FS FS-S036-2IO-24F User manual

24 FIBER OPTICAL SPLICE CLOSURE
24-FASER LWL-SPLEIßKASSETTE
BOITIER D'ÉPISSURE OPTIQUE 24 FIBRES
V1.0
Quick Start Guide
Quick Start Anleitung
Guide de Démarrage Rapide

Introduction
Accessories
Thank you for choosing the fiber optical splice closure (FOSC) & fiber optical splice tray (FOST). This
guide is designed to familiarize you with the layout of the FOSC&FOST and describes how to deploy
them in your network.
FS-S036-2IO-24F
CE-24F-FS
EN
1
Hang Hook x2Plastic Sleeve x1Insulation Tape x1 M6 Special Wrench x1

Installation Requirements
Heat Shrinkable
Protective Sleeve x24
Built-in Splice Tray Nylon Tie x10
Seal Tape x1
EN
2
To ensure the technical requirements, the following instructions must be
followed:
The fibers in the FOST are spliced and installed orderly.
The curved diameter of fiber meets with the technical requirements.
The internal tighteners are tightened.
The inlet/outlet ports without fiber cables must be blocked up with the port plugs.
Control the amount of seal tape within a proper range.
Seal fitting is installed neatly and smoothly.
M4 Screw x2 M4 Nut x2 Labeling Paper x4
1 2 3 4 5 6
1 2 3 4 5 6

Installation
Unscrew fixing bolts and open the closure by lifting the unscrewed bolts with no need completely
unbolting to avoid loosing.
Open the Closure
NOTE: If the weather condition is not good enough, then a tent must be pitched for
waterproof and dustproof.
EN
3
Loacting bolt
Optical cable pressure block
Fixing bolt
Fixing bolt
Fixing bolt
Fixing bolt
Fixing bolt
Fixing bolt
Fixing bolt
Fixing bolt
Loacting bolt
Optical cable pressure block

Determine the Length of Fiber Cable
1. Fiber cable in 50mm length: the distance from seal fitting to fiber cable pressboard.
2. Fiber cable in 2020mm length: it is used to be winded and spliced after stripping.
3. Fiber with protective coat in 420mm length: the distance from the fixing point of fiber cable to the
fixing point of FOST (fiber optic splice tray).
4. Fiber in 1600mm length: after stripping off the protective coat, it is to be winded inside the FOST
after splicing with other fibers.
EN
4
Fiber cable
Temp
locating mark
50mm sealing and fixing length of fiber cable inside FOSC
2020mm length of protective coat of fiber cable to be stripped off
420mm length of fiber with protective coat
(the distance from fixing point of fiber cable to fixing point of FOST)
1600mm length of protective coat of fiber to
be stripped off(to be spliced and winded with other fibers)
Strip off Fiber Protective Coat of Fiber Cable
Strip off protective coat of fiber cable from the temp locating mark with the cutter and the stripper,
please refer above for stripping length. Stripping length also could be decided according to
installation requirement.
NOTE: 1. Reserve enough length of fiber cable to be spliced.
2. Stripping length also could be decided by customers according to installation
requirement.
Temp locating mark
Cutter
Stripping terminal fiber cable
Fiber cable entry terminal

Separate Fiber Cores
1. Wind 2 layers of insulation tape on protective coat of fiber core. Meanwhile, get rid of the stuffing
to separate fiber core and clean them. Form a ring with the diameter of 100mm or so and fix it on the
fiber temporarily by adhesive tape.
2. This FOSC is provided with six inlet/outlet ports. Number of fiber cables is determined by the
customers according to their actual requirements and the corresponding number of port plugs
should be taken out. The max number of fiber cables to be installed is six.
3. This FOSC is suitable for the following diameters of fiber cables respectively:
Port A: suitable for fiber cable with max. external diameter ф16mm
Port B: suitable for fiber cable with max. external diameter ф16mm
4. The corresponding inlet/outlet ports are to be selected according to fiber cables actually installed.
When the diameter of fiber cable is smaller than that of the inlet/outlet port, then the sealing tape
should be used to enlarge the external diameter of fiber cable, of which the perimeter could be
measured by measuring paper marked by Hole A, Hole B, coming as accessories.
5. Reserve reinforced core in 40mm length and cut off the unnecessary ones.
EN
5
NOTE: If it is difficult to pull all the protective coat of fiber cable at one time, strip it off
section by section to avoid fiber breakage.
NOTE: 1. Before the seal tape is used for enlarging the fiber cable diameter, it should be
scratched and to be cleaned with abrasive cloth and ethyl alcohol.
2. Cut off reinforced core with a special cutting plier.
40
5-10
25 20
10
10
Adhesive tape
Fiber
Seal tape
Insulation tape
Reinforced core
Bunchy/ribbon fiber
(with protective coat)

EN
6
Fix Reinforced Core and Fiber Cable
1. Demount port plugs, pressboard and fixing nut of reinforced core.
2. Tighten fiber cable pressboard. If the diameter of fiber cable is not long enough, then enlarge it
with insulation tape.
3. Tighten nut of reinforced core with the special wrench (plastic) and then re-tighten it with the
metal wrench.(the metal wrench should be provided by operator).
Fiber cable
Housing
Fixing device for
fiber cable
Fixing device for reinforced core
Pressboard
Nut for reinforcesd
core
Fixing bolt for fiber cable
Fiber
NOTE: Make sure to check whether the fiber cable stripped fits in with the fixing ports
affect or not. If not, the adjustment should be done in time. Otherwise it will affect
installation quality.
Seal fitting

Install Heat Shrinkable Protective Sleeve and House fibers
When having completed splicing the fibers, the first fiber ring should be housed on the farthest side
of FOST, the remaining fiber should be winded, forming a ring with diameter not less than 80mm.
Then put it into FOST together with heat shrinkable sleeve for splice protection. ( Firstly fix heat
shrinkable protective sleeve into the slot, then enlarge the diameter of fiber ring properly.)
NOTE: Pay attention to the twist and bend of fiber.
Fiber Heat shrinlable
protective sleeve
Nylon tie
Right terminal fiber
with protective coat
Left terminal fiber with
protective coat
FOST
Fixing slot of heat shrinkable
protective sleeve(bunchy)
EN
7

Assemble FOSC Housing
1. Check up comprehensively.
2. Put the FOSC cover on the FOSC bottom directly.
3. Put two pieces of insert plates into the slot.
4. Insert two pieces of locating bolt of FOSC and tighten it with the special wrench.
5. If the FOSC is for aerial application, then put the hanging hook on one side of the closure and then
tighten fixing bolts on both sides. Otherwise tighten the four fixing bolts on 5.9.5 four corners
respectively.
Online Resources
Download
Help Center
Contact Us
https://www.fs.com/products_support.html
https://www.fs.com/service/fs_support.html
https://www.fs.com/contact_us.html
NOTE: Clean the housing and pay attention to the above sequence.
EN
8
Seal fitting
Fixing device
for reinforced core
Fixing slot of heat shrinkable
protective sleeve
Optical cable pressure block
Seal tap
Optical cable
pressure block
Fiber
Lock of FOST
FOST Port plug B
Terminal A fiber cable
Heat shrinlable protective sleeve
Cover of FOST

Zubehör
Einführung
Vielen Dank, dass Sie sich für die LWL-Spleißkassette FOSC und die Spleißablage FOST entschieden
haben. Diese Anleitung soll Sie mit dem Aufbau von FOSC und FOST vertraut machen und
beschreibt, wie Sie diese in Ihrem Netzwerk einsetzen können.
FS-S036-2IO-24F
CE-24F-FS
Aufhängehaken x2Kunststoffhülse x1Isolierband x1 M6 Spezialschlüssel x1
9
DE
FS-S036-2IO-24F
CE-24F-FS