Fujitsu Siemens Computers SCENICVIEW P17-1A User manual

Betriebsanleitung / Operating Manual
Monitor SCENICVIEW P17-1A
Deutsch - English
answers
2

Sie haben ...
... technische Fragen oder Probleme?
Wenden Sie sich bitte an
unseren Help Desk (siehe Garantieheft).
Aktuelle Informationen zu unseren Produkten, Tipps, Updates usw. finden Sie im Internet:
http://www.fujitsu-siemens.com
Are there ...
... any technical problems or other
questions you need clarified?
Please contact
our Help Desk (see Warranty Booklet).
The latest information on our products, tips, updates, etc., can be found on the Internet under:
http://www.fujitsu-siemens.com

Dieses Handbuch wurde auf Recycling-Papier gedruckt.
This manual has been printed on recycled paper.
Ce manuel est imprimé sur du papier recyclé.
Este manual ha sido impreso sobre papel reciclado.
Questo manuale è stato stampato su carta da riciclaggio.
Denna handbok är tryckt på recyclingpapper.
Dit handboek werd op recycling-papier gedrukt.
Herausgegeben von/Published by
Fujitsu Siemens Computers GmbH
Bestell-Nr./Order No.: A26361-K960-Z101-1-5E19
Printed in Taiwan
AG 0504 05/04
A26361-K960-Z101-1-5E19

SCENICVIEW P17-1A
LCD-Bildschirm
LCD monitor
Betriebsanleitung
Operating Manual
Deutsch
English
TCO'99
Ausgabe Mai 2004
May 2004 edition

VESA, DDC und DPMS sind eingetragene Warenzeichen der Video Electronics Standards
Association.
Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des
Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren.
Zuwiderhandlungen verpflichten zu Schadenersatz.
Alle Rechte vorbehalten, insbesondere für den Fall der Patenterteilung oder GM-Eintragung.
Liefermöglichkeiten und technische Änderungen vorbehalten.
Dieses Handbuch wurde erstellt von
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright Fujitsu Siemens Computers GmbH 2004
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards
Association.
All rights, including rights of translation, reproduction by printing, copying or similar methods,
even of parts are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved.
Delivery subject to availability. Right of technical modification reserved.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de

A26361-K960-Z101-1-5E19 English
Contents
Introduction........................................................................................................................................1
Notational conventions...............................................................................................................2
Important notes .................................................................................................................................2
Safety notes...............................................................................................................................2
Cleaning ....................................................................................................................................3
Transport ...................................................................................................................................4
Power cable...............................................................................................................................4
Energy Star Guidelines..............................................................................................................4
CE marking................................................................................................................................4
FCC Class B Compliance Statement.........................................................................................4
Declaration of Conformity ..........................................................................................................5
Disposal and recycling...............................................................................................................6
Checking the contents of the consignment ........................................................................................6
Installing an ergonomic video workstation..........................................................................................7
Mounting and removing the monitor base ..........................................................................................8
Mounting/removing lower section of monitor base .....................................................................8
Removing entire monitor base ...................................................................................................8
Connecting the monitor....................................................................................................................10
Connecting cables to the monitor.............................................................................................10
Connecting cables to the computer..........................................................................................11
Operation of the monitor..................................................................................................................12
Adjusting height, rake and rotation...........................................................................................12
Adjusting portrait format...........................................................................................................12
Switching the monitor on/off.....................................................................................................13
Notes on power management..................................................................................................13
Changing the monitor settings .................................................................................................14
Notes on ergonomic colour adjustment............................................................................................20
Technical data .................................................................................................................................20
VESA-DDC-compatible VGA interface.....................................................................................21
Preset operating modes...........................................................................................................22
Pin assignment D-SUB ............................................................................................................22
Troubleshooting...............................................................................................................................23

A26361-K960-Z101-1-5E19 English - 1
Introduction
Your new LCD (Liquid Crystal Display) monitor SCENICVIEW P17-1A offers numerous features and
functions, for example:
●TFT display (Thin Film Transistor; active matrix)
●minimal space requirements thanks to slim casing
●optimum ergonomic characteristics (totally distortion-free, excellent picture definition and
colour purity right into the corners)
●high degree of brightness and good contrast
●high resolution (1280x1024) for displaying the information content of a conventional 19-inch
screen with CRT (Cathode Ray Tube)
●presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)
●automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical
frequencies) from 55 to 75 Hz (absolutely flicker-free)
●digital screen controller with microprocessor for storing 33 different display modes
●freely adjustable colour alignment for matching the screen colours to the colours of various
input and output devices
●convenient operation via integrated OSD (On-Screen-display) menu
●VESA-DDC compatibility
●VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) - mechanical
interface to swivel arm and wall bracket)
●plug&play capability
●power management for reducing power consumption when the computer is not in use
●compliance with the recommendations in accordance with TCO’03
In normal screen mode (dark characters against a light background) the monitor satisfies the
ergonomic requirements for the GS symbol.
This operating manual contains important information you require to start up and run your LCD
monitor.
A screen controller with VGA interface is required to control the SCENICVIEW P17-1A LCD monitor.
The monitor processes the data supplied to it by the screen controller. The screen controller/the
associated driver software is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs (see the
"Changing the monitor settings" section in the "Operation of the monitor" chapter).
Target group
You don't need to be an "expert" to perform the operations described here. Do, however, read the
"Important notes" chapter in the operating manual of the computer and in this operating manual.
In the event of any problems occurring, please contact your sales outlet or our help desk.
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your
screen controller/the associated driver software.

Colour Monitor SCENICVIEW P17-1A
2 - English A26361-K960-Z101-1-5E19
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
!
Pay particular attention to text marked with this symbol. Failure to observe this warning
endangers your life, destroys the device, or may lead to loss of data.
i
Supplementary information, remarks, and tips follow this symbol.
►Text which follows this symbol describes activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters or terms.
Texts in italics indicate filenames and menu items.
Important notes
!
In this chapter you will find information regarding safety which is essential to take note of
with your monitor.
Safety notes
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our help desk.
●The display surface of the LCD monitor is sensitive to pressure and scratches. You should
therefore be careful with the display surface so as to avoid lasting damage (Newton rings,
scratches).
●If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
●During installation and before operating the device, please observe the instructions on
environmental conditions in the "Technical data" chapter as well as the instructions in the
"Installing an ergonomic video workstation" chapter.
●To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never
be blocked.
●The device automatically sets itself to the correct voltage within the range from 100 V to 240 V.
Ensure that the local mains voltage lies within these limits.
●Ensure that the power socket on the device or the grounded mains outlet is freely accessible.
●The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.

Colour Monitor SCENICVIEW P17-1A
A26361-K960-Z101-1-5E19 English - 3
●Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "Connecting the monitor" chapter.
●If you use a different data cable from the one supplied, ensure that it is adequately shielded.
CE conformance and optimum picture quality are guaranteed only if you use the data cable
supplied.
●No data transfer cables should be connected or disconnected during a thunderstorm.
●Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the
device (danger of electric shock, short circuit).
●In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help
desk.
●The screen background lighting contains mercury. You must observe the applicable handling
and disposal safety regulations for fluorescent tubes.
●Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).
●You may set only those resolutions and refresh rates specified in the "Technical data" chapter.
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our help desk.
●Use a screen saver with moving images and activate the power management for your monitor
to prevent still images from "burning in".
●Keep this operating manual together with your device. If you pass on the device to third
parties, you should include this manual.
Cleaning
●Always pull out the power plug before you clean the monitor.
●Do not clean any interior parts yourself, leave this job to a service technician.
●Do not use any cleaning agents that contain abrasives or may corrode plastic.
●Ensure that no liquid will run into the system.
●Ensure that the ventilation areas of the monitor are free.
●The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.

Colour Monitor SCENICVIEW P17-1A
4 - English A26361-K960-Z101-1-5E19
Transport
●Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.
●Never drop the LCD monitor (danger of glass breakage).
Power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary
to replace the original cable set.
●The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
●The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
●For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
For devices which sit on the floor, only SJT type cable sets may be used.
●The cable set must be selected according to the rated current for your device.
Energy Star Guidelines
The Fujitsu Siemens LCD colour monitor SCENICVIEW P17-1A is
designed to conserve electricity by dropping to less than 3 W when it goes
into standby, suspend and OFF mode. With this new power management
the SCENICVIEW P17-1A qualifies for the U.S. Environmental Protection
Agency's (EPA) Energy Star Computers award.
The EPA estimates that computer equipment uses 5 % percent of all business electricity and that
this is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in
use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings
could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the
equivalent of 5 million automobiles.
As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product
meets the Energy Star guidelines for energy efficiency.
CE marking
The shipped version of this device complies with the requirements of the EEC
directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage
directive".
FCC Class B Compliance Statement
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-
Causing Equipment Regulations. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate

Colour Monitor SCENICVIEW P17-1A
A26361-K960-Z101-1-5E19 English - 5
radio frequency energy and, if not installed and used in strict accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between equipment and the receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused
by unauthorised modifications of this equipment or the substitution or attachment of connecting
cables and equipment other than those specified by Fujitsu Siemens Computers GmbH. The
correction of interference caused by such unauthorised modification, substitution or attachment will
be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC rules.
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Product name: Colour LCD Monitor
Trade name: Fujitsu Siemens Computers Inc.
Model number(s): SCENICVIEW P17-1A
Name of responsible party: Fujitsu Siemens Computers, Inc.
598 Gibraltar Drive
Milpitas, CA 95035 - 6315
U.S.A.
Contact person: Bernd Schroettle-Henning
Phone No.: [phone]
Fax No.: [phone]
We, Fujitsu Siemens Computers, Inc., hereby declare that the equipment bearing the trade name
and model number specified above was tested conforming to the applicable FCC rules under the
most accurate measurement standards possible, and that all the necessary steps have been taken
and are in force to assure that production units of the same equipment will continue to comply with
the Commissions requirements.

Colour Monitor SCENICVIEW P17-1A
6 - English A26361-K960-Z101-1-5E19
Disposal and recycling
This device has been manufactured to the highest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging. The device may be taken
back after use to be recycled, provided that it is returned in a condition that is the result of normal
use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
If you have any questions on disposal, please contact your local office, our help desk, or:
Germany Belgium Switzerland
Fujitsu Siemens Computers
GmbH
Remarketing und Recycling
D-33106 Paderborn
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15
http://www.fujitsu-siemens.de/wvm
RECUPEL
Boulevard Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: +32 2 / 706 86 13
E-Mail: [e-mail]
http://www.recupel.be
SWICO
Schweizerischer
Wirtschaftsverband der
Informations-,
Kommunikations- und
Organisationstechnik
A list of the SWICO
Acceptance places can be
found at:
http://www.swico.ch
Checking the contents of the consignment
!
The display surface of the LCD monitor is sensitive to pressure and scratches. Always
hold the device by the casing!
►Unpack all the individual parts.
►Check the delivery for damage incurred during transportation.
►Check whether the delivery agrees with the details in the delivery note.
The complete LCD monitor package includes:
– one monitor
– one monitor base
– one cover
– one data cable (D-SUB)
– one audio cable
– one power cable
– one CD with Pivot software
– one floppy disk for the monitor picture calibration
– one Warranty Booklet
– this operating manual
Should you discover that the delivery does not correspond to the delivery note, notify your local
sales outlet immediately.
i
It is recommended not to throw away the original packaging material. Keep it for future
transportation.

Colour Monitor SCENICVIEW P17-1A
A26361-K960-Z101-1-5E19 English - 7
Installing an ergonomic video workstation
Before you set up your equipment, you should select a suitable position for working at the monitor.
Please observe the following advice when installing a video workstation.
1
600 mm 600 mm
1
22
1 = Windows
Avoid direct and reflected glare.
Avoid glare from electric
lighting. 1 = Edge of desk
2 = Permissible reaching
sector
Position the keyboard where it
is easiest to reach.
30°
30°
65°
65°
0°
60°
1
22
1
2
1 = Preferable viewing sector
2 = Permissible viewing sector
Position the monitor for
optimum viewing. The viewing
distance to the monitor should
be approximately 50 cm.
Keep ventilated areas clear. 1 = approx. 90° and more
2 = approx. 90°
Remember to maintain correct
posture.
Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available
from specialised dealers, may be advisable. For this purpose the monitor base must be removed
beforehand as described in "Mounting and removing the monitor base" chapter.

Colour Monitor SCENICVIEW P17-1A
8 - English A26361-K960-Z101-1-5E19
Mounting and removing the monitor base
!
The monitor surface is susceptible to scratching! Therefore, lay the monitor on a soft
surface when mounting or removing the monitor base.
Mounting/removing lower section of monitor base
When delivered the lower section of the monitor base is removed. If you do not want to use a
swivelling arm or a wall mounting, you must mount the lower section of the monitor base.
1
Mounting lower section of monitor base
►Lay the monitor on its face on a soft
surface.
►Push the lower section of the monitor base
in the upper section until it engages.
Removing lower section of monitor base
If you want to pack the monitor, you must
remove the lower section of the monitor base.
►Lay the monitor on its face on a soft
surface.
►Press on the release button (1) and pull off
the lower section.
Removing entire monitor base
Before you can use a swivel arm or a wall bracket, you must remove the entire monitor base:
!The monitor surface is susceptible to scratching!
►Switch off the monitor and pull the power plug out of the power socket.

Colour Monitor SCENICVIEW P17-1A
A26361-K960-Z101-1-5E19 English - 9
►Lay the monitor on its face on a soft
surface.
►Remove the cover and disconnect all
cables.
►Remove the four screws on the rear of the
monitor.
You can now mount a swivel arm or a wall
bracket as per VESA FPMPMI with 100 mm hole
spacing.
Note on mounting a swivel arm or a wall bracket
For instructions on how to mount the swivel arm or wall bracket, please see the documentation for
the swivel arm or wall bracket.
We recommend always operating the monitor in the standard position (4:3, wide format, landscape
mode).
!
If you want to operate the monitor with a swivel arm or wall bracket in the portrait mode, it
may only be turned by 90° clockwise.
Permissible position of monitor in portrait mode:
The buttons of the control panel are located on
the left-hand side.

Colour Monitor SCENICVIEW P17-1A
10 - English A26361-K960-Z101-1-5E19
Connecting the monitor
!
Observe the "Safety notes" in the "Important notes" chapter in this operating manual.
CE conformance and optimum picture quality are guaranteed only if you use the data
cable supplied.
Do not cover the ventilation openings of the monitor.
The computer power plug must be pulled out!
►Be sure that the monitor and the computer are switched off.
Connecting cables to the monitor
The monitor ports are protected by a cover. The cover is not attached on delivery.
3
4
5
6
1 2
1 = Cover
2 = Security slot for "Kensington Lock"
3 = Power connector
4 = D-SUB connector (ANALOG)
5 = Headphones port
6 = AUDIO-IN connector
The data cable supplied has two 15-pin D-SUB connectors for connection to the monitor and to the
computer.
►Connect one of the connectors of the data cable to the D-SUB connector on the monitor (4)
and secure the plug-in connection by tightening the safety screws.
►Insert one plug of the audio line in the AUDIO IN (6) socket on the monitor and make sure it is
properly engaged.
►Plug the power cable supplied into the power connector (3) of the monitor.
►Mount the cover (1) over the connections.
i
A lock (Kensington Lock) can be mounted in the security slot (2) to protect the monitor
from theft. A Kensington Lock is not included in the consignment of the monitor.

Colour Monitor SCENICVIEW P17-1A
A26361-K960-Z101-1-5E19 English - 11
Connecting cables to the computer
Information on the computer connections and interfaces is contained in the operating manual for
your computer.
i
If your computer has two monitor ports ("onboard" screen controller and separate
graphics card), the monitor port for the separate graphics card is usually active.
►Connect the data cable to the (active) monitor port on the computer and secure the plug-in
connection by tightening the safety screws.
►Insert the other plug of the audio line in the audio output of the computer.
►Plug the connector of the mains cable provided into the monitor outlet of the computer or into a
properly earthed outlet and ensure a safe connection.
►Plug the power connector of the computer into a properly grounded mains outlet.
i
When you start working with your monitor for the first time you should install the
appropriate graphics drivers for your application software. Details of how to do this are
provided in the documentation on your screen controller/the associated driver software.

Colour Monitor SCENICVIEW P17-1A
12 - English A26361-K960-Z101-1-5E19
Operation of the monitor
The monitor offers the following possibilities that enable it to be optimally adjusted for the respective
user and the respective situation.
Adjusting height, rake and rotation
The monitor height can be adjusted within a range of approx. 2.5 inch/50 mm.
►Grasp the monitor with both hands on the right and left edge of the casing and move it upward
or downward.
15°
5°
90°
The rake of the monitor can be adjusted by -5°
(forward) and +15° (back) from its vertical
position.
►Grasp the monitor with both hands on the
right and left edge of the casing and adjust
it to the desired rake.
The monitor can be turned 90 horizontally in a
clockwise direction from its central position.
►Grasp the monitor with both hands on the
right and left edge of the casing and rotate
it into the desired position.
Adjusting portrait format
The monitor can be turned from the "wide format" (landscape mode) into the "high format" position
(portrait mode).
►Grasp the monitor with both hands on the right and left edge of the casing, move it into the
highest position and turn it clockwise until it is in the portrait position.
i
You must use corresponding software (pivot software) so that the screen display is also
shown in the portrait mode. This software is included in the delivery (CD-ROM) and must
be installed on your computer.
In the OSD menu you have the option of switching the OSD manually from landscape
mode into portrait mode (see also the section "Monitor settings using the OSD menu").
To reset the monitor to the landscape mode, the monitor must be turned counter-clockwise. The
OSD display can be reset again in the OSD menu.