Fujikura SH-7 User manual

IINSTRUCTION MANUAL
TUBEHEATER SH-7
Read this instruction manual carefully before operating the equipment.
Keep
this instruction manual carefully.
1. Warning
and Cautions for Safe Operation
Thank you for purchasing Fujikura Tube Heater. This instruction manual also
includes safety requirements.
• Read
this manual carefully before operating the tube heater.
• Keep this
manual carefully.
Fujikura Ltd. accepts no responsibility for personal injury or physical loss including
equipment damage resulting from improper use
or modification.
IAlert Symbol I
This instruction manual indicates'warnings and cautions by using alert symbols. It
is important to undetstand what it means.
WARNING
There is a possibility of personal death or serious injury resulting
from improper use by ignoring this indication.
CAUTION
There is a possibility ofpersonal injury or physical loss resulting
from improper use by ignoring this indication.
IExample of Alert Symbol I
~ Symbol means "PayAttention."
The left symbol indicates "Pay attention to explosion."
(S)Symbol means "Must not
do."
The left symbol indicates "You must not disassemble."
.Symbol means "Must do."
The left symbol indicates
''You must disconnect the AC power cord
from the wall socket or the appliance inlet."

Lf\ WARNING
o
Do not operate the tube heater when it is wet with dew. It can cause
personal injury
or equipment damage.
6)
Do not use the tube heater in circumstance ofextremely hot temperature. It
may cause personal injury or equipment damage.
6)
Do not short-circuit both terminals of the AC adapter. Large electrical
current can cause personalinjury, a fire or equipment damage.
~ CAUTION
0
Do not store the equipment in any area where extreme heat and humidity
are present.
It may cause equipmentdamage.
A\
During I after heating
the splice protector, do not touch the ceramic heater
and the splice protector. The high temperature may cause personalinjury.
0
Do not place the tube heater and AC adapter at an unstable place. In a case
of dropping the equipment,
it can cause personal injury or equipment
damage.
0 Precise adjustment and alignment have been made to this tube heater.
Do
not give a strong shock. Use a carrying case to transport and store the tube
heater. The carrying case will prevent
it from being damaged and provide
protection from moisture, vibration
and
shock during storage and
transportation.
0 Keep
the tube heater free from sand or dust. It degrades the splicing
performance.
0
Do not use any other chemical except alcohol to clean the tube heater. Doing
so may cause blurring, discoloration or deterioration.
0 The tube
heater requires no lubrication. Oil may degrade the performance
and damage it.
0 Repair
or re-adjustment should be performed by an authorized engineer.
Failure to
repair the equipment can result in personal injury or equipment
damage. Please contact a sales agency
in your country.
~ WARNING
0 Never operate the tube
heater in an environment where flammable liquid or
vapor exists.
~
Do not disassemble or modify the tube heater, AC adapter and power cord.
In particular, do not remove or bypass any electrical or mechanical device
(e.g. a fuse or safety switch) incorporated into the design
and manufacturing
of this equipment.
0 This equipment is designed
"for heating splice protector which protects
spliced optical glass fiber for telecommunication.
Do not attempt to heat any
materials other
than the splice protector.
•Safety glass should always be worn during
the fiber preparation. A glass
fiber fragment can be extremely dangerous
if it comes into contact with the
eye, skin, oris ingested.
0 Use only specified power supply unit
and proper AC power source.
• Only
the AC adapter (ADC-08) can be used for supplying power to the
tube heater.
• Proper
AC power source to the ADC-08 is AClOO-240V; 50-60Hz. Check
the AC pow.er source before use. Improper AC power source out of the
range can cause personal injury, emitting smoke
or equipment damage.
• Abnormal high
AC output voltage or freguency from an AC generator is a
common fault. Measure the output
AC voltage with a circuit tester before
connecting
the AC power cord. Improper high voltage or frequency from
generator causes personalinjury, emitting smoke
or equipment damage.
0 Use only specified
AC power cord. Do not put a heavy object on the power
cord. Also,
do not pull, heat up or modify the power cord. Using an improper
cord or a damaged cord can result
in a fire, emitting smoke, equipment
damage
or personal injury.
0 Connect
the AC power cord properly to the appliance inlet and wall socket.
When inserting the
AC plug, confirm no dust or dirt on terminals, and insert
it to the end. Incomplete connection can cause a fire, emitting smoke or
personal injury.
~
Disconnect the AC power cord from the appliance inlet or the wall socket
when
the equipment emits smoke or bad smell, or is noisy or heated up.
Leaving the abnormal condition can cause a fire, personal injury
or
equipment damage.
~
Disconnect the AC power cord from the appliance inlet or the wall socket
when
the equipment is damaged (e.g. by dropping). It may cause personal
injury or equipmentdamage.
~
The appliance inlet is used to disconnect the power cord when the tube
heater is abnormal. Be sure to position the tube heater so that it is easy to
disconnect the power cord.
~
Disconnect the AC power cord from the appliance inlet or the wall socket
when liquid
(e.g. water) or an object (e.g. screw) enters to inside the tube
heater.
It can cause personal injury or equipment damage.
®
Do not touch the tube heater, AC power cord and AC plug with a wet hand.
It can cause personal injury.

scription of Tube Heater
Left Clamp Cover Right Clamp
INn-Ill]
~
m
Fujikura
T.
Heat Time Select Switch
Figure 1 SH-7 View
ModeLED
.-- _._-- ----
-~'rD
TUBE HEATER HEAT MODE SELECT
o c:::J c:::J o
SH-7
SINGtEOO SINGtE40 RIBBON SMALL
HEAT
Mode Select Key
Heat Key
Figure 2 SH-7
Panel View
wer Supply to Tube Heater
(1) PlugAC power cord firmly into the appliance inlet ofAC adapter.
(2) Plug DC power cord of the AC adapter firmly into the appliance connector of
tube heater.
(3) Connect the AC plug firmly into the wall socket.
I!!!!t.. When connecting to an AC generator, measure the output voltage of the
\i.i generator with a circuit tester first.
(4) Selected mode LED lights.
In European Union
Tn accordance with the European Parliament Directive 2002/961EC, electrical parts and
materials that can be re-used andfor recycled have been identified in order that the use of
tr new resources and the amount ofwaste going for landfill can be minimised.
A In the EUropean Union, do not discard this product as unsorted municipal waste. Contact
-
your local authorities.
In other countries
[Recycling]
To recycle this product, disassemble it first, sort each part separately by material components
and follow your local recycling regulations.
[Disposal]
This product can be disposed of same as the standard electric poroducts. Follow your local
2. Components and Options of the tube heater
2.1 Components Quantity Note
The name ofarticle Model name
SH-7
Tube
Heater 1 This
AC Adapter is suit for
ADC-OS
ACAdapter 1 onlySH-7.
1--
This AC Power Cord is suit
-
AC Power Cord 1 fbr only
ADC-OS.
CarrYing Case 1
-English
Instruction Manual 1
3.- Product Specification
1 Applicable Splice
Protector
60mm sleeve for single fiber: FP-03
40mm sleeve for single fiber: FP-03(40mm)
40mm sleeve for
1-8 fibers :FP-04(T)
40mm sleeve for 1-12
fibers: FP-05
20mm sleeve for single fiber: FPSOI-20-250
30mmsleeve for 1-4 fibers: FPS04-30
Ii
.2
r--
3
Splice Protector
ShrinkingTime
Specific for
AC
Adapter
Typ. 105 seconds (FP-04(T) at 25 degree C)
Input voltage: AC 100-240V (50 to 60Hz)
Ou!P.ut voltage: DC12V ( +
10%, -5%)
il
ii
II
Anti-wind
(5) When power is supplied to the tube heater, tube heater checks itself Maximum Permissible Wind
Speed: 15m/s
II
4 Characteristics
automatically.
If anything bad happens, buzzer will continue to beep_ In this
Note: If temperature is lower than 20 degree C, Splice Protector Shrinking time may
case, disconnect
the AC plug from the wall socket, and contact a sales agency. increase. I
II
-5'
Ii
-4-
II

- -
:5] Close the tube heater cover.
[4]
r=[!:: -:~! ... ccdFl} '......
Figure 4 Setting in Tube Heater
:::heck 1: Have the spliced point and splice protector been placed in the center of
the tube heater?
heck
2: Is the fiber not twisted or not bent? Reinforcing the spliced point with the
fiber t",isted
or b_ent state'llla:,>y~b":::re=a:::k::.:t::h::e:..:fi:::b:::e::rs.::.:... ------ ____ --1
:] Press the "HEAT' key. The buzzer indicates upon completion of shrinking.
emoving the splice protector
1] Open the tube heater cover, the left and right tube heater clamps and remove
the splice reinforcement slowly, applying some tension to it.
ote3: At the time
of removal, the end of the splice protector may stick to the
inner surface of the tube heater. Therefore, it is necessary to remove the
reinforcement
with a thin cotton pad.
] Visually check the splice reinforcement for bubbles
and impurities.
at Time
(1) Heating time can be changed as follows
Heat Time Increased
or Decreased heat
Switch time
Position 1 '20 second
than Normal
Position 2 Normal
Position 3 +20 second
than Normal
Position 4 +40 second
than Normal
(2) Use a minus screwdriver to rotate Heat Time Switch.
(3) Select Position 2 for usual use.
TIME
Figure 5
Heat Time Switch
6. Heater Mode
(l)The SH-7 can heat and shrink splice protectors shown below.
~~.
Mode Name Appropriate ProtectorModel Name
SINGLE60
FP'03
.SINGLE40 FP-03(40mm)
RIBBON FP'04(T),FP'05
SMALL FPSOl'20-250,FPS04'30
(2) Green LED on the panel shows selected heater mode.
(3) Before heating, select the appropriate heater mode with the mode switch.
(4) Press the mode switch, and select the heater mode. Refer to the modes shown
below.
SINGLE60 -+ SINGLE40 -+RIBBON -+SMALL -+SINGLE60 -+ ...
7. Reinforcing Spliced Point
(1) Setting the spliced fiber in the tube heater
[I] Move the splice protector to the center of the spliced point and place it in the
tuber heater.
[2] Make sure the spliced point and the splice protector are placed in the center of
the tube heater.
INote 1: Place the t.ensi~n me~b~~ d~~nw~rd. .~ .~-.-
Place in the center
( )
Figure 3 Setting in Tube Heater
[3] Move down the left fiber ribbon to make it touch the heater clamp pin, then the
left clamp automatically closes (See Figure 4 on nextpage).
[4) Next close the right clamp of the tube heater with your hand, slightly pulling
the right fiber.
Note2: The left clamp has spring tension to prevent fiber from bending inside the
splice protector. When pulling the right fiber slightly, confirm sliding
motion
of the left clamp.
-6'

.2 ContactAddross
Inquiries concerning this product should be made to the nearest sales agency or
one of
the following:
Fujikura Europe Ltd:
C51 BarwellBusiness
Park Leatherhead Road,Chessington,
SurreyKT9 2NY England
Tel. +44'20'8240'2000 (Service: +44'20-8240'2020)
Fax. +44-20'8240'2010 (Service: +44'20'8240'2029)
URL http://www.fujikura.co.uk
AFLTelecommunications
2()O Parkway Ellsl;
Dun(:nn, SOU'PH CAROLINA 29334
lI.A,A.
'1\11.
+H,()()-I!:'U')' ,1423
(Service: +1'800'866'3602)
1."lIx,I·1·/oI<l4·433·rm()O
(Service: +1'800'433'5452)
P,O. Box :1127 Spurtllnburg, SC 29304'3127
I lIU, h/;1:1)://www.AFLtele.com
.I.~ujikurll Asill Ltd.
,too AloxlIlldm Road #22'01 PSABuilding Singapore 119963
'1\11. +1lI')-(;'2711312
I."ux. +ClG'(j'2780965
WU, hM:o://www.fuiikura.com.sg
"'ujlklll'lI Ltd,
Opl:ical Fiber & Equipment Department
Inl:omational Sales & Marketing
1+1 Kiba, Koto'ku, 'Thkyo 135'8512 Japan
'1'01. +81'3'5606'1164
Fax. +81'3'0606'1534
URL httE:l/www.fujikura.co.jE/front. e.htm
............................ End ofDocument ._ .............................. -..
KSP75'FP'000834(6
Lh
Edition)
'n
9. Trouble Shoot'
-
n. .:I.
I Trouble Check
Is the AC power cord plugged Plug
the AC power cord in properly.
in?
Power is not
Is the DC power cord of AC
switched on Plug the DC power cord
in properly.
heater?
adapter plugged in the tube
r- ---
Set the protector in proper n(\!Oitinn
Is stllice_protector set properly?
Splice protector
Is the heater mode right? Select a EroEer heater mode.
does not
shrink
Which heat time position is
perfectly Select position
2.
_m
-
10. Guarantee and Contact Address
10.1 Guarantee
1. Guarantee period and limits
In case that the tube heater gets out oforder within one year from the date of
delivery, it will be repaired free of charge. However, warranty repair does not
apply to the following cases regardless ofthe guarantee period:
(1) Trouble or damage due to natural disaster.
(2) Trouble or damage due to abnormal voltage supply.
(3) Trouble or damage due to mishandling.
(4) Trouble or damage due to handling in disregard ofthe operating
procedures
or instructions described in the instruction manual.
(5) Consumables I
2. In case sending the tube heater back
I
II
Please consult the nearest sales agency.
3. Necessary informationfor the repair
Attach papers to the tube heater in order to inform us of details as described
II
j,
below.
II
(1) Your full name, section, division, company, address, phone number and
II
fax number.
II
I
(2) Model name and serial number ofthe tube heater.
II
I,
(3) Encountered Trouble
• What is
the symptom, and when did it happen?
• What is
the present state?
etc.
4. Transportation when sending the tube heater
As the tube heater is a high'precision machine, use the attached carrying case
without fail for transportation, and storage
in order to protect it against
humidity, vibration
and shock. When you request the nearest sales agency to
have the tube heater repair, please send it together with its accessories.
-8'