FrSky Edge Warrior User manual
Instruction Manual
1/18 Electric 4WD RC Crawler
Edge Warrior
Desert Brown 03150004
Sky blue 03150005
Meteorite Gray 03150006
7 8
6
The indicator light will flashes 3 times
5
1 2
3 4
CAUTION
高温烫手
Caution! Heat!
EDGE WARRIOR Quick Assembly/Disassembly Manual
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Long press and hold
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Overview
[1]
[2]
[3]
[4]
[5]
[6]
[13]
[15]
[9]
[10]
[11]
[14]
[12]
[8]
[7]
Main Menu Introduction
MDL 1 VOL 8.4V
Light off G L
T1：ST T2：ST
TRIM S.TRIM
PTO N 6.0VDB 0
Battery Installation
1. Open battery cover at bottom of pistol grip, install 4x
AAA batteries as shown
Quick Start Guide for Pistol Grip
[7] Power Switch
[8] Menu Down Navigation Switch Button
[9] Menu Up Navigation Switch Button
[10] Enter Button
[11] Trim Lever (Steering Center Adjustment)
[12] Trim Lever (Throttle Center Adjustment)
[13] Menu Display Screen
[14] Firmware Upgrade Port (Requires Upgrade
Accessory)
[15] Wrist Strap Hole
[1] Steering Wheel (CH1)
[2] Throttle Trigger (CH2)
[3] 3-Position Switch
(Left/Center/Right: High/Medium/Low Speed)
[4] 3-Position Switch
(Left/Center/Right: SPORT/CRAW/NORMAL Mode)
[5] Light Control Button (Day Mode/Night Mode/Night
Mode with Top Spotlights/Night Mode with Hazard
Lights)
[6] Grip Handle (Requires 4x AAA Batteries)
[1] Power Output Mode
[2] Drag Brake Mode
[3] Pistol Grip Battery Level
[4] Current Model Name
[5] Model Battery Level
[6] Light Mode
[7] Gear Display
[8] Quick Trim 1
[9] Quick Trim 2 Quick Start Steps:
1. Power on the pistol grip
2. Remove the model shell and connect battery
3. Briefly press button on receiver, light flashes 3 times
then stays solid
4. When model voltage shows on menu display screen,
you can control the model
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Features
Product Information
Specifications
115mm
162mm
180mm
320mm
130mm
60° 50°
Model Crawler
• Scale: 1/18 Full Simulation Structure
• Dimensions: 320*162*130mm(L*W*H)
• Weight: 850g (Battery Excl.)
• Wheelbase: 180mm
• Track Width: 150mm
• Shock Travel: 13mm
• Ground Clearance: 33mm
• Approach Angle: 60°
• Departure Angle: 50°
• Tires: φ 64mm
• Motor: 180 Custom High-Speed High-Torque Motor
• Esc: 3-in-1 10A 3 Channel Integrated Control Esc
• Battery: 1200mah 7.4V 5C Explosion-Proof Battery
• Charging Time: ≥2 Hours (Slow Charge) |
≥10 Minutes (14A Fast Charge)
• Color: Desert Brown / Sky blue / Meteorite Gray
Pistol Grip
• Frequency: 2.4ghz
• Operating Range: ≤200 Meters
• Operating Time: ≥40 Minutes
• Transmit & Receive
Model Appearance
• Tough Off-Road Styling Exterior Design
• High-Strength and Tough Abs Shell Material
• Spare Tire Design
• Tactical Low Visibility Coatings
Chassis System
• Highly Simulated Non-bearing Portal Axle Four-Wheel Independent Suspension System
• Open Modular Chassis Structure with Quick Maintenance Ports, Full Modular Quick Disassembly Design
• Full Simulated Ball Head Linkage Mechanism, Modular High Transmission Efficiency
Planetary Gearbox Mechanism
• 1.2mm High-Strength Stainless Steel Beams
• Simulated Wheel Edge Reduction Mechanism
• Front Wheel Anti-Ackermann Angle Design
• Integrated High-Strength Nylon Material, Structure Reinforcement, Shockproof and Drop
Resistant
Material Technology
• Mim Process High-Strength Silent Stainless Steel Gear Set
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Safety Instructions
Thank you for purchasing FrSky product.
This guide aims to help users properly operate, maintain and repair this product. Since most of
the parts used in this product are custom parts, please keep this manual for future reference.
This product is not a toy grade product, so it is not suitable for use by children under 14 years old.
Minors should be accompanied by adults when operating. Failure to operate or maintain this
product safely may result in personal injury. It is the owner’s responsibility to operate this product
safely. FrSky and its distributors are not responsible for any and all personal injuries and/or
property damage caused by use of this product.
Usage Guide
• Full Metal Custom Cvd Drive Shaft
• Precision Machined Stainless Steel Ball Head Screws
• 24mm Extra Wide Hollow Rubber Crawler Tires
• Universal 1.5mm Hex Screws for the Entire Crawler
Electronic Configuration
• Three-Speed Three-Mode Intelligent Esc Control
• Headlights, Taillights, Turn Signals, Spotlights with Simulated Linkage to Steering and Throttle,
Adjustable in Three Modes
• Real-Time Adjustable Esc Start Strength and Brake Force
• Monochrome 1.8 Inch Lcd Pistol Grip Screen
• On-Board 1200mah 7.4v 5c Large Capacity Explosion-Proof Battery
Warnings
• Please use genuine parts to replace damaged parts.
• Pay special attention to the positive and negative polarity of all wiring connections.
• Be sure to choose an appropriate environment to operate the product, the selected environment
should be away from cables, radio towers, waters and unstable terrain. The operator of product
is fully responsible for behavior.
• This product consists of delicate electronic components, do not expose it to damp environments
or other pollutants to avoid damage.
• Make sure to check the wireless reception range of the model crawler before each operation to
prevent loss or interference of the wireless signal.
• Operate this product within your abilities. At any time, if the model crawler operation is dangerous,
it is absolutely not worth the risk.
• Power on method: Be sure to turn on the pistol grip first before powering on the model crawler.
Power off method: Be sure to power off the model crawler first before turning off the pistol grip.
Reversing the above sequence may cause the model crawler to go out of control, resulting in
personal injury or property damage.
• Do not operate the model crawler when the pistol grip batteries are low to avoid loss of control.
• The plastic parts on the product are prone to deformation or damage due to extreme cold or hot
weather conditions. Therefore, please store the product in a room temperature environment with
controlled climate, and avoid placing the product near any heat sources such as ovens or heaters.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Safety Information
Prohibitions
Radio System
Carefully read the following symbols and related instructions. Failure to follow the guidelines
below may result in equipment damage or injury/loss of life.
Safety Symbols
If not operated according to the instructions, the operator or others may suffer minor injury.Caution
If not operated according to the instructions, the operator or others may suffer serious injury.Warning
If not operated according to the instructions, serious injury or even danger to the life of the operator or others
may occur.
Danger
Please read this manual carefully before use. We are not responsible for any deliberate
damage or improper use. This product is not a toy! It is recommended for ages 14 and
up. Users under 14 years old need adult supervision when using. This product contains
small parts, please ensure that children under 3 years old do not have access to this product.
• Do not use this product at night or during thunderstorms, as adverse weather may cause the
malfunction of the control equipment.
• Do not use this product in low visibility conditions.
• Do not use this product in in rainy, snowy, or wet conditions. Entry of liquids into the system
may result in unstable operation or malfunction.
• Signal interference may cause equipment to go out of control. For the safety of yourself
and others, do not use this product in the following locations:
1. Near base stations or other radio-active areas.
2. Crowded places or near roads.
3. Water areas with passenger vessels.
4. Near high-voltage power lines or communication broadcast antennas.
• Do not operate this product when feeling tired, uncomfortable, or under the influence of alcohol
or drugs causing anesthesia or excitement. Failure to comply may cause serious harm to
yourself or others.
• The 2.4GHz radio band is completely different from the low-frequency radio bands. When
in use, please ensure the model crawler is within line of sight, as large obstacles can
block radio frequency signals, leading to the loss of remote control and the model going
out of control.
Overview
[1]
[2]
[13]
[15]
[9]
[10]
[11]
[14]
[12]
[3]
[4]
[5]
[6]
[8]
[7]
Pistol Grip
The system adopts a 2.4GHz dedicated RF protocol for ground remote control devices, supporting
signal control and telemetry bidirectional data transmission. It can be used with many FrSky ground
receivers. The receiver included with this product supports 4 channels of control signal output, 6
channels of LED light control signal, and a single motor control port.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
[7] Power Switch
[8] Menu Down Navigation Switch Button
[9] Menu Up Navigation Switch Button
[10] Enter Button
[11] Trim Lever (Steering Center Adjustment)
[12] Trim Lever (Throttle Center Adjustment)
[13] Menu Display Screen
[14] Firmware Upgrade Port (Requires Upgrade
Accessory)
[15] Wrist Strap Hole
[1] Steering Wheel (CH1)
[2] Throttle Trigger (CH2)
[3] 3-Position Switch
(Left/Center/Right: High/Medium/Low Speed)
[4] 3-Position Switch
(Left/Center/Right: SPORT/CRAW/NORMAL Mode)
[5] Light Control Button (Day Mode/Night Mode/Night
Mode with Top Spotlights/Night Mode with Hazard
Lights)
[6] Grip Handle (Requires 4x AAA Batteries)
•
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Receiver
Overview
Receiver Functions & LED Signal Indicator Description
[1]
[7]
[6]
[5]
[4]
[3]
[2]
SIG
Antenna
Upgrade
+AIN
L1
L2
L3
BAT
L4
PWR/
Bind
L5
L6
CH4
CH3
CH2
CH1
MOT
[8]
[9]
[12]
[13]
[11]
[10]
[8] Battery Port
[9] Motor Port
[10] Power Switch/Binding
[11] LED Signal Indicator
[12] Antenna
[13] Upgrade Port
[1] Reserved Port
[2] Top Spotlights
[3] Brake Taillights
[4] Right Turn Signal
[5] Left Turn Signal
[6] Front Headlights
[7] Pwm Channel
• Short press Bind/PWR button to turn on: Indicator flashes 3 times to complete startup
• Hold Bind/PWR button for about 2 seconds to turn off: Indicator flashes 3 times to complete
shutdown
• Double click Bind/PWR button to bind: Indicator is in rapid flash state
• Off: No communication state
• Solid On: Normal communication state
• Flashing Rapidly: Binding in progress
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Battery Type: 4x AAA batteries
Battery Installation: Please follow the battery installation guide, insert left 2 batteries with positive
pole facing inwards and right 2 batteries with positive pole facing outwards.
Low Voltage Alert for Pistol Grip: When voltage drops below 4.5V, the display screen starts flashing
to alert user to replace batteries.
Low Voltage Protection for Model Crawler: The low voltage protection is preset to 6.5V out of
factory. When model crawler battery drops below 6.5V, ESC power supply is automatically cut off
(CH2), while steering (CH1) remains powered. At the same time, the hazard lights automatically
turn on and flash steadily (turn signals flashing, other lights do not flash). (Note: Under the low
voltage warning, resetting the low voltage protection value will not take immediate effect because
the system recognizes the current protection setting value.)
Quick Start Guide
Re-binding
Pistol Grip Battery Installation & Low Voltage Alerts
1. Open battery cover at bottom of pistol grip, install 4xAAA batteries as shown
Quick Start Steps:
1. Power on the pistol grip
2. Remove the model shell and connect battery
3. Briefly press button on receiver, light flashes 3 times
then stays solid
4. When model voltage shows on menu display screen,
you can control the model
1. Turn on pistol grip by long pressing power button.
2. Receiver will automatically bind with pistol grip when battery is connected.
3. During ground testing, if there is a situation where the model crawler deviates in a straight line,
use [Steering TRIM] on pistol grip to adjust steering center for correction.
1. Power on receiver, double click Bind/PWR button to put receiver into binding mode (receiver
indicator flashes rapidly).
2. Go to page 4/6 of pistol grip menu, select [Bind] under Receiver menu and press [Enter] to
put pistol grip into binding state.
3. Receiver indicator will solid on, press [Enter] to exit binding mode, re-binding complete.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Calibrate Throttle and Steering Channels
Failsafe Protection Description
1. Ensure receiver and pistol grip are in normal communication state.
2. Enter [Check] mode of [Device] on pistol grip.
3. Push throttle trigger fully forward and hold for 1s, then fully back and hold for 1s to record
channel range.
4. Turn steering wheel fully left and hold for 1s, then fully right and hold for 1s to record channel range.
5. Channel range recording is complete after exiting [Device Check] mode.
6. Restart pistol grip and receiver to complete calibration.
Servo Travel Adjustment
1. Ensure receiver and pistol grip are in normal communication state.
2. Go to page 1/6 of pistol grip menu, adjust following menu items to change servo travel, press
[Enter] after setting to save:
[Dual Rate] Adjust both side travel / [Left] Adjust single left side travel / [Right] Adjust single
right side travel
This function is enabled by default on pistol grip.
Go to page 4/6 of pistol grip menu, supports enabling/disabling this function.
When this function is triggered, throttle and steering simultaneously return to center position.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Th & Brake 2/8
Channel CH2
REV Normal
Rate
TH
Pistol Grip Inactivity Alerts
Channel CH1
Rev Normal
DR
Left 48%
Steering 1/8
Steering Setting
Throttle & Brake Setting
Right 48%
TRIM L1
SubTrim r1
Steering 1/8
MDL 1 VOL 8.4V
Light off G L
T1：ST T2：ST
TRIM S.TRIM
PTO N 6.0VDB 0
• If no operation for >20s, LCD backlight automatically turns off.
• If no operation for >20min, pistol grip automatically powers off.
Main Menu Introduction
[1] Power Output Mode
[2] Drag Brake Mode
[3] Pistol Grip Battery Level
[4] Current Model Name
[5] Model Battery Level
[6] Light Mode
[7] Gear Display
[8] Quick Trim 1
[9] Quick Trim 2
Steering channel cannot be configured (CH1)
Steering channel direction: Normal/REV (Reverse)
Total steering travel output, default 100%
Left-side steering travel output
Right-side steering travel output
Steering servo center trim adjustment
(Center trim adjustment when driving after
model is on the ground)
Steering servo mechanical deviation trim adjustment
(Steering deviation correction before model is
on the ground, using SubTrim)
Throttle channel cannot be configured (CH2)
Throttle trigger direction
NORMAL: Standard REV: Reverse
Throttle/brake total output rate, default 100%
Throttle output percentage, default 100%
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
ESC Setting
ESC Setting 3/8
ESC Mode For-Br-Rev
Bat Protection 6.5V
TH Interval 3
NORMAL
Forward Reverse Reverse Forward
REV
Th & Brake 2/8
REV Normal
Rate
TH
BK Brake output percentage, default 100%
FOR-BR-REV: Forward-Brake-Reverse (NORMAL Mode)
FOR-REV: Direct Forward-Reverse (CRAW Mode)
FPR-BR: Forward with brake (SPORT Mode)
Model low voltage protection threshold
(Default 6.5V)
Users can set it according to the battery
type, and it is recommended not to go
below 6.4V. After triggering the low voltage
protection, the motor power is automatically
cut off, the steering servo remains powered,
and the model's turn signals automatically
activate the Hazard Light mode. The display
screen will blink synchronously as a reminder.
At this point, the battery needs to be replaced.
After modifying the low voltage protection
threshold option parameters, the receiver
needs to be restarted.
Trigger midpoint, parameter range 0-10, adjust
the response interval of the throttle trigger
midpoint. Parameter 0 represents the
minimum interval with the highest sensitivity,
while 10 represents the maximum interval with
the lowest sensitivity.
After the pistol grip is powered on, double
-click the [BIND] button, the receiver's
signal indicator will flash rapidly. The
pistol grip menu enters [BIND] mode, a
binding prompt appears, keep this prompt
displayed for about 3 seconds, the
receiver's signal indicator will change from
flashing to solid on, indicating the
completion of binding. Short press the
[ENTER] button to exit, then long press the
[ENTER] button to return to the main
interface. At this point, the model's battery
voltage will be displayed, indicating that
the receiver has communicated with the
pistol grip. Restart the receiver and the
pistol grip to complete binding.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Receiver 4/8
MDL 1
Receiver [Bind]
Failsafe ON
Receiver Setting
Fail-Safe Protection
Switchable model with 5 sets of different
parameters
The set parameters will be automatically
saved to the corresponding model number.
Receiver Binding
Default enabled. After triggering fail-safe
protection due to signal loss, the throttle
and steering automatically return to
center position.
Calibration Steps:
- 1: Before entering calibration mode, do not operate the throttle trigger and steering wheel , check
if they have returned to the neutral position.
- 2: After confirming throttle trigger and steering wheel are centered without any interference, enter
[CHECK] mode, a prompt will appear.
check
Radio Setting 5/8
BackLight Time 2 S
ECO ON
Poweroff Min
Device
Radio Setting
Throttle trigger and steering wheel calibration
(calibrated at the factory). If there is an issue
with inconsistent throttle trigger or steering
wheel travel range, please calibrate manually.
Energy-saving mode backlight duration,
default 20 seconds.
Energy-saving mode switch, default ON,
turn OFF to keep backlight always on.
Automatic shutdown trigger time for inactivity,
range 1-30min. Pistol grip will automatically
power off based on threshold if no operation
detected. After pistol grip auto shut down,
receiver enters low power sleep mode, will
shut down automatically if no signal received
for over 10mins.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
PTO Setting 6/8
Output Mode NORMAL
Drag Brake 1
Start Strength 1
ESC Mode For-Br-Rev
PTO Setting
- 3: Following prompt instructions, turn steering all the way left to limit and hold 2 seconds, release
wheel. When stationary, turn all the way right to limit and hold 2 seconds, release wheel. Pull
throttle trigger all the way back to limit, hold 2 seconds, release trigger. When stationary, push
throttle trigger all the way forward to limit and hold 2 seconds, release trigger. Press [Enter] to
exit prompt menu, restart pistol grip, calibration completed.
Note: When calibrating throttle trigger and steering wheel, do not forcefully press on
limits. If single calibration unsuccessful, retry. If unsuccessful after multiple
attempts, needs factory repair.
3 groups of preset power output modes:
NORMAL/SPORT/CRAW
Controlled by SW2 button, custom drag brake
force and start strength.
Default ESC output mode in NORMAL/SPORT
is forward/reverse with brake, while in CRAW,
it is directly forward and reverse.
In this mode, the Drag Brake and Start
Strength parameters can be dynamically
adjusted in real-time with the DT quick adjust-
ment button.
When switching to any mode using the SW2
button, the parameters set with DT button will
be automatically saved, without needing to re-
tune each time, for fast precision adjustments
based on power output and stance.
The ESC operating mode is consistent in
NORMAL/SPORT, while CRAW is an
independent mode. When modifying
parameters, please first set the SW2 button to
the corresponding position before entering the
ESC mode.
Drag Brake: After the throttle trigger returns to
the center, the ESC automatically applies
brake force to keep the model stationary.
0-10 is drag brake force, 0 for natural coasting,
10 for maximum drag brake force.
0-10 is motor start strength, 0 for a natural curve
at the starting point, providing a gentle start from
a standstill. 10 for maximum start strength,
causing an instant increase in the initial torque
of the motor during startup, compensated by
software.
ESC mode setting: For-Br-Rev / For-Br / For-Rev
Note: With this function, recommended to
first select Output Mode and switch
to respective mode before changing
parameters to avoid confusion.
Changes take effect after long
pressing [Enter] to return to main
menu.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Gear Box 7/8
HIG SPEED
MID SPEED 7
LOW SPEED 4
R SPEED 4
Gear Box Electronic Transmission Setting
High-Speed Gear Speed Adjustment
Mid-Speed Gear Speed Adjustment
Low-Speed Gear Speed Adjustment
Reverse Gear Speed Adjustment
Custom three-speed gearbox: HIG High-Speed / MID Mid-Speed / LOW Low-Speed /
R Reverse
This model crawler model supports 5 working modes: Default / Day / Night / Spotlight / Hazard
Lights mode.
Single click on the light control button allows for the switching of lighting modes. (Note: Rebooting
pistol grip does not retain the last set lighting mode.)
1. Default Mode: All lights turned off
2. Day Mode: Steering and turn signals linkage, reverse and brake lights linkage
3. Night Mode: Headlights on, steering and turn signals linkage, taillights are dimly lit, reverse and
brake lights linkage
4. Spotlight Mode: Works under night mode while keeping top spotlights on
5. Hazard Light Mode: Works under spotlight mode while keeping hazard lights on
Light Control System Description
Gear shifting is controlled by the SW1 button, from left to right: High/Mid/Low 3 gears,
also displayed synchronously on screen. You can defines the max motor RPM caps in
each custom mode and freely set the maximum value according to actual usage. Chang-
ing max values will not affect the linear curve of the throttle trigger. but the power output
in low gears will have a broader range of throttle trigger travel matching, providing more
delicate linear control. R is the reverse gear, it is proportional fixed ratio of total power
output regardless of H/M/L selection.
DT Setting
DT Setting 8/8
T1 ST
Object TRIM
T2 ESC
Object DB
T1 T2 Quick Trim Customization
ST: Steering
DR: Direction Range
TRIM: Center Trim
SUBTRIM: Mechanical Deviation Trim
TH: Throttle
RAT: Throttle/Brake
Total Output Rate
ESC: Electronic Speed Control
DB: Drag Brake Force
SF: Start Force (Start Strength)
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Battery Usage Notes
Model Crawler Settings
Battery Connect
Step 1: Remove the model shell
Step 2: Place battery in battery compartment
Step 3: Connect battery plug
Note:
1. Unplug batteries for long term storage to prevent damage.
2. Do not open, disassemble or attempt to repair batteries.
3. Disconnect batteries from model before charging.
4. Do not charge batteries inside the model.
• Do not use Nicd, NiMH or any other type of charger to charge LIPO lithium polymer batteries.
Please use dedicated chargers to charge LIPO lithium polymer batteries.
• Do not charge unattended.
• Do not overcharge batteries.
• Do not charge batteries on flammable or heat-sensitive surfaces.
• Always use safety bags or containers when charging batteries. Ensure batteries do not overheat
at any time. Battery temperatures exceeding 140°F (60°C) can cause damage or even lead to a fire.
• Do not leave batteries installed in model long term, and never charge batteries inside models.
• Do not drain/discharge batteries to avoid damage.
• Do not expose the batteries to water or moisture at any time.
• Do not store batteries near open flames or heaters.
• Do not mix with other assembled or pre-assembled batteries.
• Batteries must be stored in a safe location out of reach of children.
• Remove battery immediately if model suffers any impact.
• Even in the case of minor damage, carefully inspect the batteries and connectors.
• Note: Batteries may heat up after use, allow to cool down to room temperature before charging.
• Avoid contact of electrolyte with eyes or skin. If electrolyte comes into contact with any part of
the body, wash immediately.
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
• Do not replace or modify battery pack connectors or wires.
• Check the battery condition before charging or any other operation.
• Do not short circuit batteries.
• Do not directly touch leaked or damaged batteries.
• Do not charge batteries beyond the recommended temperature range (0°- 45°C Celsius).
The product may be used freely in these countries: Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal,
Greece, Ireland, Denmark, Luxembourg, Austria, Finland, Sweden, Norway, Switzerland, France and Iceland.
CE
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Instruction Manual for FrSky "Edge Warrior" 1/18 RC Crawler
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Table of contents
