktops
and built-in ovens are listed by the MFG ID number
and product code (see the insert sheet included in the
literature package and cooktop installation instructions
for the dimensions).
To reduce the risk of
personal injury and
tipping of the wall
oven, the wall oven
must be secured to
the cabinet (s) by
mounting brackets.
208/240 Volt junction box
for built-in oven.
Approx. 3"
(7.5 cm)
I
I
Cabinet side filler panels
are necessary to isolate the
unit from adjoining cabinets.
Cabinet side filler height
should allow for installation of
)roved cooktop models
36" Min.
(91.4 cm) Min.
Use 3/4" (1.9 cm) plywood, installed on
two runners, flush with toe plate. Base
must be capable of supporting 150
pounds (68 kg) for 27" models and
200 pounds (90 kg) for 30" models.
Cut an opening in wood base minimum 9" x
9" (23 X 23 cm), 2" (5 cm) from left side filler
panel, to route armoured cable to junction box.
4 1/2" (11.5 cm) Max.*
* If no cooktop is installed
directly over the oven unit, 5"
(12.7 cm) maximum is allowed
above the floor.
27"(68.6) 247/8'' (63.1) 25V4"(64.1) 23V2"(59.7) 27V4"(69.2) 28V2"(72.4)
30"(76.2) 28Y2"(72.4) 29"(73.7) 23Y2"(59.7) 27¼"(69.2) 28Y2"(72.4)
Figure 3

Typical Gas Cooktop Installation Over
an Electric Built-in Oven Installed Under the Counter
A__ I_l----- 18" (45.7 cm) Max.-----_
Manifold Pi
Flexible Connector
61/2"
5"cm)(16.5 cm)
Flare (12.7 Min.
Union
Cabinet sides or
filler panel
Flare
Union
Wall Oven Cabinet
120V/6OHz
Grounded
Outlet
Pressure
Regulator
÷
4" (10.2 cm)
Right Side
of Cabinet
Manual Shutoff Valve
(Tobe accessible for
shut-off valve opera-
tion)
Figure 4

1. Wall Outlet Location
12" _,1
,_._(30.58 cm)
12_0.3cm)_'l_J 10"
<25._cm>
120Vgroundedoutlet
on rearwall.
_[_Center line 22"
Of unit (55.9 cm)
, NOTE:If anoutlet l
t isnotavailable,
, haveoneinstalledby
'l aqualifiedtechnician.
" " ._:Center line
Of unit
Figure 5
2. Cooktop Installation
1. Visually inspect the cooktop for damage.
2. Set the cooktop into the countertop cutout.
After inserting the cooktop into the countertop
opening, make sure the unit is sitting on the metal
flange around the top of the burner box. Cooktop
must not sit on the glass or the porcelain top. Avoid
cutting an oversized hole in the countertop.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.
Clamp Down Information
Once the cooktop is installed in the counter opening,
you must clamp the unit down as shown.
Seal (Porcelain
Cooktop (Glass Cooktop Only)
or Porcelain) _ /
, _ _ _ Countertop
Angle
Bracket__ __
_fl _Thumb
Screw
Figure 6
To clamp down, insert an angle bracket into the slot
on each side of the unit as shown. Run thumb screw
up through the bracket, up against the bottom of the
counter. Tighten until the unit draws down and is secure.
3. Provide an Adequate Gas Supply
This cooktop is designed to operate on natural gas at 4"
of manifold pressure only.
A pressure regulator is connected in series with the
manifold on the cooktop and must remain in series with
the supply line.
For proper operation, the maximum inlet pressure
to the regulator must be no more than 14" of water
column (W.C.) pressure.
For checking the regulator, the inlet pressure must be at
least 1" (or 2.5 kPa) greater than the regulator manifold
pressure setting. The regulator is set for 4" of manifold
pressure, the inlet pressure must be at least 5".
The gas supply line to the range should be 1/2" or 3/4"
pipe.
4. LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
A kit for converting to LPgas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANEGAS
CONVERSION".
The conversion must be performed by a qualified service
technician in accordance with the kit instructions and
all local codes and requirements. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
Failure to make the appropriate conversion
can result in serious personal injury and property
damage.
Important: Remove all packing material and literature
from cooktop before connecting gas and electrical
supply to cooktop.

5. Install Pressure Regulator
Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position
where you can reach the access cap.
Do not make the connection too tight.
The regulator is die cast. Overtightening may crack the
regulator resulting in a gas leak and possible fire or
explosion.
Manual GAS FLOW Pressure
Shutoff Flare _ Flare Regulator
Valve Union Union
_-_ Nipple Flexible Nipple Access
Off Connector Cap
All connections must be wrench-tightened
Figure 7
Assemble the flexible connector from the gas supply pipe
to the pressure regulator in the following order:
1. manual shutoff valve
2. 1/2" (1.3 cm) nipple
3. 1/2" (1.3 cm) flare union adapter
4. flexible connector
5. 1/2" (1.3 cm) flare union adapter
6. 1/2" (1.3 cm) nipple
7. pressure regulator
Use pipe-joint compound made for use with Natural and
LP/Propane gas to seal all gas connections. If flexible
connectors are used, be certain connectors are not
kinked.
The supply line must be equipped with an approved
manual shutoff valve. This valve should be located in the
same room as the cooktop and should be in a location
that allows ease of opening and closing. Do not block
access to the shutoff valve. The valve isfor turning on or
shutting off gas to the appliance.
Shutoff Valve -
Open position
Figure 8
Once regulator is in place, open the shutoff valve in the
gas supply line. Wait a few minutes for gas to move
through the gas line.
Check for leaks. After connecting the cooktop to the
gas supply, check the system for leaks with a manometer.
If a manometer is not available, turn on the gas supply
and use a liquid leak detector (or soap and water) at all
joints and connections to check for leaks.
Do not use a flame to check for leaks from
gas connections. Checking for leaks with a flame may
result in a fire or explosion.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment of control knob valves after
connecting the cooktop to the gas supply to be sure the
cooktop manifold pipe has not moved. A misalignment
could cause the valve stems to rub on the control panel,
resulting in a gas leak at the valve.
Disconnect this cooktop and its individual manual
shutoff valve from the gas supply piping system during
any pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa or 14"water column).
Isolate the cooktop from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3.5 kPa or 14" water column).
7

6. Electrical Requirements
120 volt, 60 Hertz, properly grounded branch circuit
protected by a 15 amp circuit breaker or time delay fuse.
Do not use an extension cord with this cooktop.
7. Check Operation
Refer to the Use and Care Guide packaged with the
cooktop for operating instructions and for care and
cleaning of your cooktop.
Grounding Instructions 1. Remove foam caps.
IMPORTANT Pleaseread carefully.
For personal safety, this appliance must be properly
grounded.
The power cord of this appliance isequipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle (see Figure 9) to
minimize the possibility of electric shock hazard from the
appliance.
The wall receptacle and circuit should be checked by
a qualified electrician to make sure the receptacle is
properly grounded.
Preferred Method
.
.
Turn on Electrical Power and Open Main Shutoff
Gas Valve
Check the Igniters
Operation of electric igniters should be checked
after cooktop and supply line connectors have been
carefully checked for leaks and the cooktop has been
connected to electric power.
To operate the surface burner:
A. Push in and turn a surface burner knob to the
LITEposition. You will hear a small ticking noise;
this is the sound of the electric ignitor which
lights the burner.
B. After the burner lights, turn to the desired flame
size. The controls do not have to be set at a
particular mark. Use the marks as a guide and
adjust the flame as needed.
Grounding type
wall receptacle
not, under any
circumstances, cut,
remove, or bypass
the grounding
prong.
Power supply cord with
3-prong grounding plug.
Figure 9
Where a standard 2-prong wall receptacle is installed,
it is the personal responsibility and obligation of the
consumer to have it replaced by a properly grounded
3-prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.

4.Adjustthe"low" settingfor regularsurface
burnervalves(Figure10)
a. Pushinandturncontrolto LITEuntilburnerignites.
b. QuicklyturnknobtoLOWESTPOSITION.
c. Ifburnergoesout,resetcontroltoOFF.
d. Removethesurfaceburnercontrolknob.
e. Insertathin-bladedscrewdriverintothehollowvalve
stemandengagetheslottedscrewinside.Flamesize
canbeincreasedordecreasedwiththeturnofthe
screw.Turncounterclockwisetoincreaseflamesize.
Turnclockwisetodecreaseflamesize.Adjustflame
untilyoucanquicklyturnknobfromLITEto LOWEST
POSITIONwithoutextinguishingtheflame.Flame
shouldbeassmallaspossiblewithoutgoingout.
Counterdo_
Clockwise
5.Adjustthe"LOW"Settingof the DualBurner
SurfaceValve(Figure10)(somemodels):
Note:Onthedualvalvethelowsettingofeachportion
shouldbeadjustedindividually.
a. PushinandturnknobtoLITEthencontinueto turn
untilonlytheinnerportionofthedualburnerstays
on.
b. Quickly turn knob to LOWEST POSITION.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. The inner portion of the dual burner flame size can
be increased or decreased with the turn of the screw
B. Use screw A to adjust the low flame size of the
outer portion of the dual burner. Turn the screw
counterclockwise to increase flame size. Turn the
screw clockwise to decrease flame size. Adjust flame
until you can quickly turn knob from HIGH to LOWEST
POSITIONwithout extinguishing the flame. Flame
should be as small as possible without going out.
Note: Air mixture adjustment is not required on surface
burners.
When All Hookups are Complete
Make sure all controls are left in the OFFposition.
Make sure the flow of combustion and ventilation air to
the cooktop is unobstructed.
Hollow
Valve
Stem
Regular
Burner
Valve
Figure 10
Note: Air mixture adjustment is not required on surface
burners.
Model and Serial Number Location
The serial plate is located on the underside of the
cooktop.
When ordering parts for or making inquires about your
range, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
of your cooktop.
Your serial plate also tells you the rating of the burners,
the type of fuel and the pressure the cooktop was
adjusted for when it left the factory.
Before You Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your Use and Care Guide.
It may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to the warranty in your Use and Care Guide for
our service phone number and address. Pleasecall or
write if you have inquiries about your product and/or
need to order parts.
9

LA INSTALACION YELSERVICIO DEBEN SER REAUZADOS POR UN INSTALADOR CALIFICADO.
IMPORTANTE: GUARDE ESTASINSTRUCCIONES PARA USO DEL iNSPECTOR ELleCTRICOLOCAL.
LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS
I1_ Si todas las instrucdones de 6ste manual no son observadas
a la letra, se puede ocurrir incendios o explosiones que pueden causar da_os
materiales, lesiones o la muerte.
PARA SU SEGURIDAD:
-- No almacene o utilice gasolina u otros vapores y liquidos inflamables cerca
de 6ste o cualquier otro artefacto.
-- QUE HACER SI HAY FUGAS DE GAS :
• No intente de encender ning_n artefacto
• No toque ningun interruptor elOctrico; no utilice ningun aparato telefOnico
en su edifido.
• Llame inmediatamente el abastecedor de gas desde el telOfono de un
vedno. Siga las instrucciones del abastecedor de gas.
• En caso que no puede contactar el abastecedor de gas llame al
departamento de bomberos.
-- La instalaciOn y el servicio telefOnico deben set realizados por un instalador
calificado, pot un servicio tOcnico certificado o pot el abastecedor de gas.
Aparatos Instalados en el
estado de Massachusetts:
Este Aparato s61opuede ser
instalado en el estado de
Massachusetts por un plomero
o ajustador de gas licenciado
de Massachusett.
Este aparato sedebe instalar
con un largo conector flexible
de gas de tres (3) pies/36
pulgadas.
Una wilvula manual de gas de
tipo manija de forma de "T"
sedebe instalar en la I[nea
del suministro de gas de este
aparato.
Dimensiones
de la parrilla
de cocinar
21/2"
(6.4
30" M[n.
(76,2 ore) _B
DimensJones
del hueco de (6.4 cm)
, II
la parrilla de cocinar
Figura 1
Modelode30" 30(76.2) 213/4(55.2) 4 1/4(10.8) 27(68.6) 19(48.3)
Modelode36" 36(91.4) 213/4(55.2) 4 ¼(10.8) 33¼(84.5) 19(48.3)
Modelode30" 271/4(69.2) 28V2(72.4) 19V8(48.6) 193/4(50.2) 8(20.3)
Modelode36" 337/8(86.1) 341/4(87) 19?8(48.6) 193/4(50.2) 8(20.3)
Todas las dimensiones se dan en pulgadas (cm). 318201482 (0811) Rev.A
La dimension H incluye un espacio de 5" por debajo de la plancha de cocinar para la conexi0n English- pages1-9
de la linea de suministro de gas. Espa_ol- p_iginas10-18
NOTA: Se adjunta los diagramas de cables de esta plancha de cocinar con el libreta. Francais-pages19-26
Imprimido en losEstadosUnidos Diagramade la instalaci6nal_imbrica27-28