FTE Maximal SOLTyB kit User manual

SOLTyB
Quick guide
SOLTyB
kit
Quick guide
kit
Quick guide
V1.1

INDEX
CONTENT ....................................................................................................................................................... 1
SAFETY RULES ................................................................................................................................................ 2
INSTALLATION ................................................................................................................................................ 4
ANNEX I: GUIDE TO KNOW THE ANGLE OF THE SOLAR PANELS. ..................................................................... 8

SoltyB Kit
Content
When unpacking the kit boxes check that y
2 x 415 W photovoltaic panels
2 set of 4 mm
2
red and black solar cables with a
section length of 2 meters with MC4 connectors
Power cord
to connect the micro inverter to your
electrical installation. length 5m
4
supports for photovoltaic panels with adjustable
length from 50-85 cm
1
Philips type screw + Nut for the inverter
16 anchor bolts for
floor or wall installation
SOLTyB kit - Quick guide
-1
When unpacking the kit boxes check that y
our kit has the following items:
2 x 415 W photovoltaic panels
1x 800 W micro inverter
red and black solar cables with a
section length of 2 meters with MC4 connectors
Micro Inverter Wi
to connect the micro inverter to your
electrical installation. length 5m
Weatherproof cap
, for inverter cascade
cable connector
supports for photovoltaic panels with adjustable
4 small supports for photovoltaic panels
Philips type screw + Nut for the inverter
4 s
crews and nuts for the
floor or wall installation
16 screws wood installation
Fte maximal – en V1.1
1x 800 W micro inverter
Micro Inverter Wi
-Fi antenna
, for inverter cascade
AC
cable connector
4 small supports for photovoltaic panels
crews and nuts for the
small supports
16 screws wood installation

SOLTyB kit - Quick guide
SoltyB Kit -2 Fte maximal – en V1.1
Safety Rules
1. Before connecting and disconnecting the inverter from the panels, make sure that there is
no voltage at the output of the panels, if necessary, cover the photovoltaic panels.
2. Never connect or disconnect photovoltaic panels with AC voltage connected.
3. Respect the ventilation of the inverter equipment.
4. Do not place the inverter near any heat source or expose it directly to the sun.
5. Avoid getting snow on top of the inverter.
6. Do not subject kit components to temperatures that exceed their operating range.
7. Avoid locations with the possibility of spilling liquids inside the inverter.
8. Never open the panels yourself. In case of problems, always refer to qualified technicians.
9. Never open the inverter by yourself for risk of electrocution. In case of problems, always
refer to qualified technicians.
10. Do not open under any circumstances with the inverter connected to the electrical network.
11. During the connection it is preferable that the inverter is disconnected of the mains.
12. Respect safety regulations during assembly and avoid any situation that puts your security
at risk. Follow the safety regulations at each step of the installation.
13. Observe electrical safety regulations during assembly. Use materials that comply with
current regulations.
14. Never touch the plug with wet hands. Likewise, always disconnect the inverter from the
electrical network before manipulating the connections.
15. Do not put any heavy object on the panels and inverter as it could be damaged.
16. Avoid exposing electrical connectors to sun, rain, and snow.
17. Protect cables from being exposed to sun, rain or snow.
Cleaning of the photovoltaic panels: To maintain the maximum production of the panels, the
PV panel must be clean every 3 or 4 months, unless you live near the sea, which should be
done more frequently. To clean the panels with water using a hose with low pressure to wash
the surface of the panel. Dry it with a glass cleaner. If necessary, you can use a soft, damp
sponge to remove more embedded dirt from the panel. In the event of accumulated snow on
the photovoltaic panels, it must be carefully removed.
Accessories: Do not use accessories that are not specifically approved by the manufacturer.
Unapproved accessories may increase the risk of fire, electric shock, and other damages.
Mains connection: Choose a plug that is easily accessible, so that if you need to unplug it, you
can do it quickly and comfortably. Check that the cable and plug are in good condition. Don’t
pull on the cable, always pull on the plug.
Maintenance and repair: All repairs must be done by authorized personnel. Otherwise, the
warranty is void.

SOLTyB kit - Quick guide
SoltyB Kit -3 Fte maximal – en V1.1
Connection of the inverter and panels and their elements
1) Photovoltaic panel.
2) Cascade AC voltage connector protection cap. You must insert it to protect this connector with
voltage of the mains from the weather.
3) Micro inverter.
4) Wi-Fi antenna. You must remove the red cap to be able to screw the Wi-Fi antenna.
5) Mains cable must be connected to the right side of the inverter and the other end must be
connected to a mains socket when everything is assembled.
6) Photovoltaic panel.
7) Red cable of the first set of 2m cables that connects to the positive input of the male connector
of the solar panel and to the positive input of the female connector of the inverter.
8) Black cable of the first set of 2m cables that connects to the negative input of the solar panel
female connector and to the negative input of the inverter male connector.
9) Black cable of the second set of 2m cables that connects to the negative input of the solar panel
female connector and to the negative input of the inverter male connector.
10) Red cable from the second set of 2m that is connected to the positive input of the male
connector of the solar panel and to the positive input of the female connector of the inverter.

SOLTyB kit - Quick guide
SoltyB Kit -4 Fte maximal – en V1.1
Installation
For the installation of the photovoltaic panels, more than one person is necessary, due to the weight,
dimensions and the care that must be taken with the panels.
Prior steps
Your electrical installation must be verified if you have adequate protections in your electrical panel in
accordance with local regulations. Verify that the socket where the inverter is connected is in a
correct state. Check with a local electrician.
Check that the mains voltage is within the operating range of the included inverter and that the plug
cable corresponds to your type of electrical outlet.
Tools needed for the installation
•13 spanner for the bolt nuts.
•5.5 Allen key used for the screws of the supports
•4 Allen key in the case of using the included wooden floor screws.
•Drill to make the holes in the floor or wall.
•Philips screwdriver
•Protractor to know the inclination of the panels
Installation steps
1. Carefully place the PV panel upside down
on a clean surface.
2. Place the two small brackets in the
panel holes. Use the ones on one of the
long sides of the panel.

SoltyB Kit
3.
Tighten the hinge screws with the
wrenches
5.
Tighten the screw of the long support to
the photovoltaic panel
7.
Adjust the height of the long bracket.
Both long supports should be the
height.
SOLTyB kit - Quick guide
-5
Tighten the hinge screws with the
4.
Tighten the bracket scr
Repeat steps 3 and 4 for the other
small bracket
Tighten the screw of the long support to
the photovoltaic panel
6.
Tighten the screw on the hinge near the
panel
Adjust the height of the long bracket.
Both long supports should be the
same
8.
Tighten the base hinge screw and nut.
Fte maximal – en V1.1
Tighten the bracket scr
ew to the panel.
Repeat steps 3 and 4 for the other
Tighten the screw on the hinge near the
Tighten the base hinge screw and nut.

SoltyB Kit
9.
Mounted long bracket and repeat steps
5-
9 for the other long bracket
11.
Remove the red protector from the Wi
antenna connector and insert the antenna
by turning it into the connector
13.
Connection of the positive cable from the
photovoltaic panel to the inverter. Repeat
for
the other panel using the other input
of the micro-
inverter. Before connecting
the cables, opaque the panels if
necessary to avoid connecting them with
voltage
15. Insert the protective
cap
cascade. Make the
SOLTyB kit - Quick guide
-6
Mounted long bracket and repeat steps
9 for the other long bracket
10.
On one of the two panels, place the
inverter. Use an available hole and
screw and tighten the nut to fix the
inverter to the
panel
Remove the red protector from the Wi
-Fi
antenna connector and insert the antenna
by turning it into the connector
12.
The antenna can be adjusted the angle.
Connection of the positive cable from the
photovoltaic panel to the inverter. Repeat
the other panel using the other input
inverter. Before connecting
the cables, opaque the panels if
necessary to avoid connecting them with
14.
Connection of the negative cable from
the photovoltaic panel to the inverter
Repeat the
connection with the other
photovoltaic panel using the other input
of the micro-
inverter
cap
of the AC cable
cascade. Make the
adequate force to 16.
Cap inserted in the connector.
Fte maximal – en V1.1
On one of the two panels, place the
inverter. Use an available hole and
screw and tighten the nut to fix the
panel
The antenna can be adjusted the angle.
Connection of the negative cable from
the photovoltaic panel to the inverter
connection with the other
photovoltaic panel using the other input
inverter
Cap inserted in the connector.

SoltyB Kit
insert it.
17.
Connect the AC power cord of the
inver
ter. Always connect it with the
schuco plug disconnected
19.
Use zip ties to collect excess cable
21.
Screw the supports to the floor after
adjusting the inclination.
Clean panels if necessary.
Finally connect the plug to the socket of the micro inverter for its start
In the following link you can download the inverter manual and in it you can find the link to the
Solarman application that will allow you to monitor the inverter.
http://www.ftemaximal.com/en/
Note
when following the instructions in the Solarman
WiFi AP is 12345678.
SOLTyB kit - Quick guide
-7
Connect the AC power cord of the
ter. Always connect it with the
schuco plug disconnected
18.
Connecting the AC cable to the inverter
Use zip ties to collect excess cable
20.
Carefully lift the panel up so that it rests
on the brackets and fasten them.
can request help from another
necessary
Screw the supports to the floor after
adjusting the inclination.
22.
Completion of the assembly of the Kit
of the 2 panels
Finally connect the plug to the socket of the micro inverter for its start
-up
In the following link you can download the inverter manual and in it you can find the link to the
Solarman application that will allow you to monitor the inverter.
http://www.ftemaximal.com/en/
when following the instructions in the Solarman
app, the default key of the inverter's built
Fte maximal – en V1.1
Connecting the AC cable to the inverter
Carefully lift the panel up so that it rests
on the brackets and fasten them.
You
can request help from another
person if
Completion of the assembly of the Kit
In the following link you can download the inverter manual and in it you can find the link to the
app, the default key of the inverter's built
-in

SOLTyB kit - Quick guide
SoltyB Kit -8 Fte maximal – en V1.1
NNEX I: Guide to know the angle of the solar panels.
Open your web browser and enter the following address of the PHOTOVOLTAIC GEOGRAPHICAL
INFORMATION SYSTEM calculation tool
https://re.jrc.ec.europa.eu/pvg_tools/en/tools.html
Steps:
1. Select your approximate location with the left mouse click on the map. You can zoom using the +
and – signs at the top left of the map
2. Enter in the box Installed peak PV power [kWp]* the power of your panels in our case 800 W
(0.8 Kw).
3. Check the box optimize slope and azimuth.
4. Press the Visualize results button. In simulation output check the value of the Slope angle to
Know the angle of the PV panel. This angle is from the ground. It also gives you an estimate of the
energy the kit will produce in kWh per month.

BCN DISTRIBUCIONES S.A.U.
Milà i Fontanals 118-120
08205 Sabadell
(Barcelona) Spain
Tel. [phone]
Fax. [phone]
[email protected]
www.ftemaximal.com