Fujitsu Siemens Computers SCENICVIEW B17-5 User manual

Professional Monitor English
Operating Manual
SCENICVIEW B17-5/B19-5

Are there ...
... any technical problems or other questions that you would like help with?
Please contact:
• our Hotline/Help Desk (refer to the enclosed Help Desk List or go to:
"www.fujitsu-siemens.com/support/")
• your sales partner
• your sales office
The latest information on our products, tips, updates etc. can be found on
our website at: "www.fujitsu-siemens.com"

This manual was produced byXerox Global Services
Published by
Fujitsu Siemens Computers GmbH
AG04/08
Edition1
Order no.: A26361-K1255-Z120-1-7619

SCENICVIEW B17-5/B19-5
Your LCD screen... 1
Important notes 3
Getting started 7
Operation 14
Troubleshooting 22
Notes regarding the DIN EN ISO
13406-2 standard 24
Technical data 25
Operating Manual

VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association.
Copyright © Fujitsu Siemens Computers GmbH2008
All rights reserved, including in particular rights of translation, reproduction by printing,
copying or similar methods, in part or in whole.
Non-compliance is subject to compensation for damages.
All rights reserved, including rights created by patent grant or registration of a utility model or design.
Subject to availability and technical modifications.
No liability for content or printing errors.

Contents
Contents
YourLCDscreen... ..................................................................... 1
Targetgroup ............................................................................ 1
Furtherinformation ...................................................................... 2
Notational conventions .................................................................. 2
Importantnotes ........................................................................ 3
Safetyinstructions ...................................................................... 3
Powercable ............................................................................ 4
Transporting the device .................................................................. 4
Cleaningthedevice ..................................................................... 4
CEmarking ............................................................................ 5
EnergyStar ............................................................................ 5
Disposal and recycling .................................................................. 6
Getting started ......................................................................... 7
Unpacking and checking the delivery . . ................................................... 7
Settingupthedevice .................................................................... 7
Setting up an ergonomic video workstation ............................................ 8
Adjustingtheheight ................................................................. 9
Adjustingtheinclination .............................................................. 9
Adjustingtherotation ................................................................ 9
Adjustingportraitformat ............................................................. 10
Removingmonitorbase .............................................................. 10
Connecting the device . .................................................................. 11
Connecting cables to the monitor . . ................................................... 12
Connecting cables to the computer ................................................... 13
Operation .............................................................................. 14
Switching thedeviceonandoff .......................................................... 14
Notes on powermanagement ............................................................ 15
Changing themonitorsettings ............................................................ 15
Changing the monitor settings with the buttons of the control panel . ..................... 16
Changing themonitorsettingsusingtheOSD menu .................................... 17
Troubleshooting ....................................................................... 22
Notes regarding the DIN EN ISO 13406-2 standard . . .................................... 24
Technicaldata ......................................................................... 25
VESA-DDC-compatible VGA interface . ................................................... 26
Preset operating modes . . . . . . ........................................................... 26
Most frequent operating modes ....................................................... 27
SUBDport ............................................................................. 27
DVI-Dport .............................................................................. 28
A26361-K1255-Z120-1-7619, edition 1

Contents
A26361-K1255-Z120-1-7619, edition 1

Your LCD screen...
Your LCD screen...
has a whole range of useful features and functions, e.g.:
• TFT display (Thin Film Transistor; active matrix)
• minimal space requirements thanks to slim casing
• optimum ergonomic characteristics (totally distortion-free, excellent picture
definition and colour purity right into the corners)
• high degree of brightness and good contrast
• high resolution (1280 x 1024)
• presentation of up to 16.7 million colours (in conjunction with an appropriate display adapter)
• automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates
(vertical frequencies) from 56 to 75 Hz (absolutely flicker-free)
• digital screen controller with microprocessor for storing 28 different display modes
• freely adjustable colour alignment for matching the screen colours to the
colours of various input and output devices
• convenient operation via integrated OSD (On-Screen-display) menu
• VESA-DDC compatibility
• VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) –
Mounting device for swivel arm and wall bracket
• Plug&Play capability
• power management for reducing power consumption when the computer is not in use
• Compliance with the recommendations according to TCO ’03
• the monitor fulfills all GS ("Geprüfte Sicherheit", Certified Security) requirements.
This operating manual contains important information you require to start up and run your LCD monitor.
A graphics card (display adapter) with VGA interface or a digital display adapter with
DVI interface is required to control the LCD monitor. The monitor processes the data
supplied to it by the display adapter. The display adapter or the associated driver software
is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be
optimally adapted to the display adapter used and adjusted in accordance with your
needs (see chapter "Changing the monitor settings", Page 15.
Target group
You don’t need to be an "expert" to perform the operations described here. However, please observe
the safety information given in the operating instructions for the computer and in this manual.
In the event of any problems occurring, please contact your sales outlet or our Help Desk.
A26361-K1255-Z120-1-7619, edition 1 1

Your LCD screen...
Further information
Details of how you set the resolution and refresh rate are provided in the documentation
for your display adapter and the associated driver software.
For ergonomic reasons, a screen resolution of 1280 x 1024 pixels is recommended.
Because of the technology used (active matrix) an LCD monitor provides a totally
flicker-free picture even with a refresh rate of 60 Hz.
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
this warning will endanger your life, will damage the device or lead to loss
of data. The warranty will be invalidated if you cause defects in the device
through failure to take notice of this warning
indicates important information that is required to use the device properly.
►indicates an activity that must be performed in the order shown
indicates a result
This style flags data entered using the keyboard in a program dialog or command
line, e.g. your password (Name123) or a command to launch a program
(start.exe)
This style refers to information displayed by a program on the screen, e.g.:
Installation is completed
This style is for
• terms and texts in a software user interface, e.g.: Click Save.
• names of programs or files, e.g. Windows or setup.exe.
"This style" is for
• cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For more
information, go to "www.fujitsu-siemens.com"
• indicates names of CDs and DVDs as well as names and titles of other
materials, e.g.: "CD/DVD Drivers & Utilities" or "Safety" manual
Abc refers to a key on the keyboard, e.g.: F10
This style flags concepts and text that are emphasised or highlighted, e.g.: Do not
switch off device
2 A26361-K1255-Z120-1-7619, edition 1

Important notes
Important notes
ImportantnotesNotes
In this chapter you will find information regarding safety which it is essential to
take note of when working with your device.
Safety instructions
This device complies with the relevant safety regulations for data processing equipment,
including electronic office machines for use in an office environment. If you have any
questions, contact your sales outlet or our Help Desk.
• The display surface of the device is sensitive to pressure and scratches. You should therefore
be careful with the display surface in order to avoid lasting damage (scratches).
• If the device is brought into the installation site from a cold environment, condensation
can form. Before operating the device, wait until it is absolutely dry and has reached
approximately the same temperature as the installation site.
• When installing and operating the device, please observe the notes on environmental
conditions in Chapter "Technical data", Page 25 as well as the instructions in Chapter
"Setting up an ergonomic video workstation", Page 8.
• To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear.
• The device automatically sets itself to the correct voltage within the range from 100 V to 240 V.
Make sure that the local mains voltage is neither higher nor lower than this range.
• Ensure that the power socket on the device and the mains outlet are freely accessible.
• The ON/OFF switch does not disconnect the monitor from the mains voltage. To disconnect
fully from the mains supply, disconnect the power plug from the socket.
• The device is equipped with a power cable that complies with safety standards.
• Use the supplied power cable only.
• Lay the cables in such a way that they do not create a hazard (danger of tripping)
and cannot be damaged. When connecting the device, observe the relevant
notes in chapter "Connecting the device", Page 11.
• No data transfer cables should be connected or disconnected during a thunderstorm.
• Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get
inside the device (danger of electric shock, short circuit).
• The device is not waterproof! Never immerse the device in water and protect
it from spray water (rain, sea water).
• In emergencies (e.g. damaged casing, elements or cables, penetration of
liquids or foreign matter), switch off the device, disconnect the power plug and
contact your sales outlet or our Help Desk.
• Repairs to the device must only be performed by qualified technicians. Unauthorised opening
and incorrect repair may greatly endanger the user (electric shock, fire risk).
• Only use the screen resolution settings and refresh rates specified in Chapter
"Technical data", Page 25. Otherwise you may damage the device. If you are in
any doubt, contact your sales outlet or our Help Desk.
• Use a screen saver with moving images and activate the power management for
your monitor to prevent still images from "burning in".
• If you operate the device with the swivel arm or wall bracket, it must not be turned by 180°.
A26361-K1255-Z120-1-7619, edition 1 3

Important notes
• The device must only be operated in landscape mode (0°) and portrait mode (90°). The
control buttons are located in the middle of the bottom of the monitor in landscape mode
(0°) and at the left-hand side of the monitor in portrait mode (90°).
• Store this manual close to the device. If you pass the device on to third
parties, you should pass this manual on with it.
• We recommend that you place your device on a durable, non-slip surface. In view
of the many different finishes and varnishes used on furniture, it is possible that the
feet of the device may mark the surface they stand on.
• To ensure sufficient ventilation, the air supply and air outlet openings of
the monitor must never be blocked.
Power cable
Use the supplied power cable only.
Use the following guidelines if it is necessary to replace the original cable set.
• The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
• The cable has to be HAR-certified or VDE-certified. The mark HAR or
VDE will appear on the outer sheath.
• For devices which are mounted on a desk or table, type SVT or SJT cable sets may be
used. For devices which sit on the floor, only SJT type cable sets may be used.
• The cable set must be selected according to the rated current for your device.
• If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transporting the device
Device,Trans porta tionRetransportation
Transport all parts separately in their original packaging or in a packaging which
protects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
Cleaning the device
Switch off the device and unplug the power plug.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid enters the device.
The display surface of the device is sensitive to pressure and scratches. Clean
it only using a soft, slightly moistened cloth.
The surface of the casing can be cleaned with a dry cloth. If particularly dirty, use a cloth that
has been moistened in mild domestic detergent and then carefully wrung out.
4 A26361-K1255-Z120-1-7619, edition 1

Important notes
CE marking
The shipped version of this device complies with the requirements of EEC
directives 2004/108/EC "Electromagnetic compatibility" and 2006/95/EC
"Low voltage directive".
Energy Star
EnergyStar
The Fujitsu Siemens LCD colour monitor is equipped with
a power management system which reduces the power
draw in OFF mode to less than 1 W. With this new power
management the LCD monitor satisfies the requirements for
the U.S. Environmental Protection Agency’s (EPA) Energy Star
Computers award.
The EPA estimates that computer equipment uses 5 % percent of all business electricity
and that this is growing rapidly. If all desktop PCs and peripherals enter a low-power mode
when not in use, the overall savings in electricity could amount to $2 billion annually.
These savings could also prevent the emission of 20 million tons of carbon dioxide into
the atmosphere - the equivalent of 5 million automobiles.
As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this
product meets the Energy Star guidelines for energy efficiency.
A26361-K1255-Z120-1-7619, edition 1 5

Important notes
Disposal and recycling
This device has been manufactured to the highest possible degree from materials which
can be recycled or disposed of in a manner that is not environmentally damaging. The
device may be taken back after use to be recycled, provided that it is returned in a
condition that is the result of normal use. Any components which cannot be recycled
will be disposed of in an environmentally acceptable manner.
The device must be disposed of in accordance with the local regulations for disposal of
special waste. The screen background lighting contains mercury. You must observe the
applicable handling and disposal safety regulations for fluorescent tubes.
If you have any questions on disposal, please contact your local office, our Help Desk, or:
Germany Belgium Switzerland
Fujitsu Siemens
Computers GmbH
Remarketing and Recycling
D-33106 Paderborn
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15
"http://www.fujitsu-siemens.de
/wvm"
RECUPEL Boulevard
Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: [phone]
E-mail: [email protected]e
"http://www.recupel.be"
SWICO Swiss Association for
Information, Communications
and Organization Technology
For a list of SWICO
collection points, see:
"http://www.swico.ch".
Asia USA
Taiwan: Environmental
Protection
Administration
Executive Yuan R.O.C.
"http://recycle.epa.gov.tw"
Fujitsu Siemens Computers Inc.
1250E. Arques
Avenue Sunnyvale,
CA 94085 U.S.A.
Contact: Schroettle-Henning,
Bernd
Phone No.: [phone]
Fax No.: [phone]
For more information on this subject, please go to "www.fujitsu-siemens.com/recycling".
6 A26361-K1255-Z120-1-7619, edition 1

Getting started
Getting started
Unpacking and checking the delivery
The display surface of the device is sensitive to pressure and scratches.
Always hold the device by the casing!
The complete device package includes:
• one monitor
• one data cable (D-SUB)
• one data cable (DVI-D)
• one audio cable
• one power cable
• one CD with software and documentation
• one Warranty Booklet
• one "Safety" manual
►Unpack all the individual parts.
►Check the contents of the package for any visible damage caused during transport.
►Check whether the delivery conforms to the details in the delivery note.
►Should you discover that the delivery does not correspond to the delivery
note, notify your local sales outlet immediately.
Do not discard the original packing material of the devices. You may need the
packaging in the future if you need to transport your device.
Settingupthedevice
To ensure sufficient ventilation, the air inlet and outlet openings of
the device must be kept clear.
A26361-K1255-Z120-1-7619, edition 1 7

Getting started
Setting up an ergonomic video workstation
1
►Do not position the video workstation
opposite a window (1).
1
►Position the monitor outside the reach
of a light source (1).
1
►Position the keyboard where it is
easiest to reach (1).
8 A26361-K1255-Z120-1-7619, edition 1

Getting started
1
50 cm
►Position the monitor so that the eye distance
to the screen (1) is around 50 cm.
30
30
65
65
0
60
1
22
►Position the monitor for optimum viewing
(1). The monitor should under no
circumstances fall outside the permissible
viewing space (2).
Depending on the situation, it may be advisable to use a swivel arm or wall
bracket (VESA FPMPMI), which are available from specialist dealers. For
this purpose the monitor base must be removed beforehand as described
in Chapter "Removing monitor base", Page 10.
Adjusting the height
The height of the monitor can be adjusted by approximately 120 mm.
►Grasp the monitor with both hands on the right and left edge of the casing
and move it upward or downward.
Adjusting the inclination
►Hold the monitor with both hands on the left and right sides of the casing
and move it to the desired angle.
Adjusting the rotation
The monitor can be horizontally rotated by ± 45° from its centre position.
►Grasp the monitor with both hands on the right and left edge of the casing
and turn it to the desired position.
A26361-K1255-Z120-1-7619, edition 1 9

Getting started
Adjusting portrait format
The monitor can be rotated from horizontal format (landscape mode) into
vertical format (portrait mode).
►Grasp the monitor with both hands on the right and left edge of the casing, move it into
the highest position and turn it clockwise until it is in the portrait position.
For you to be able to display the screen contents in portrait mode, your graphics card
will also need to support this function or you will need to use special software.
In the OSD menu you have the option of switching the OSD manually
from landscape mode to portrait mode (see "Changing the monitor
settings using the OSD menu", Page 17).
To reset the monitor to landscape mode, the monitor should be turned anti-clockwise.
The OSD display can be reset again in the OSD menu.
Removing monitor base
Before you can use a swivel arm or a wall bracket, you must remove the monitor base.
The display surface is susceptible to scratching!
►Switch off the monitor and pull the power
plug out of the power socket.
►Lay the monitor on its face on a soft surface.
►Remove all cables.
►To remove the monitor base, undo the
screws on the monitor base.
You can now mount a swivel arm or a wall
bracket in accordance with VESA FPMPMI
using a hole spacing of 100 mm.
For instructions on how to mount the
swivel arm or wall bracket, please
see the documentation for the swivel
arm or wall bracket.
Please observe the safety information in "Important notes", Page 3.
For instructions on how to mount the swivel arm or wall bracket, please see
the documentation for the swivel arm or wall bracket.
10 A26361-K1255-Z120-1-7619, edition 1

Getting started
Connecting the device
Please observe the safety information in "Important notes", Page 3.
CE conformance and optimum picture quality are guaranteed only if
you use the data cables supplied.
►Switch off the monitor and the computer.
►Disconnect the power plug from the computer.
A26361-K1255-Z120-1-7619, edition 1 11

Getting started
Connecting cables to the monitor
The monitor ports are protected by a cover.
The supplied data cables have two 15-pin D-SUB connectors or two 24-pin DVI
connectors for connection to the monitor and to the computer.
Information on the computer connections and interfaces is contained in the
operating manual for the computer.
►Remove the cover (2).
►Select the appropriate data cable for your computer.
14 5 3
2
1 = Mains socket
2 = Security slot for the "Kensington Lock"
3 = D-SUB socket (ANALOG)
4 = AUDIO-IN socket
5 = DVI-D connector (DIGITAL)
►Connect one of the connectors of the data cable to the D-SUB connector (3) or the DVI-D
connector (4) on the monitor and secure the plug-in connection by tightening the retaining screws.
►Insert one connector of the audio cable in the AUDIO IN (5) socket on the
monitor and make sure it is properly engaged.
►Connect the supplied mains cable into the power socket (1) of the monitor.
A lock (Kensington Lock) can be mounted in the security slot to protect the monitor
against theft. A Kensington lock is not supplied with the monitor.
12 A26361-K1255-Z120-1-7619, edition 1