FSR RN-WPCS User manual

Caution:
TheRN-WPCShasnouserserviceableparts.
QUICK S TART G UIDE
This Quick Start Guide is intended to help you
begin using the product quickly and easily. For
more detailed instructions, please consult the
User’sManual.
CableConnections
Current product information, downloads, and
technical support are available via the FSR
website that can be found at: www.fsrinc.com
The RN-WPCS
uses a 5-pin captive screw connector.
Boththe connectorontheRN-WPCS and thematingplug
are labeled to identify the signals for each pin. Con-
nect the power supply, SerialCable and IR emitter to
theRN-WPCS.
For connecting to remotely located equipment (i.e., a
projector mounted on the ceiling), use the cable
adapter. Position the cable adapter with the projector
and connect the power supply, IR emitter and Serial
cable to one side of the adapter. Make your long ca-
ble run from the RN-WPCS plug to the adapter. Be sure
to connect each signal toits corresponding signal on
eachsideoftheadapter.
RecommendedMaximumCableLength:50ft
IRLearningTips
The RN-WPCS IR receiver is located on the back of
the unit. While you can aim the IR remote di-
rectly at the receiver, this is not necessary since
 To learn an IR signal, you can have the RN-WPCS
calbox.
 AimtheIRremoteattheupperleftcornerofthe
unit(totheleftoftheDisplayOnbutton).
 If the wallplate is installed in an electrical box, be
sure to aim the remote into the slight gap be-
tweenthePCBandthesideoftheelectricalbox
ForCleanIRcodes:
 centlightsorsunlight
indirectviewoftheIRreceiver
 Holdtheremoteapproximately6-8 inchesfrom
theRN-WPCS
 Press and hold the remote button until you hear
thethree“chirps”indicatingcomplete.
 Use the Help button found on the Learn IR
Commandpanel of theCUfor moredetailedIR
learningtipsandinformation.
CommandTemplates
with the use of FSR provided command
templates for your devices. The FSR tem-
plate libraries will continue to grow and eventu-
ally contain a template for
out if templates are available for your devices,
visitthe FSR website atwww.fsrinc.com. to identify
thedevicesyouplantocontrol. Youmayalsocontact
FSR at [e-mail] for more information.
BEFORE Y OU S TART ...
InstalltheCUSoftware
RN-WPCS
Installthe RN-WPCS
onto your computer
fromtheproductCD.
oo a ga Pro o
FSR Inc.
244 Bergen Boulevard,West Paterson, NJ 07424
Phone: [phone] · Fax: [phone]
Web: www.fsrinc.com · E-mail: [email protected]
LIT1171C

Before starting your real
ommended you gain familiarity with the CU and
RN-WPCS features by trying things. Try anything
youwant,you can’thurtit.
QUICK S TART G UIDE
If not already connected, co nnect the serial cable,
power supply, and IR emitter to the RN-WPCS con-
nector plug. Refer to the “Cable Connections”
reference on the other side of this Quick Start
Guide.
Plug the transformer into facility
AC power. The RN-WPCS Display
quence for approximately 5 sec-
onds before entering normal
startup. Normal startup is indi-
cate normal start and factory baud
rate setting of 9600 bps. The
RN-WPCS then illuminates in its start-
ingmodeasshown totheright.
LaunchtheRN-WPCSCUapplication usingeitherthe
shortcut installed on yourdesktop or the start
cation.
Start on the Fast Setup tab and follow the instruc-
tionsprovidedonthescreensasyougo..
ApplyPowertoyourRN-WPCS
4
StarttheCUSoftwareand
Connect toyourRN-WPCS
5
CreateandSave
6
Before beginning, unpack and inspect your prod-
uct to make sure you have everything and that all
items are free from defects. The product and the
includeditemsareshownbelow:
UnpackandInventory
1
Power
Supply
RN-WPCS
Panel
RN-WPCS
Panel
Serial Cable
Product
CD
IR
Emitters
Cable
Adapter
For anymissingorsuspected defective item,
[e-mail]
CableConnections
2
ConnecttheDB9endoftheserialcabletoyourcomputer.
ConnecttheRN-WPCStoYourComputer
3
Select“DetectRS-232 Connected Devices”,leave
the default comm settings except make sure the
Port is correct for your computer and click the
“Ok” button. The CU will establish communica-
tion with the connected RN-WPCS and the main
application
contact FSR Tech Support to obtain an
RMA number
or call 1-800-332-3771
IR
Emitters

(SERIES WIRING RECOMMENDED)