FSR TM-IPAD-TR User manual

FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]
43036 LIT1452
1.50 1.50
1. REMOVE BASE COVER.
BASE COVER
(RETAIN FOR
REASSEMBLY) (2) COVER SCREW
(RETAIN FOR
REASSEMBLY)
2b. SWIVEL BASE MOUNTING:
MOUNTING HOLES ACCESSED
BY SWIVELING UNIT
(SEE BELOW)
RECOMMEND DRILLING
3/4 DIA. HOLE FOR
CABLE PASS-THRU
DRILL PILOT HOLES
FOR DIMENSIONED
HOLES AND TRANSFER
REMAINING HOLES FROM
BASE TO SURFACE.
DRILL 5/64 DIA. PILOT HOLES
FOR #8 SCREWS (SUPPLIED)
HOLE ACCESSIBLE
WHEN UNIT IS
SWIVELED 1.50 1.50
SWIVEL UNIT
COUNTER-
CLOCKWISE TO
ACCESS HOLE
2a. STANDARD BASE MOUNTING:
9 POSSIBLE MOUNTING
HOLES (RECOMMEND
3 MINIMUM), TRANSFER
PATTERN FROM BASE
TO SURFACE.
DRILL 5/64 DIA. PILOT HOLES FOR
#8 SCREWS (SUPPLIED)
IF REQUIRED DRILL 3/4 DIA.
HOLE FOR CABLE PASS-THRU
POSITION IPAD BETWEEN
TABS OF FRONT COVER
IPAD
FRONT
PANEL
REAR VIEW OF FRONT PANEL
6a. PLACE IPAD ONTO FRONT PANEL AND CONNECT CONNECTOR.
6b. REINSTALL FRONT PANEL AS SHOWN BELOW WHILE
HOLDING IPAD IN PLACE. SECURE WITH ORIGINAL SCREWS.
FRONT PANEL
IPAD (SUPPLIED
BY CUSTOMER)
CONNECT TO IPAD BEFORE
REASSEMBLY OF FRONT PANEL
ENSURE SWITCHES ARE PROPERLY
SET BEFORE REASSEMBLY OF
FRONT PANEL
USE PENCIL
(ERASER END)
TO ACTIVATE
POWER SWITCH
(4) COVER SCREW
INSTALL #6-32 NUT
(SUPPLIED) TO
DISABLE POWER
SWITCH LEVER
TM-IPAD-TR / TM-IPAD-TRS / TM-IPMINI-TR / TM-IPMINI-TRS INSTALLATION INSTRUCTIONS
3.46
MIN.
A
A
B
BC
C
NO SCREWS -
HOLE A -
HOLE B -
HOLE C -
180°
140°
104°
90°
INSERT #6-32 x 1/4 LG PAN-HEAD
SCREWS (SUPPLIED) TO
CORRESPONDING LETTERS TO
CHANGE SWIVEL RANGE
INSERT #6-32 x 1/4 LG
PAN-HEAD SCREW
(SUPPLIED) TO DISABLE
SWIVEL FEATURE
REMOVE COVER FOR
HORIZONTAL / VERTICAL
LOCKING OPTIONS
HORIZONTAL / VERTICAL
LOCKING OPTIONS
(ALL MODELS)
COVER
SHOWN
REMOVED
ROTATE IPAD HORIZONTALLY
OR VERTICALLY AND INSTALL
#6-32 x 1/2 LG PAN-HEAD
SCREW (SUPPLIED) IN
CORRESPONDING HOLE
FOR VERTICAL
LOCK POSITION
FOR HORIZONTAL
LOCK POSITION
BEFORE INSTALLING LOCKING
SCREWS, CENTER IPAD ON
BASE (AS SHOWN)
SWIVEL RANGE

4. REASSEMBLE BASE COVER.
BASE COVER
(2) COVER SCREW
5. REMOVE FRONT COVER.
ROUTE USB CONNECTOR (OR POWER
SUPPLY WIRING IF USING USB CHARGER KIT)
THRU COVER OR CABLE ACCESS HOLE
AS REQUIRED
FRONT COVER
(RETAIN FOR
REASSEMBLY)
(4) COVER SCREW
(RETAIN FOR
REASSEMBLY)
(4) COVER SCREW
FRONT COVER
6. REASSEMBLE FRONT PANEL WITH IPAD. EXPLODED VIEW FOR
REFERENCE. SEE BACK PAGE FOR FINAL ASSEMBLY.
IPAD (SUPPLIED BY CUSTOMER)
IPAD CONNECTOR (SUPPLIED)
USB CHARGER
SNAP-IN CONNECTOR
(USB CHARGER KIT
SOLD SEPARATELY)
SNAP-IN BRACKET
INCLUDED APPLE
CORD, USB END
SNAP-IN BRACKET
ASSEMBLY
SKIP TO STEP 4 IF NOT USING USB CHARGER
SNAP-IN CONNECTOR OPTION.
3.
3a. REMOVE SNAP-IN BRACKET.
SNAP-IN BRACKET
(INCLUDED)
#6 FLAT-HEAD SCREW
(RETAIN FOR REASSEMBLY)
3b. INSTALL USB CHARGER SNAP-IN CONNECTOR ONTO SNAP-IN
BRACKET. CONNECT USB END TO USB CHARGER.
3c. REINSTALL SNAP-IN BRACKET ASSEMBLY.
#6 FLAT-HEAD SCREW
ROUTE POWER SUPPLY WIRING THRU
CABLE PASS-THRU (RECOMMENDED) AND
MAKE NECESSARY TERMINAL CONNECTIONS
(SEE KIT INSTALLATION INSTRUCTIONS)
HIGHLY RECOMMENDED WIRES BE
ROUTED THRU CABLE ACCESS HOLE
FOR SWIVEL UNITS
WIRING STRAIN RELIEF
TIE WRAP HOLE