FRISKA Stockholm Bluetooth Corner Standing Desk User manual

Stockholm Bluetooth Corner Standing
Desk Assembly Instructions

D
D
D
O
O
F
'H'
M
I
D
E
E
L
A
A
A
C
C
B
B
B
F
F
F
G
2
Packed with
desktop
N
K
(optional)

3
FIXING
COMPONENT LI T
A- Desk Legs
B- Under-desk Support Arm
C- Cross Beam Connectors
D- Cross Beams
E- Feet (690mm Long)
F- Plastic inserts
G-Power supply lead
H- Control switch (Basic or Memory)
I- Control Box
K- Cable Port Cover (optional)
L- Foot (Short - 490mm)
M- Corner bracket
N- Cable extension (for return leg)
O-Desk fixing plates
REQUIRED TOOLS
HEX
4mm
HEX
5mm
(supplied) (Not supplied)
8x 12x 20x 20x 12x 4x 2x
PQR* S U WY
*R -These screws are used for the frame to desktop fixing
except when using a desktop without metal screw inserts.

4
1.
‘P’ x4
A
A
2.
D
D
F
F
‘Q’ x4
CAUTION
Components are heavy – take care when handling
!
A EMBLE THE MAIN FRAME ECTION
Insert screws but
do not tighten.
Gap needed for
frame and brackets
in steps 3 and 5.
Insert screws but
do not tighten.

5
3.
A
D
A
D
‘P’ x4
Fully
tighten
screws.
Do not tighten: Keep loose for step 5.

6
4.
Unravel leg motor leads and push
into plastic cable tidy slots

7
5.
B
B
Fully
tighten
screws.
x4
It may be necessary to use asoft headed mallet to fit
tight fitting support arm onto the leg / frame.

8
6.
‘Q’x8
E
E
Fully
tighten
screws.

9
7.
‘W’ x4
Hand tighten
fully into foot.

10
8.
Feed leg motor cables
through centre hole
C
Slide 'C' into the gap
between 'D' and 'F' -
keep motor wires clear.

11
Feed leg motor cables
through centre hole
CAUTION
Frame is heavy – take care when positioning it.
!
Slide the second half of the frame as-
sembly onto 'C' - keep motor wires clear

‘P’ x4
A
9.
10.
D
D
F
F
‘Q’ x4
CAUTION
Components are heavy – take care when handling
!
12
A EMBLE THE RETURN FRAME ECTION
Do not tighten: Keep loose for step 15.
Insert screws but
do not tighten.

13
11.
D
D
C
12.
A
Slide 'C' into the gap
between 'D' and 'F'

14
13.
14.
x2
Fully
tighten
screws.
Do not tighten: Keep loose for step 15.

15
15.
x2
Fully
tighten
screws.
L
B
Fully
tighten
screws.
‘Q’x4
It may be necessary to use asoft headed mallet to fit
tight fitting support arm onto the leg / frame.

16.
‘W’ x2
16
Hand tighten
fully into foot.

17
17.
For LEFT HAND
RETURN Desk
mount bracket
to the left side
of the frame
RIGHT HAND RETURN
M
M
M
Fully
tighten
screws.
Loosen screw to
accept bracket
Place bracket (M) keyholes
over the loosened frame
screws and push the bracket
to the right to secure the
keyhole on the screws. For
left hand returns, push the
bracket (M) to the left.

18
18.
Left Hand Return
Hook return leg
assembly onto bracket
as shown
N
N
N
Feed cable
extension 'N'
through the
frame to join
with other
cables.

19
19.
Left Hand Return
NOTE Check desktop for any
damage before commencing
!this stage.
Right Hand Return

20
20
20.
NOTE View is of
underneath desk
!
Fully
tighten
screws.
‘R’x36