FRISKA Primo User manual

1
Primo Bluetooth Standing Desk
Assembly Instructions

3
4st. M8x20 8st. M8x20 2st. 4x16 16st. 4,5x20 2st. M8 2st. M8x44 2st. M6x20 2st. M8x16
Primo
L x4
M8x20
M x8
M8x20
N x2
4x16
O x16
4.5x20
Q x2
M8x44
R x2
M6X20
S x2
M8X16
P x2 T x12 U x20
M8 M5x16
B
Dx2
E
Hx2
Cx2
G
J
I
A
4st. M8x20 8st. M8x20 2st. 4x16 16st. 4,5x20 2st. M8 2st. M8x44 2st. M6x20 2st. M8x16
F
K
x2
L x4
C
D
D
E
C
1.
2.

4 5
3.
4.
A
J
A
B
B
M x4
J
5.
x4
M

6 7
6.
12-15 mm
39
12-15 mm
39
12-15 mm
39
12-15 mm
39
x2
7.
8.
x2
Max moment 5 Nm
x2
Q
S
S
PH
H
12-15 mm
39

8 9
Min. 1150 mm
Max.1740 mm
9.
10.
Min. 1150 mm
Max.1740 mm
Min. 1150 mm
Max.1740 mm
Min. 1150 mm
Max. 1740 mm
11.
x12
Rx2
T
25
Min. 1150 mm
Max.1740 mm

10 11
13.
05
10
32
28
32
O
25
25
12. 14.
RESET PROCEDURE
Lower the frame to its lowest position by pressing the down button on the hand
controller. Release the button. Press the button again and keep it pressed for
10 seconds, the reset is now carried out and the frame is ready to use.
4
3
1
2
!
I
J
A
A
!NOTE All leads MUST be connected into the control box
in this specific sequence before connecting the
power lead and switching the power on. Failure
to comply could result in damage to the unit
and invalidate the guarantee. The cable clamps
supplied MUST be securely fixed in the positions
as shown to avoid nuisance tripping of the anti-
collision sensor. Use the wood screws (O) in the
pre-drilled pilot holes provided in the desktop.
Control box layout
Important - Please read the instructions on the following page and
the note below very carefully before starting this section!
15.
!NOTE Use Ox20 only if using desktop
‘O’x20
without metal screw inserts
‘U’x20
Fully
tighten
screws.
Fully
tighten
screws.
Options for mounting the hand controller:
Fixed or retractable Fixing positions are
marked both on the left hand and right hand
side of the underside of the desktop by pre-
drilled pilot holes to make positioning and fix-
ing the switch easier.

14. Switching method options
Physical, Bluetooth or both
Physical Only: The diagram in step 16on the previous
page shows the physical switch "I"plugged directly into the
control box. This enables the desk to be controlled solely
by the physical switch.
Bluetooth Only: To enable the desk to be controlled
solely by Bluetooth (via the phone App) plug the Bluetooth
dongle into port "H"on the control box instead of the
physical switch (See diagram on previous page). The desk
can be operated now without any controls visible.
Both Physical and Bluetooth: In order to facilitate both
Physical and Bluetooth control on the desk, the splitter
cable provided must be used to feed both means of control.
One end of the splitter cable plugs into port "H"on the
control box (and MUST be clamped along with all the other
control cables as shown on the previous page) and the
other ends of the splitter cable plug onto both the
Bluetooth dongle and the physical switch as shown in the
diagram below.
See separate instruction manual for downloading and
operating the Bluetooth control App, "Stand up Please".
Physical Switch
Control Box
Bluetooth Dongle
Splitter Cable
Esto Global Limited T/A: FRISKA
Innovation House, 39 Mark Road
Hemel Hempstead
Herts.
HP2 7DN
T: 0330 133 1937
E: [email protected]