FrSky FLD-02 User manual

www.frsky-rc.com
2011/0 9 / 09
Instruction
Instruction
Instruction
Instruction Manual
Manual
Manual
Manual for
for
for
for FrSky
FrSky
FrSky
FrSky FLD-02
FLD-02
FLD-02
FLD-02
1
1
1
1 Introduction
Introduction
Introduction
Introduction
1.1
1.1
1.1
1.1 Specifications
Specifications
Specifications
Specifications
Model: FLD-02
Compatibility: FrSky DFT, DJT and DHT
Dimension: 55*40*12 mm
Pixel: 128*64
1.2
1.2
1.2
1.2 Features
Features
Features
Features
1) Show all connected sensors data;
2) Capable of programming alarm thresholds and directions.
3) Firmware upgradable .
2
2
2
2 Installation
Installation
Installation
Installation
Connect FrSky FLD-02 to the UART and power connection on FrSky telemetry module (Rxd, Txd,
+5V, GND) by the provided cable. Confirm the orientation is correct and make sure both switches
on the telemetry module are OFF.
3
3
3
3 Screen
Screen
Screen
Screen Structures
Structures
Structures
Structures
3.1
3.1
3.1
3.1 Main
Main
Main
Main Screen
Screen
Screen
Screen
FrSky Logo
Version Number
Data Screen
Menu Screen
FrSky Website
3.2
3.2
3.2
3.2 Menu
Menu
Menu
Menu Screen
Screen
Screen
Screen
Blade: Blade Number
Volt ratio: A1 & A2 Voltage Division Ratio
Unit Set: Speed (m/s or MPH)
Temperature (Celsius or Fahrenheit)
Altitude (M/Foot)
Alarm Set: A1_1/2, A2_1/2, RSSI_1/2
Note:
Note:
Note:
Note: Make
Make
Make
Make sure
sure
sure
sure the
the
the
the battery
battery
battery
battery voltage
voltage
voltage
voltage division
division
division
division ratios
ratios
ratios
ratios are
are
are
are programmed
programmed
programmed
programmed in
in
in
in accordance
accordance
accordance
accordance with
with
with
with
those
those
those
those of
of
of
of connected
connected
connected
connected battery
battery
battery
battery voltage
voltage
voltage
voltage sensors.
sensors.
sensors.
sensors.
The alarm thresholds and directions (either above or below threshold) can be programmed. After
alarm thresholds and directions are programmed, click “ OK ” . ” √
√
√
√” means these values have been
remembered by the module.
Below are FrSky default values for RSSI, users can change according to their requirements:
Alarm Than Value
RSSI 1 ＜45
2＜42

www.frsky-rc.com
2011/0 9 / 09
3.3
3.3
3.3
3.3 Data
Data
Data
Data Screen
Screen
Screen
Screen
3.3.1.
3.3.1.
3.3.1.
3.3.1. Screen-1
Screen-1
Screen-1
Screen-1
GMT (H/M/S)
Fuel Level
A1 & A2 Voltage
Temperature 1 & 2
R x RSSI & T x RSSI
3.3.2
3.3.2
3.3.2
3.3.2 Screen-2
Screen-2
Screen-2
Screen-2
Altitude
RPM
Speed
Rate
Ampere
3.3.3
3.3.3
3.3.3
3.3.3 Screen-3
Screen-3
Screen-3
Screen-3
Total Voltage
Voltage for each cell
Note:
Note:
Note:
Note: Screen-3
Screen-3
Screen-3
Screen-3 shows
shows
shows
shows up
up
up
up only
only
only
only when
when
when
when FrSky
FrSky
FrSky
FrSky Lipo
Lipo
Lipo
Lipo Voltage
Voltage
Voltage
Voltage Sensor
Sensor
Sensor
Sensor (FLVS-01)
(FLVS-01)
(FLVS-01)
(FLVS-01) is
is
is
is connected,
connected,
connected,
connected,
otherwise
otherwise
otherwise
otherwise Screen-4
Screen-4
Screen-4
Screen-4 will
will
will
will show
show
show
show up
up
up
up after
after
after
after Screen-2.
Screen-2.
Screen-2.
Screen-2.
3.3.4
3.3.4
3.3.4
3.3.4 Screen-
Screen-
Screen-
Screen- 4
4
4
4
Acceleration X/Y/Z
Longitude & Latitude