FS SpeedFlow Wireless Eco Wave User manual

SpeedFlow Wireless Controller Eco
Wave v3.1x
Technical specifications
Duration of continuous operation approx. 84 hours with 2x Duracel Industrial AAA
Survival time in standby approx. 9 months
Power consumption when OFF Real power separation. No consumption
Power consumption on standby approx. 200 µA
Power consumption in operation approx. 16 mA
operating manual
Setting the channel to be used and connecting to the receiver
Switch off the controller. Select the desired channel on the Carrera receiver. Hold down the switch
button on the controller while switching on. The receiver acknowledges the programming with the “7-
segment round trip”. Controller ready to go.
Activation of the configuration mode
The controller has already been connected to the receiver. Switch off the controller. Hold down the
throttle fully and hold down the turnout button and then switch on the controller. LED goes on. After
releasing the switch button and the trigger, the configuration begins.
The configuration is based on the SpeedFlow Box programming
The desired configuration value is selected by briefly pressing the switch button. The selected value
is saved by holding down the switch button until the LED flashes quickly to confirm the saving. then
the next configuration option is displayed by flashing. The following configuration options are
available.
Number of speed levels
·1 x flashing - original Carrera 16 speed steps
·3 x flashing - Speedflow control 30 speed steps
·4 x flashing - Speedflow control 44 speed steps

Selection: short press
Save: long press until LED flashes quickly.
Launch Control active or switched off
·1 x blinking deactivated
·2 flashes Launch Control is available
Selection: short press
Save: long press until LED flashes quickly.
Select power curve
The translation of the trigger position into the power level of the car can be set here. The number of
flashes indicates which curve is selected.
Selection: short press
Save: long press until LED flashes quickly.

·1 linear
·2 and 3 more sensitive dosing possible in the medium speed range, powerful acceleration
and strong influence at the end of the control range
·4 and 5 more sensitive dosing possible in the high speed range and a powerful start even
with little pressure
·6 and 7 more sensitive dosing possible in the low speed range
Select the trigger position from which the car
starts
You can also check the current position. If the trigger is on less gas than at which the car would
actually start driving, the LED is off. If you press it further than the starting point, the LED lights
up. The new starting position is set by holding the trigger in the desired position and pressing the
switch button for a long time until the LED acknowledges the storage with rapid flashing.
Set the trigger position from which the car
drives at full throttle
It is best to choose a position just before “fully depressed”. The check of the set full throttle position
is identical to the check of the start position. If the trigger is pressed less, the LED does not light up,
if it is pressed further, it is on. The new starting position is set by holding the trigger in the desired
position and pressing the switch button for a long time until the LED acknowledges the storage with
rapid flashing.
Programming completed
Programming can be terminated prematurely at any time by switching off the controller. Only values
that have already been acknowledged are changed.
Reset to default settings
Switch off the controller. Hold down the trigger and turnout button when switching on and continue to
hold both down for about 10 seconds. The controller acknowledges the reset after approx. 8
seconds with a steady flashing signal. Now the controller can be switched off and on again. It has
been reset to the factory settings. Then it has to be trained again on the desired receiver.
For the configuration, the controller must first be connected to the receiver and the receiver must be
active during configuration.
When switching on, the number of flashing signals tells you which channel it is programmed on.
If the controller is active, the LED flashes at regular intervals. The more empty the batteries are, the
more often the LED flashes. If batteries are in use, think about replacing the batteries at 2-3 flashes
per second. When using rechargeable batteries, charging should be considered at one flash per
second, otherwise the batteries can be deeply discharged. The controller is only switched off at
1.8V.

Standby / power saving mode
After 5 minutes of inactivity, the controller goes into sleep mode. This reduces power consumption to
an eightieth. So it is not so bad if you forget to switch off.
How do I find out which channel my controller
is currently programmed on?
Simply count the slow flashing signals when switching on. The number corresponds to the channel
number
Why does my controller only react 2-3 seconds
after switching on?
After switching on, the controller only shows its channel number by flashing signals. Only then is it
ready to go.
How do I wake up the controller from sleep
mode (power saving mode)?
In order to enable this strong reduction in power consumption, it was not necessary to query the
throttle in sleep mode. As a result, only pressing the switch button will wake the controller up again.
Alternatively: switch it off and on again.
Subject to technical changes - as of November 2015
Carrera is a registered trademark of Stadlbauer Marketing + Vertrieb GmbH in Puch / Salzburg
Austria
frankenslot is a registered trademark of the Slotcar Factory Cadolzburg Germany