Fuel Fitness F85 User manual

1
SAFETY HINTS
IMPORTANT: THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY
SAFETY PRECAUTIONS
Thank you for purchasing our product. Even though we go to great efforts to ensure the quality of each product,
occasional errors and/or omissions do occur. In any event should you find this product to be defective or
missing a part please contact our Customer Service Department.
Your treadmill was designed and built for optimum safety. However, certain precautions apply
whenever you use your treadmill. Be sure to read the manual before assembly and operation.
Also, please note the following safety precautions:
DANGER: To reduce the risk of electric shock, always unplug the treadmill from the electrical outlet
immediately after using and before cleaning.
1. Read OWNER OPERATING MANUAL and all accompanying literature and follow it carefully before using
your treadmill.
2. If dizziness, nausea, chest pains, or any other abnormal symptoms are experienced while using this equipment,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
3. Never leave the treadmill unattended when plugged in. Unplug from the outlet when not in use and before
removing or replacing parts.
4. Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been
dropped, damaged, or exposed to water.
5. Do not pull the treadmill by the power supply cord or use cord as a handle. Keep cord away from heated
surfaces and open flames.
6. Fitness equipment must always be installed and used on a flat surface. Do not use outdoors or near water.
7. Do not insert any objects into any openings.
8. Keep children and pets away from this equipment at all times while exercising.
9. Handicapped individuals should have medical approval and close supervision when using this treadmill.
10.Do not place hands or feet under the treadmill. Always keep hands and legs off of the treadmill when others
are using it.
11.Never turn on treadmill while standing on treadbelt. Always return the treadmill to slow speed to provide for
safe dismount and low speed restart.
a-To disconnect, turn all controls to the off position, then remove plug from outlet.
b-Use the treadmill only for it is intended use as described in this manual.
c-Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This allows your
heart rate to gradually increase and decrease and will help prevent straining muscles.
d-Never hold your breath while exercising. Breathing should remain at a normal rate in conjunction with the
level of exercise being performed.
e-Start your program slowly and very gradually increase your speed and distance.
f-Always wear suitable clothing and footwear while exercising. Do not wear loose fitting clothing
that could become entangled with the moving parts of your treadmill.
g-Do not walk or jog barefoot, in stocking feet or loose fitting shoes or slippers.
h-Care must be taken when lifting or moving the equipment, so as not to injure your back. Always use proper
lifting techniques.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
13. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction
14. Children being supervised not to play with the appliance
WARNING: Before beginning any exercise program consult your physician. This is especially important for
individuals over the age of 35 or persons with pre-existing health problems. Read all instructions before using
any fitness equipment. We assume no responsibility from personal injury or property damage sustained by or
through the use of this product.
CAUTION!! Please be careful when opening this unit.
SZ610A-A923CE_1007A

2
The treadmill has been designed and constructed to provide trouble free usage and enjoyable exercise.
You can greatly improve your understanding and benefits of exercising by carefully reading the instructions
given in this manual. Please familiarize yourself with the maintenance advice provided for you.
Drive Motor: 3.5 hp
Speed Range: 1 – 18 kmph
Running Surface: 510 m/m x 1525 m/m
Incline Level: 0-15 Levels
Folding Design: Manual
INTRODUCTION
MAX.USER WEIGHT 150 KGS
SPECIFICATIONS
Handrail
Running Belt
Main Frame
Wheel
Safet
Console
Handgrip Tube
Speaker
Speed Adjustment Switch
Incline Adjustment Switch
Fan Assembly

3
ASSEMBLY
PACK
CHECK
LIST
#130. 5/16" × 1/2"
Button Head Socket Bolt (8 pcs)
#75.Ellipse Safety Key (1pc) #30.Lubricant (1pc)
#132.M6 Allen Wrench (1pc)
ASSEMBLY PACK CHECK LIST
#131. Combination M5 Allen Wrench
& Phillips Head Screw Driver(1 pc)
#134. M5 × 10 m/m
Phillips Head Screw (8 pcs)
#133. 3/8" × 1-3/4"
Button Head Socket Bolt (4pcs)
#128. M5
Speed Nut Clip (6pcs) #113. ψ10
S
p
li
t
Washe
r
(
4
p
cs
)
#122. 3.5 × 12 m/m
Sheet Metal Screw (4 pcs) #120. 5 × 16 m/m Tapping Screw (6 pcs)
#151. 5/16" × 3/4"
Button Head Socket Bolt (4pcs)

4
ASSEMBLY
■ Step 1.
Remove the treadmill from the carton and lay it aside on a hard, level surface.
■ Step 2.
1. Install the 6pcs of Speed Nut Clip (128) on the Frame Base left and right side.
2. Install the Frame Base Caps (L, R)(61,62) through the Handrails (L, R)(4,5), and connect the
Computer Cable (Lower)(49) and Computer Cable (Middle)(50).
50
49
61
5
4
62
A
SSEMBLY

5
■ Step 3.
Install the Handrails (L, R)(4,5) into the Frame Base (2) with the 8pcs of 5/16”x1/2” Button
Head Socket Bolts (130) by using the Combination M5 Allen Wrench & Phillips Head Screw
Driver (131).
■ Step 4.
Install the Frame Base Caps (L, R)(61,62) on the Frame Base (2) with the 6pcs of 5x16mm
Tapping Screws (120) by using the Combination M5 Allen Wrench & Phillips Head Screw
Driver (131).
■ Step 5.
Connect the Speed Adjustment Switch W/Cable (54) and Speed Cable (Upper)(37).
Connect the Incline Adjustment Switch W/Cable (55) and Incline Cable (Upper)(38).
Connect the Computer Cable (Middle)(50) and Computer Cable (Upper)(48).

6
■ Step 6.
Install the Console Assembly (52) into the Handrails (L, R)(4,5) with the 4pcs of 3/8”x1-3/4”
Button Head Socket Bolts (133) and 4pcs of Ø10 Split Washers (113) by using the M6 Allen
Wrench (132).
■ Step 7.
Install the Left Handgrip Side Caps (L, R)(63,65), Right Handgrip Side Caps (L, R)(66,67) on
the Handrails (L, R)(4,5) and Console Support (6) with the 8pcs of M5x10mm Phillips Head
Screws (134) and 4pcs of 3.5x 12mm Sheet Metal Screws (122) by using the Combination M5
Allen Wrench & Phillips Head Screw Driver (131).

7
■ Step 8.
1. Install the Handrail Support (15) between the Upright Tubes (5,4) with the 4pcs of 5/16”x
3/4” Button Head Socket Bolts (151).
2. Put the Beverage Holder (150) on the Handrail Support (15).
150
NOTE: Please Tighten All Screws After All Components Assembly Complete.

8
UNFOLDING
FOLDING
TRANSPORT
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power
cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired
position.
■Unfoldong The Treadmill:
Apply slight forward pressure* on the treadmill running deck with one hand. Pull down on the
unlocking lever and slowly lower the running deck to the floor. The deck will lower unassisted
when it reaches about waist high. (As shown Figure 1.)
*At the rear roller area to relieve pressure on the locking system.
■Folding The Treadmill:
Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it
is secured by the locking telescoping tube assembly in center back of base.
(As shown Figure 2&3.)
■Transport
The treadmill is equipped with four transport wheels which are engaged when the treadmill is
folded. After folding simply roll the treadmill away. (As shown Figure 4.)

9
ADJUSTMEANT
BELT TRACKING ADJUSTMEANT
If during use you notice that walking belt either shifts to the right or the left of center, first
remove "Safety Key" and unplug equipment from AC power source. Using M6 Allen wrench
provided, turn left rear roller adjustment as indicated below clockwise no more the 1/4" of a turn.
Remove M6 Allen wrench, insert "Safety Key" and insert AC power cord into AC outlet. Turn
on your treadmill and observe after running a few minutes to see if problem has been corrected.
This may take several adjustments, so repeat the above procedure.

10
TREADMILL LUBRICATION
Your treadmill should require little maintenance other then periodically applying lubricant.
Lubricating under the treadbelt will ensure superior performance and extend its life expectancy.
HOW TO CHECK TREADBELT FOR PROPER LUBRICATION?
Lift one side of the treadbelt and feel the top surface of the treadboard.
If the surface is slick to the touch, then no further lubrication is required.
If the surface is dry to the touch, apply one packet of lubricant or half of the bottle of lubricant.
HOW TO APPLY LUBRICANT?
1. Lift one side of treadbelt.
2. Pour one half of the lubricant bottle under the center of the treadbelt on the top surface of the
treadboard.
3. Walk on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant.
NOTE: DO NOT over lubricate treadboard. Any excess lubricant that comes out should be wiped
off.
IMPORTANT: ONLY USE HALF THE BOTTLE OF LUBRICANT PER APPLICATION
LUBRICATION SCHEDULE.
1. If it’s necessary, it’s better to lubricate half a bottle when user open carton to use at first time.
2. We suggest if user doesn’t apply lubricant at first time, after the first 25 hours of use
(2-3 months ) need to apply one half bottle of lubricant.
3. Every 180 hours or 1000km of use apply one half bottle of lubricant per exact situation.

11
FUNCTIONS
COMPUTER OPERATION INSTRUCTIONS
Getting Started:
Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the power switch
located at the front of the treadmill below the motor hood. Ensure that the safety key is installed, as
the treadmill will not power on without it.
When the power is turned on, all the lights on the display will light for a short time. Then the Time and
Distance windows will display Odometer readings for a short time. The Time window will show how
many hours the treadmill has been in use and the Distance window will show how many kilometers (or
miles if the treadmill is set to metric readings; see maintenance for changing settings) the treadmill has
gone. A message will be displayed showing the current software version. The treadmill will then enter
idle mode, which is the starting point for operation.
Quick-Start Operation:
STEP 1: Press and release any key to wake the display up (if not already on).
Note: Installing the tether key will also wake up the console.
STEP 2: Press and release the Start key to begin belt movement at 1.0 km (0.5 mph), then adjust to
the desired speed using the Fast / Slow keys (console or hand rail). You may also use the rapid speed
keys 2 through 12 to set to a specific speed directly.

12
FUNCTIONS
STEP 3: To slow tread-belt press and hold the Slow key (console or hand rail) to the desired speed.
You may also press the rapid speed adjust keys, 2 through 12.
STEP 4: To stop the tread-belt press and release red Stop key.
Treadmill Features:
Pause/Stop/Reset:
STEP 1: When the treadmill is running the pause feature may be utilized by pressing the red Stop
key once. This will slowly decelerate the tread-belt to a stop. The incline will go to zero percent. The
Time, Distance and Calorie readings will hold while the unit is in the pause mode. After 5 minutes
the display will reset and return to the start up screen.
STEP 2: To resume your exercise when in Pause mode, press the Start key. The speed and incline
will return to their previous settings.
Pressing the Stop key twice will end the program and a workout summary will be displayed. If
the Stop button is pressed a third time, the console will return to the idle mode (start up) screen. If the
Stop button is held down for more than 3 seconds the console will reset.
Incline:
Incline may be adjusted anytime after the belt starts moving.
Press and hold the Adjust ▲▼ keys (console or hand rail) to achieve desired level of effort.
You may also choose a more rapid increase / decrease by selecting desired key, 2 through 12, on
left hand side of console (incline).
The display will indicate incline numbers as percent of grade (the same as grade of a road) as
adjustments are made.
Dot Matrix Center Display (Manual Operation):
Ten rows of dots indicate each level of a workout. The dots are only to show an approximate level
(speed/incline) of effort. They do not necessarily indicate a specific value - only an approximate
percent to compare levels of intensity. In Manual Operation the Speed / Incline dot matrix window will
build a profile “picture” as values are changed during a workout. There are twenty-four columns,
which indicate time. The 24 columns are divided into 1/24th of the total time of the program. When the
time is counting up from zero (as in quick start) each column represents 1 minute.
Next to the Dot Matrix window are three LED lights labeled: Track, Speed and Incline, along with a
display button. When the Track LED is lit the dot matrix displays the Track profile, when the Speed
LED is lit the Dot matrix displays the Speed profile and when the Incline LED is lit the Dot Matrix
displays the Incline profile. You may change the Dot Matrix profile view by pressing the Display
button. After scrolling through the three profiles the Dot matrix will automatically scroll through the
three displays showing each one for four seconds. The LED associated with each profile will blink
while that view is displayed. One more press of the Display button will return you to the Track profile.

13
FUNCTIONS
0.4 km (1/4-mile) Track:
The 0.4 km track (1/4-mile) will be displayed around the dot matrix window. The flashing dot indicates
your progress. In the center of the track there is a lap counter for reference.
Pulse Grip Feature:
The Pulse (Heart Rate) window will display your current heart rate in beats per minute during the
workout. You must use both left and right stainless steel sensors on the front cross bar to pick up your
pulse. Pulse values are displayed anytime the computer is receiving a Grip Pulse signal. You may not
use the Grip Pulse feature while in Heart Rate Control. Note: Refer to Important Safety Instructions (page
3) concerning Pulse Grip operation. The grip sensors may not be accurate when you are running on the
treadmill.
Calorie Display:
Displays the cumulative calories burned at any given time during your workout. Note: This is only a
rough guide used for comparison of different exercise sessions, which cannot be used for medical purposes.
Auto-Pilot feature:
This unique feature allows the user to instantly enter the Heart Rate Control mode at any time with the
press of a button.
The HR2 program button also doubles as the Auto-Pilot button.
During any program the user may press the Auto-Pilot button to enter the HRC program. Your current
heart rate (the heart rate you are at when you press Auto-Pilot) will be maintained automatically by the
Auto-Pilot program. You may press the elevation/incline up or down buttons to change your target
heart rate while in the Auto-Pilot mode.
To Turn Treadmill Off:
The display will automatically turn off (blank out) after 30 minutes of inactivity. This function is called
sleep mode. In sleep mode, the treadmill will power down most everything except for a minimum of
circuitry for detecting key presses and the safety key so it will start up again if these are activated.
There is only a tiny amount of current used in sleep mode (about the same as your TV when it is
turned off) and it is perfectly fine to leave the main power switch on in sleep mode.
Of course you may also remove the safety key or turn off the main power switch to power down the
treadmill.
Optional / Speakers:
There is an Audio Input Jack on the front of the console and built-in speakers. You may plug any low-
level audio source signal into this port. Audio sources include MP3, Ipod, portable radio, CD player
or even a TV or computer audio signal. There is an audio patch cable included to and also a
headphone jack for private listening.
Programmable Features
The Series of treadmills offer five preset programs, two user defined programs, two heart rate control
programs and one Manual program.
To Select and start a Program:
STEP 1: Press the desired program fromthe10availableprogramkeys. Then press the enter key to begin
customizing the program with your personal data, or just press the start key to begin the program with
the default settings.

14
FUNCTIONS
STEP 2: After selecting a program and pressing enter to set your personal data, the Time window will
blink with the default value of 20 minutes. You may use any of the up/down keys to adjust the time.
After adjusting the time, press enter. (Note: You may press start at any time during the programming to
begin with only settings you have modified at that point).
STEP 3: The Calorie window will now be blinking a value, indicating your Body Weight. Entering the
correct body weight will affect the calorie count. Use the Up/Down keys to adjust, and then press enter.
* A note about the Calorie display: No exercise machine can give you an exact calorie count because
there are too many factors which determine exact calorie burn for a particular person. Even if someone
is the exact same body weight, age and height, their calorie burn may be very different than yours. The
Calorie display is to be used as a reference only to monitor improvement from workout to workout.
STEP 4: The Heart Rate window will now be blinking a value, indicating your Age.
Entering your correct age affects the heart rate Bar Graph Display and the Heart Rate Control
programs. Use the Up/Down keys to adjust, and then press enter.
Your age determines the maximum heart rate you may achieve. Since the Bar Graph Display and the
Heart Rate control features are based on a percentage of your maximum heart rate, it is important to
enter the correct age for these features to work properly.
STEP 5: The Speed window will now be blinking, showing the preset top speed of the selected
program. Use the Up/Down keys to adjust, and then press enter. Each program has various speed
changes throughout; this allows you to limit the highest speed the program will attain during your
workout.
Now press the Start key to begin your workout.
User Programs:
STEP 1: Select User 1 or User 2 via the PROGRAM keypad then press Enter. Note that the dot matrix
display portion will light a single row of dots at the bottom (Unless there is a previously saved program).
STEP 2: The clock (Time) window will be flashing. Use the up and down adjustment keys to set
the program for the desired time. Press the ENTER key. This is a must to continue even if the time is
not adjusted.
STEP 3: The Calorie window will now be blinking, indicating a bodyweight value. Adjust the number
to your bodyweight value and press enter.
STEP 4: The Pulse window will now be blinking an Age value. Adjust the age and press enter.
STEP 5: The first speed setting column (segment) will now be blinking. Using the Fast / Slow keys,
adjust the speed to your desired effort level for the first segment then press enter. The second column
will now be blinking. Note that the previous segment value has been carried over to the new segment.
Repeat the above process until all segments have been programmed.
STEP 6: The first column will be blinking again. The console is now ready for the incline settings.
Repeat the same process used to set the speed values for programming the segments for incline.
STEP 7: Press the Start button to begin the workout and also save the program to memory.

15
Programmable Operation of Your Treadmill
The old motto, “no pain, no gain”, is a myth that has been overpowered by the benefits of
exercising comfortably. A great deal of this success has been promoted by the use of heart rate
monitors. With the proper use of a heart rate monitor, many people find that their choice of exercise
intensity is either too high or too low and exercise is much more enjoyable by maintaining their
heart rate in the desired benefit range.
To determine the benefit range in
which you wish to train, you must
first determine your Maximum Heart
Rate. This can be accomplished by
using the following formula: 220 -
User’s Age = Maximum Heart Rate.
If you enter your age during
programming of the console the
console will perform this calculation
automatically. This is used for the HR
control programs. After calculating
your Maximum Heart Rate, you can
decide upon which goal you would
like to pursue. The two most popular
reasons for, or goals of exercise, are
cardiovascular fitness (training for the heart and lungs) and weight control. The black columns on the
chart above represent the Maximum Heart Rate for a person whose age is listed at the bottom of each
column. The heart rate training zone for either cardiovascular fitness or weight loss is represented by
two different lines, which cut diagonally through the chart. A definition of the lines’ goal is in the
bottom left-hand corner of the chart. If your goal is cardiovascular fitness or if it is weight loss, it can
be achieved by training at 80% or 60%, respectively, of your Maximum Heart Rate on a schedule
approved by your physician. Consult your physician before participating in any exercise program.
With all Heart Rate Control treadmills you may use the heart rate monitor feature without using the
Heart Rate Control program. This function can be used during manual mode or during any of the
nine different programs. The Heart Rate Control program automatically controls incline.
CAUTION!
The target value used in H-1 and H-2 programs is a suggestion only for normal, healthy individuals.
Do not exceed your limits! You may not be able to obtain your chosen target. If in question, enter a
higher age value that will set a lower target goal.
FUNCTIONS
90

16
Using a Heart Rate Transmitter
How to wear your wireless chest strap transmitter:
1. Attach the transmitter to the elastic strap using the locking parts.
2. Adjust the strap as tightly as possible as long as the strap is not too tight to remain comfortable.
3. Position the transmitter centered in the middle of your body facing away from your chest (some
people must position the transmitter slightly left of center). Attach the final end of the elastic strap by
inserting the round end and, using the locking parts, secure the transmitter and strap around your chest.
4. Position the transmitter immediately below the pectoral muscles.
5. Sweat is the best conductor to measure very minute heart beat electrical signals. However, plain
water can also be used to pre-wet the electrodes (2 black square areas on the reverse side of the belt and
either side of transmitter). It’s also recommended that you wear the transmitter strap a few minutes
before your work out. Some users, because of body chemistry, have a more difficult time in achieving a
strong, steady signal at the beginning. After “warming up”, this problem lessens. As noted, wearing
clothing over the transmitter/strap doesn’t affect performance.
6. Your workout must be within range - distance between transmitter/receiver – to achieve a strong
steady signal. The length of range may vary somewhat but generally stay close enough to the console to
maintain good, strong, reliable readings. Wearing the transmitter immediately against bare skin assures
you of proper operation. If you wish, you may wear the transmitter over a shirt. To do so, moisten the
areas of the shirt that the electrodes will rest upon.
Note: The transmitter is automatically activated when it detects activity from the user’s heart.Additionally, it automatically
deactivates when it does not receive any activity. Although the transmitter is water resistant, moisture can have the effect of
creating false signals, so you should take precautions to completely dry the transmitter after use to prolong battery life
(estimated transmitter battery life is 2500 hours). The replacement battery is Panasonic CR2032.
Erratic Operation:
Caution! Do not use this treadmill for Heart Rate Control unless a steady, solid Actual Heart
Rate value is being displayed. High, wild, random numbers being displayed indicate a problem.
Areas to look at for interference:
(1) Treadmill not properly grounded - A must!
(2) Microwave ovens, TV’s, small appliances, etc.
(3) Fluorescent lights.
(4) Some household security systems.
(5) Perimeter fence for a pet.
(6) Loose bolts on the treadmill console or upright tubes.
(7) The antenna that picks up your heart rate is very sensitive. If there is an outside noise source,
like a radio/cell tower or high tension electric power lines, turning the whole machine 90 degrees may
de-tune the interference.
WARNING!
DO NOT USE THE HEART RATE CONTROL PROGRAM IF YOUR HEART RATE IS NOT
REGISTERING PROPERLY ON THE TREADMILL’S DISPLAY!
F
UNCTIONS

17
Rate of Perceived Exertion
Heart rate is important but listening to your body also has a lot of advantages. There are more
variables involved in how hard you should workout than just heart rate. Your stress level, physical
health, emotional health, temperature, humidity, the time of day, the last time you ate and what you
ate, all contribute to the intensity at which you should workout. If you listen to your body, it will tell
you all of these things.
The rate of perceived exertion (RPE), also know as the Borg scale, was developed by Swedish
physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending upon how you
feel or the perception of your effort.
The scale is as follows:
Rating Perception of Effort
6 Minimal
7 Very,very light
8 Very,very light +
9 Very light
10 Very light +
11 Fairly light
12 Comfortable
13 Somewhat hard
14 Somewhat hard +
15 Hard
16 Hard +
17 Very hard
18 Very hard +
19 Very,very hard
20 Maximal
You can get an approximate heart rate level for each rating by simply adding a zero to each rating.
For example a rating of 12 will result in an approximate heart rate of 120 beats per minute. Your
RPE will vary depending up the factors discussed earlier. That is the major benefit of this type of
training. If your body is strong and rested, you will feel strong and your pace will feel easier.
When your body is in this condition, you are able to train harder and the RPE will support this. If
you are feeling tired and sluggish, it is because your body needs a break. In this condition, your
pace will feel harder. Again, this will show up in your RPE and you will train at the proper level
for that day.
FUNCTIONS

18
Heart Rate Control
Selecting a Heart Rate Control Program:
You have the option, during the setup mode, to choose either the Weight Control (HR-1) program or the
Cardiovascular (HR-2) program. The Weight Control program will maintain your heart rate at 60% of your
Maximum Heart Rate. The Cardiovascular program will maintain your heart rate at 80% of your Maximum
Heart Rate. Your Maximum Heart Rate is based upon a formula that subtracts your age from a constant of 220.
Your HR setting is automatically calculated during the setup mode when you enter your age.
CAUTION!
The target value used in HR-1 and HR-2 programs is a suggestion only for normal, healthy individuals. Do not
exceed your limits! You may not be able to obtain your chosen target. If in question, enter a higher age value
that will set a lower target goal.
Heart Rate Control programming
CAUTION!
Heart rate programs are intended for wireless transmitter chest strap only. Do not use Pulse Grip bar for
Heart Rate Control. You must receive a strong / steady value in heart rate window or the program will not
start.
STEP 1: Press HR1 or HR2 button, and then press Enter.
STEP 2: The Calorie will now be blinking showing bodyweight. Adjust and press enter or press enter
to accept default.
STEP 3: The Pulse window will now be blinking showing age. Adjust and press enter or press enter to
accept default. Adjusting Age will change the Target HR value.
STEP 4: The Time window will now be blinking. Adjust the time and press enter.
STEP 5: Press Start to begin program.
During the program you may increase or decrease the target heart rate by pressing the
elevation/incline up or down buttons.
FUNCTIONS

19
Calibration procedure:
1) Remove the safety key
2) Press and hold down the Start and Fast (speed up) buttons with one hand and replace the safety
key with the other. Continue to hold the Start and Fast key until the window displays “Factory
settings”, then press the enter key.
3) You will now be able to set the display to show Metric or English settings. To do this press the up
or down key to show which you want, then press enter.
4) Make sure the wheel size diameter is 2.810 then press enter
5) Adjust the minimum speed (if needed) to 1.0 km (0.5mile) and then press enter
6) Adjust the maximum speed (if needed) to 18.0 km (12 mile) and then press enter
7) Adjust the maximum elevation (if needed) to 15 and then press enter
8) Press start to begin calibration. The process is automatic; the speed will start up without warning
so do not stand on the belt.
Adjusting the speed sensor:
If the calibration does not pass you may need to check the speed sensor alignment.
1) Remove the motor cover hood by loosening the 4 screws that hold it in place (you do not need to
remove them completely).
2) The speed sensor is located on the left side of the frame, right next to the front roller pulley (the
pulley will have a belt around it that also goes to the motor). The speed sensor is small and black
with a wire connected to it.
3) Make sure the sensor is as close as possible to the pulley without touching it. You will see a
magnet on the face of the pulley; make sure the sensor is aligned with the magnet. There is a
screw that holds the sensor in place that needs to be loosened to adjust the sensor. Re-tighten the
screw when finished.
Maintenance menu:
1) Press and hold the Start, Stop and Enter key at the same time, until the display shows
“Engineering mode” (it may say maintenance menu, depending on version). Press the Enter key.
2) You can now scroll through the menu using the up and down keys. Use the Stop key to return to
previous menu selection. The menu selections are:
1) Calibration (used to verify calibration)
2) Factory settings (These should not be changed unless instructed by Sole service department)
3) Security (This allows you to lock the console keyboard)
4) Functions
i. Sleep (turns sleep mode on or off)
ii. Pause (turns pause mode on or off)
iii. Maintenance (reset lube message and odometer readings)
iv. Units (set display to English or Metric readings)
v. Grade return (returns the elevation to lowest setting when pause is pressed)
5) Display test (lights all LED lights for testing)
6) Key test (tests that all keys are functioning)
FUNCTIONS