FSR HD-HWP-TX User manual
HD-HWP-TX
100m HDBaseT HDMI Extender Wallplate
244 Bergen Boulevard, Woodland Park, NJ 07424 Tel 973-785-4347 FAX
973-785-3318 Web: www.fsrinc.com
43152 LIT1599
User Manual
2
Important Safety Instructions
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
6. Clean this device only
with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that
produce heat.
5. Do not place sources of open
flames, such as lighted candles,
on the unit.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
at
p
lu
g
s.
9. Only use
attachments/accessories
specified by FSR.
10. Refer all servicing to
qualified service
personnel.
3
Table of Contents
Overview .................................................................................................. 4
Features ................................................................................................... 4
Cable Distances & Resolutions: ............................................................... 5
Typical Application.................................................................................... 6
HD-HWP-TX Dimensions ......................................................................... 7
HD-HWP-Tx Front Panel.......................................................................... 8
HD-HWP-Tx Rear Panel .......................................................................... 9
Hardware Installation.............................................................................. 10
IR and RS-232 Operation........................................................................11
IR Control.........................................................................................11
RS-232 Control ............................................................................... 13
Specifications ......................................................................................... 14
Limited Warranty .................................................................................... 16
4
OVERVIEW
The HD-HWP-TX transmitter is a true HDBaseT 5-Play device that transmits HD
Video (4K UHD), Audio, Bi-directional control (IR & RS-232), Ethernet, and Power
via 1 CAT-6A shielded cable up to 100 Meters.
The HD-HWP-TX works with any of FSR’s 100 Meter HDBaseT Receivers and
can be powered by any 100m Receiver or powered locally
The unit fits in a standard 2-gang box.
5
FEATURES
Supports 4K UHD / 2160p (3840 x 2160 or 4096 x 2160p @ 24Hz / 25Hz /
30Hz / 50 Hz / 60 Hz) (4:2:0 8-bit)
Supports an HDMI input
HDBaseT 1.0 compliance
HDMI 1.4 with 4K compliance
HDCP 2.2 pass-through
Bi-directional PoE (HD-HWP-TX only)
Bi-directional IR
IR, Ethernet and RS232 control over HDBaseT
Space saving design
CABLE DISTANCES & RESOLUTIONS:
CAT-5e / CAT-6:
100 Meters: 1080p @60 Hz (36 bpp)
70 Meters: 1080p @60 Hz (48 bpp) or 3D and 4K UHD / 2160p (3840 x 2160
or 4096 x 2160p @ 24Hz / 25Hz / 30Hz / 50 Hz / 60 Hz)
(4:2:0 8-bit)
CAT-6a / CAT-7:
100 Meters: 1080p @60 Hz (48 bpp) or 3D and 4K UHD / 2160p (3840 x 2160
or 4096 x 2160p @ 24Hz / 25Hz / 30Hz / 50 Hz / 60 Hz) (4:2:0
8-bit)
NOTE:
The actual signal transmission distance can vary and depends on signal
resolution, cable quality, graphics card, and display used in the system.
6
TYPICAL APPLICATION
HD-HWP-Tx shown
NOTE: Only one power supply is needed to power the Transmitter and Receiver
set from any of the FSR's 100m HDBaseT receivers. The HD-HWP-Tx transmitter
can be powered locally but it cannot send power to the receiver. Transmitters do
not include a Power Supply. An FSR 17762 Power Supply is included with any of
the FSR HDBaseT Receivers. FSR 17762 Power Supplies can also be ordered
separately.
Transmitter
An
y
FSR HDBaseT Receiver
HD-HWP-TX
7
HD-HWP-TX DIMENSIONS
IR SENSOR
HDMI HDCP Link
HD-HWP-Tx
HDMI
VIDEO
INPUT
ON
123
ETHERNET HDBT OUT
+12V
GND
+12V
GND
Tx
Rx
GND
IR+
IR-
IN OUT
POWER
RS-232 IR OUT
8
HD-HWP-TX FRONT PANEL
ID Name Description
1 HDMI VIDEO INPUT HDMI input connection from source
2 HDMI LED Indicates an active HDMI input
3 HDCP LED
On: HDCP video is being transmitted.
Off / Intermittent: No HDCP video is being
transmitted
4 Link LED
ON: Receiver and Transmitter are linked to
each other
OFF / Intermittent: Fault in unit(s) or cabling.
5 IR SENSOR Infrared Sensor window for remote control
1
5
3
2 4
9
HD-HWP-TX REAR PANEL
ID Name Description
1 POWER IN
12V 2A DC power supply input (power supply sold
separately. (See note under "Typical Application")
2 POWER OUT 12VDC 250mA max
3 RS-232 Serial port
4 IR OUT Connects to IR transmitter
5 ETHERNET Connects to an Ethernet device
6 HDBT OUT Connects to HDBT IN port of receiver
6
5
2
3
4
1
10
HARDWARE INSTALLATION
Warnings
Before the installation, disconnect the power supply from all the
devices.
Do not connect or disconnect cables from the Transmitter and
Receiver while they are powered ON. To connect or disconnect
cables from the units, power them OFF first.
For best resolution and ESD performance, a shielded CAT6A in a
TIA / EIA 568B wiring configuration is recommended. Please use
care when installing, connecting and disconnecting cables.
1. Connect the source to the HDMI IN on the Transmitter.
2. Connect the IR emitter to the IR OUT and the IR Receiver to the IR IN on
both the Transmitter and Receiver.
3. Connect a Display to the HDMI OUT on the Receiver.
4. Connect the HDBT OUT on the Transmitter to the HDBT IN on the Receiver
via a shielded CAT5e / CAT6 / CAT6A / CAT7 cable. (CAT6A shielded cable
is recommended for best performance.)
5. Connect the power supply.
11
IR AND RS-232 OPERATION
IR Control
The IR pass-through feature on the Transmitter and Receiver allows you to
control the Source from the Display’s location or vice versa.
Scenario 1
The TV can be controlled from the Transmitter’s location with the TV remote.
The IR receiver is connected to the IR IN on the Transmitter and the IR emitter is
connected to the IR OUT on the Receiver.
HDBT IN
ETHERNET
+12V
GND
+12V
GND
Tx
Rx
GND
IR+
IR-
IN OUT
POWER RS-232 IR OUT
HD-H-SP-Rx shown (ordered seperately)
HDBaseT
BLUE-RAY
DVD
TV
IR SENSOR
HDMI HDCP Link
HD-HWP-Tx
HDMI
VIDEO
INPUT
ON
123
TV REMOTE
IR EMITTER
CABLE
NORMAL
UPDATE
HDMI OUTTx Rx
IR OUTIR IN
+
-
DC 12V
-
+
ETHERNET
+12V
GND
+12V
GND
Tx
Rx
GND
IR+
IR-
IN OUT
POWER RS-232 IR OUT
12
Scenario 2
The DVD Player can be controlled from the Receiver’s location with the DVD
Player Remote. The IR emitter is connected to the IR OUT on the Transmitter and
the IR receiver is connected to the IR IN on the Receiver.
HDBT IN
ETHERNET
+12V
GND
+12V
GND
Tx
Rx
GND
IR+
IR-
IN OUT
POWER RS-232 IR OUT
HD-H-SP-Rx shown (ordered seperately)
HDBaseT
BLUE-RAY
DVD
TV
IR SENSOR
HDMI HDCP Link
HD-HWP-Tx
HDMI
VIDEO
INPUT
ON
123
TV REMOTE
NORMAL
UPDATE
HDMI OUTTx Rx
IR OUTIR IN
+
-
DC 12V
-
+
IR RECEIVER
CABLE
IR EMITTER
CABLE
13
RS-232 Control
The RS-232 port can be used as a pass-through to control a device connected to
the Transmitter from the Receiver or vice versa.
RS-232 Control
Maximum baud rate is 115.2 Kbps.
HDBT IN
ETHERNET
+12V
GND
+12V
GND
Tx
Rx
GND
IR+
IR-
IN OUT
POWER RS-232 IR OUT
HD-H-SP-Rx shown (ordered seperately)
HDBaseT
IR SENSOR
HDMI HDCP Link
HD-HWP-Tx
HDMI
VIDEO
INPUT
ON
123
NORMAL
UPDATE
HDMI OUTTx Rx
IR OUTIR IN
+
-
DC 12V
-
+
RS-232 DEVICE
RS-232 DEVICE
14
SPECIFICATIONS
Technical
Video input Connector 1 HDMI
Input Signal Types 4K UHD / 2160p (3840 x 2160 or 4096 x 2160p
@ 24Hz / 25Hz / 30Hz / 50 Hz / 60 Hz (4:2:0
8-bit) 7.1ch audio
HDMI 1.4 and HDCP compliant
Output 1 HDBT
Output Signal Type HDBT
Video Impedance 100Ω
Control
Control input RS-232 via 3.81mm 3 Pin pluggable screw
terminal Connector
IR input via sensor on front panel
IR output via 3.81mm pluggable screw terminal
Maximum Pixel Clock 297MHz
Operating Temperature 32°F to 95°F (0°C to 35°C)
10% to 90%, non-condensing
Storage Temperature -4°F to 140°F (-20°C to 70°C)
10% to 90%, non-condensing
Power Supply DC 12V 2A (power supply sold separately)
ESD Protection Human-body Model:
±8kV (Air-gap discharge)
±4kV (Contact discharge)
Surge Protection IEC 61000-4-4 (EFT) 40A (5/50ns); IEC
61000-4-5 (Lightning) 25A (8/20μs)
15
Cable Specifications
For best resolution and ESD performance, Shielded CAT6A in a TIA / EIA
568B wiring configuration is recommended.
CAT-5e / CAT-6:
100 Meters: 1080p @60 Hz (36 bpp)
70 Meters: 1080p @60 Hz (48 bpp) or 3D and 4K UHD / 2160p (3840 x
2160 or 4096 x 2160p @ 24Hz / 25Hz / 30Hz / 50 Hz / 60
Hz) (4:2:0 8-bit)
CAT-6a / CAT-7:
100 Meters: 1080p @60 Hz (48 bpp) or 3D and 4K UHD / 2160p (3840 x
2160 or 4096 x 2160p @ 24Hz / 25Hz / 30Hz / 50 Hz / 60
Hz) (4:2:0 8-bit)
NOTE:
The actual signal transmission distance can vary and depends on
signal resolution, cable quality, graphics card, and display used in the
system.
General
Shipping
Weight
1.45 lbs. (0.66 kg)
Dimension
(W x H x D)
3.58"W (90.9 mm) x 4.09"H (103.9 mm) x 1.45"D (37.8 mm)
16
LIMITED WARRANTY
The HD-HWP-TX Extenders are warranted against failures due to defective parts or faulty
workmanship for a period of three years after delivery to the original owner. During this
period, FSR will make any necessary repairs or replace the unit without charge for parts or
labor. Shipping charges to the factory or repair station must be prepaid by the owner,
return-shipping charges (via UPS Ground) will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department
(1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone: (973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site: http://www.fsrinc.com
Table of contents
Other FSR Extender manuals
