FrSky Scout VS600 RED User manual

Instruction Manual for FrSky Scout VS600 Series
Instruction Manual for FrSky Scout VS600 Series
Introduction
Thank you for purchasing the FrSky video transmission device. A simple and clean design, equipped with a
switchable power output and operating band and channel. Paired with a FrSky radio transmitter, the parameters can
be adjusted conveniently through the gTrans.lua script. In addition Scout VS600 BLACK/VS600 RED has a built-in
microphone which transmits audio. To fully enjoy all the features of this device please thoroughly read the
instructions below to set up the device.
Configuration method
1. Manual configuration（by the Button）
Press the button for (3s) to enter the power/channel/frequency selection mode, press the button for (3s) again
to switch between power/channel/frequency.
Features
• Support S.Port
• Support inverted S.Port
• Built-in microphone（Scout VS600 Red & Black）
• Adjustable RF power
• Support set parameters by gTrans.lua /Button /FreeLink(PC)/FreeLink App.
The Scout VS600 Series has a green LED/red LED/blue LED which indicates the RF power/frequency band/chan-
nel. As you press the button key, the LED will flash, indicating the corresponding RF power level/frequency
band/channel.
Transmission Frequency
A
B
C
D
E
F
CH1
5865
5733
5740
CH2
5845
5752
5760
CH3
5825
5771
5780
5732
CH4
5805
5790
5800
5769
CH5
5785
5809
5820
5806
CH6
5765
5828
5840
5843
CH7
5745
5847
5860
CH8
5866
CH
FR（MHz）
LED State
LED
Indication
Flash 1 time
Flash 2 times
Flash 3 times
Flash 4 times
Flash 5 times
Flash 6 times
Flash 7 times
Flash 8 times
Green
Power
Pit mode
25mW
/
/
/
/
/
/
Red
Band
A
B
C
D
E
F
/
/
Blue
Channel
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
Specifications
• Transmission Frequency: 5.8 GHz
• Transmission Power: ＜0.01mW (pit mode) /25mW
Model Name
Scout VS600 RED
Scout VS600 Black
Scout VS600 Mini
L*W*H(mm)
31.5*23.6*4.5
31*24*4.9
15.5*13.5*4
Weight(g)
4.2
4
1.2
Available Channel
26CH
26CH
26CH
Operating Voltage
2-6S
2-6S
5V
Overview
Scout VS600 BLACK
Inverted S.Port
BLUE
RED
GREEN
Button
5V@3A_OUT
GND GND GND
RX
TX
V_IN
S.Port
VEDIO
24 mm
13 mm
13 mm
31 mm
BLUE RED GREEN Button
GND
GND GND
RX
TX
V_IN
Inverted S.Port
S.Port
VEDIO
Scout VS600 RED
23.55 mm
31.52 mm
5V@3A_OUT
BLUE
RED
GREEN
Button
GND
VTX
+5V
Inverted S.Port
S.Port
15.5 mm
13.5 mm
Scout VS600 Mini

Instruction Manual for FrSky Scout VS600 Series
Instruction Manual for FrSky Scout VS600 Series
Greed LED
On
Off
On
Red LED
On
On
Off
Blue LED
Off
On
On
States
Channel setting mode
RF Power setting mode
Frequency Band setting mode
Operation
Press the BUTTON (1.5S)
to change the channel
Press the BUTTON (1.5S)
to change the RF Power
Press the BUTTON (1.5S)
to change the Frequency Band
Note: When setting Channel /Frequency band/RF Power, please strictly follow local laws and regulations.
FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals.
Pit Mode
A feature introduced with Scout VS600 Series is Pit Mode, It allows the user to power up their video transmitter
during race events without interfering with other users and still have the ability to change VTX settings and perform
tests mode features all the functions under Normal mode other than operating power.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC STATEMENT
2. The script configuration
Channel, Operating Band and Operating Power can be set through the transmitter.Run the gTrans.lua which is
on the SD card and start configuration.
The interface is below.
Note: Please running Scout VS600 BLACK/VS600 RED before running the script.
3. FreeLink(PC) configuration
Channel, Operating Band and Operating Power can be set through the FreeLink(PC). Connect Scout VS600
Series to STK or S.Port AriLink S to the computer and configure parameters with FreeLink(PC).
The interface is below.
4.FreeLink App configuration
Channel, Operating Band and Operating Power can be set through the FreeLink App. Connect Scout VS600 Series
to the S.Port AirLink S and configure parameters with FreeLink App in the mobile terminal.