Fujitsu Siemens Computers Fujitsu Siemens SCENICVIEW P17-2 User manual

Monitor
Operating Manual
English
SCENICVIEW
P17-2 / P19-2 / P20-2

SCENICVIEW P17-2 / P19-2 / P20-2
2
i
Operation of the monitor
The monitor offers the following possibilities that enable it to be optimally adjusted for the respective
user and the respective situation.
Adjusting height, rake and rotation
The monitor height can be adjusted within a range of approx. 2.5 inch/70 mm.
►Grasp the monitor with both hands on the right and left edge of the casing and move it upward
or downward.
The rake of the monitor can be adjusted by -2° (forward) and +35° (back) from its vertical position.
►Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the
desired rake.
The monitor can be rotated by ± 60° from its centre position.
Ê Grasp the monitor with both hands on the right and left edge of the casing and rotate it into the
desired position.

SCENICVIEW P17-2 / P19-2 / P20-2
3
Adjusting portrait format
The monitor can be turned from the "wide format" (landscape mode) into the "high format" position
(portrait mode).
Ê Grasp the monitor with both hands on the right and left edge of the casing, move it into the
highest position and turn it clockwise until it is in the portrait position.
i
You must use corresponding software (pivot software) so that the screen display is also
shown in the portrait mode. This software is included in the delivery (CD-ROM) and must
be installed on your computer.
Ê In the OSD menu you have the option of switching the OSD manually from landscape mode into
portrait mode (see section "Monitor settings using the OSD menu").
To reset the monitor to the landscape mode, the monitor must be turned counter-clockwise. The
OSD display can be reset again in the OSD menu.
Switching the monitor on/off
The main switch at the rear and the ON/OFF switch at the front are used for switching the monitor on
and off.
►Switch the monitor on with the main switch (4) at the rear.
1 = Buttons for the OSD menu
(On-Screen-display)
2 = ON/OFF switch
3 = Power indicator
4 = Main switch
The power indicator (3) lights up blue when the monitor and computer are switched on. The power
indicator lights up orange when the monitor does not receive a video signal or is in the energy saving
mode. The power indicator goes off when the monitor is switched off.

SCENICVIEW P17-2 / P19-2 / P20-2
4
Changing the monitor settings
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs.
Choosing basic monitor settings using the supplied software
If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000,
Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be
set with the CD supplied.
►Insert the supplied CD into the CD-ROM drive.
►Open the Readme file on the CD and follow the instructions in the file.
Your monitor should now already be properly adjusted. If none of the above operating systems is
used or minor corrections are to be made to the screen display, then change the monitor settings
with the OSD menu.
Changing the monitor settings with the buttons of the control panel
213
SELECT / MENU EXIT / AUTO INPUT
1 = Buttons for the OSD menu
(On-Screen-display)
2 = ON/OFF switch
3 = Power indicator
Use the buttons of the control panel to make the following monitor settings directly while the OSD
menu is switched off.
Performing auto-adjustment of the monitor
►Press the AUTO button for approx. 1 second while the OSD menu is switched off.
The Auto Processing message is displayed.
Picture quality and position are set to optimum values for your system.
Selecting input signal (D-SUB/DVI-D)
►Press the INPUT button for calling the Input select setting window.
►Press the
6or 5button to select the desired input (analogue D-SUB or digital DVI-D).
This setting window can also be called, when the OSD menu is locked.
Activating/deactivating muting
►Press the button to switch the sound off and on again.
A message is displayed that the action has been performed.

SCENICVIEW P17-2 / P19-2 / P20-2
5
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor
with the ON/OFF switch.
A message is displayed that the action has been performed.
Please proceed in the same manner to release the locked OSD menu again.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised changes to the monitor
settings.
►Press and hold both buttons 6and 5simultaneously for a few seconds.
A message is displayed that the action has been performed.
Please proceed in the same manner to release the locked ON/OFF switch again.
Monitor settings using the OSD menu
With the buttons on the control panel, call up and use the integrated OSD (On-Screen display) menu.
i
The OSD menu is available in different languages. The English menu names are used in
the following description (default setting). With the OSD function Language in the OSD Setup
you can select another language.
To set the OSD menu, perform the following steps:
►Press the SELECT/MENU button to activate the OSD menu.
The main menu appears on the screen (on the left-hand side) with icons for the setting functions.
The first symbol (Brightness/Contrast) is
highlighted. In the right-hand part of the display
the associated functions are shown.
►If necessary, press the 6or 5button to
mark another icon (e.g. Image adjust).
►Press the SELECT/MENU button to select
the highlighted icon.

SCENICVIEW P17-2 / P19-2 / P20-2
6
The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side).
The first function (H-Position) is highlighted.
►If necessary, press the 6or 5button to
mark another function.
►Press the SELECT/MENU button to select
the highlighted function.
►Press the
6or 5button to adjust the
value for the selected function.
►Press the EXIT/AUTO button to exit the
function.
►If necessary, press the button 6or 5to
mark another function or press the
EXIT/AUTO button to return to the main
menu.
All changes are stored automatically.
If you want to change other settings, select the corresponding function from the OSD main menu. All
possible adjustments of the main menu are described in the following.
i
The OSD menu for analogue monitor operation is described in the following. During digital
operation some functions are not available, as they are not required due to the digital
transmission technology used.
Adjusting the brightness and contrast
Calling the Brightness / Contrast setting window
Brightness Setting the brightness of the display
With this function you change the brightness of the background lighting.
Contrast Setting the contrast of the display
With this function you modify the contrast of bright colour tones.
Black Level Setting the brightness of the display
With this function you modify the contrast of dark colour tones.
Auto Level Setting the brightness of the display
With this function you can automatically set the contrast.
Press the SELECT/MENU button to activate the function.
i
If the contrast is set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.

SCENICVIEW P17-2 / P19-2 / P20-2
7
Adjusting size and position
Calling the Image adjust setting window
H-Position Adjusting the horizontal position
With this function you move the picture to the left or to the right.
V-Position Adjusting the vertical position
With this function you move the picture up or down.
Clock Setting synchronisation
With this function you adjust the picture width to eliminate vertical picture
disturbances.
Phase Eliminating picture interference
With this function you fine-tune your monitor to eliminate picture interference.
Adjusting the volume
Calling the Audio setting window
Volume Setting the volume for playback with the integrated loudspeakers
Mute Switching the loudspeakers off or on
Setting colour temperature and colours
Calling the Colour setting window
Selecting the colour temperature
The "warmth" of the screen colours is set using the colour temperature. The colour
temperature is measured in K (= Kelvin). You can select from sRGB, 6500 K, 7500 K,
9300 K, Native and Custom Colour.
sRGB
Native
Custom Colour
= setting colour display according to the sRGB standard
= Original colour of the LCD display
= User-defined colours
In the user-defined setting you can change the colour ratios of the basic colours
(red, green, blue) as required.

SCENICVIEW P17-2 / P19-2 / P20-2
8
Setting display of the OSD menu
Calling the OSD Setup setting window
Language Setting language for the OSD menu
With this function you choose between English (default setting), French, German,
Italian and Spanish as the language for the OSD menu.
OSD
H-Position
Setting the horizontal position of the OSD menu
With this function you move the OSD menu to the left or to the right.
OSD
V-Position
Setting the vertical position of the OSD menu
With this function you move the OSD menu up or down.
OSD
Timeout
Setting the display duration of the OSD menu
With this function you select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is automatically
faded out.
Setting the display format of the OSD menu
With this function you switch the OSD menu from portrait mode to landscape mode
and vice versa.
OSD
Rotation
Off
On
= The OSD menu is displayed in portrait mode.
= The OSD menu is displayed in landscape mode.
Setting functions in the "Advanced" menu
Calling the Advanced setting window
Input select Selecting input signal
With this function you switch the monitor from the analogue to the digital mode and
vice versa, when two signal sources are connected.
The condition is that the graphic card used supports this function.
Sharpness Adjusting the picture quality in case of interpolation
With this function you set the sharpness of the interpolation filter. Thus the display
can be optimised for pictures or texts.
Resolution
Notifier
Displaying monitor data
The optimum resolution for this monitor is 1280 x 1024 pixels. With the function
activated (On), a message appears on the screen after approx. 30 seconds if a
different resolution is set.
Change the resolution to 1280 x 1024 to achieve optimum picture quality.
With the function deactivated (Off), no message appears.
Factory Recall Activating the factory settings
With this function all settings are reset to the factory settings without prompting for
confirmation.
Press the SELECT/MENU button to activate the function. The Auto Processing
message is displayed.

SCENICVIEW P17-2 / P19-2 / P20-2
9
Displaying information
Calling the Information setting window
With this function the model designation, serial number, resolution, H/V frequency,
input signal and polarity of the synchronisation signal are displayed.
Notes on ergonomic colour adjustment
If you select colours for the display in your application programmes, take note of the information
below.
The primary colours blue and red on a dark background do not produce the minimum required
contrast of 3:1 and are therefore not suitable for continuous text and data entry.
When using several colours for characters and background and giving the primary colours full
modulation, you can obtain very suitable colour combinations (see the following table):
Characters
Background
black white purple blue cyan green yellow red
black + + - + + + -
white + + + - - - +
purple + + - - - - -
blue - + - + - + -
cyan + - - + - - -
green + - - + - - -
yellow + - + + - - +
red - + - - - - +
+ Colour combination very suitable
- Colour combination not suitable because colour locations are too close together, thin characters
are not identifiable or rigorous focusing is demanded of the human eye.

SCENICVIEW P17-2 / P19-2 / P20-2
10
Troubleshooting
Should an error occur, first check the following points. If the distortion is still not eliminated, the
monitor should, if possible, be checked on another computer.
If you are unable to solve the problem, please inform our help desk.
Having this problem? Check the following points:
No screen display
(power indicator does not light)
►Check whether the main switch at the rear of the
monitor is switched on.
►Check whether the power cable on the monitor is
connected correctly.
►Check whether the computer is switched on.
No screen display
(power indicator lights)
►Check whether the computer is switched on.
►Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
►Press any key on the computer keyboard - the
computer may be in energy saving mode.
►Alter the brightness and/or contrast until you get a
picture.
Message:
No Signal
►Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
►Check whether the computer is switched on.
Message:
Frequency out of range:
## kHz / ## Hz
Please change the display mode
to 1280 x 1024 with 60 Hz.
Please change the display mode
to 1600 x 1200 with 60 Hz.
The input signal (horizontal frequency and refresh rate)
at the displayed input does not correspond to the
technical monitor data.
►Adjust the video frequency range using the
computer software (see documentation for your
computer or your graphics card).
►Adjust a different screen resolution using the
computer software (see documentation for your
computer or your screen controller).
P17-2/P19-2 P20-2
1280 x 1024 1600 x 1200
Picture position not correct The monitor recognises an undefined mode (see the
"Technical data" chapter).
►Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.
Picture is shaking ►Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
►Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.