Fujitsu Siemens Computers PRIMERGY Econel 200 User manual

PRIMERGY
PRIMERGY Econel 200
Server System
Operating Manual
Gottfried Staubach/Xenia Fierley
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: [email protected]
Tel.: [phone] / o89-61001-157
Fax: (++49) 700 / 372 00000
A26361-K970-Z102-2-7619
Sprachen: En
Edition September 2005

This manual is printed on
paper treated with
chlorine-free bleach.
Comments Suggestions Corrections
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademar s
Copyright © 2005 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

Introduction
Installation Steps: Overview
Important Notes
Hardware Installation
Preparation for Use and Operation
Property and Data Protection
Problem Solutions and Tips
Abbreviations, Related publications and Index

A26361-K970-Z102-2-7619
Contents
1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Overview of the Documentation . . . . . . . . . . . . . . . . . . 1
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Notational Conventions . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Installation Steps: Overview . . . . . . . . . . . . . . . . . . 11
3 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 FCC Class A Compliance Statement . . . . . . . . . . . . . . 19
3.4 Transporting the Server . . . . . . . . . . . . . . . . . . . . . 20
3.5 Environmental Protection . . . . . . . . . . . . . . . . . . . . 21
4 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Unpacking and Setting up the Server . . . . . . . . . . . . . . 24
4.2 Connecting Devices to the Server . . . . . . . . . . . . . . . . 25
4.2.1 Connecting the Monitor . . . . . . . . . . . . . . . . . . . . . 26
4.3 Connecting the Server to the Line Voltage . . . . . . . . . . . 26
4.4 Hints: Connecting/Disconnecting Cables . . . . . . . . . . . . 28
5 Preparation for Use and Operation . . . . . . . . . . . . . . 29
5.1 Operating and Indicator Elements . . . . . . . . . . . . . . . . 29
5.1.1 The Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1.2 The Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.2 Switching the Server ON/OFF . . . . . . . . . . . . . . . . . . 32
5.3 Configuring the Server . . . . . . . . . . . . . . . . . . . . . . 34
5.3.1 Configuring the SATA RAID Controller . . . . . . . . . . . . . . 34
5.3.2 Configuring the SCSI RAID controller . . . . . . . . . . . . . . 35
5.3.3 Configuration with ServerStart . . . . . . . . . . . . . . . . . . 36
5.3.4 Configuration without ServerStart . . . . . . . . . . . . . . . . 36
5.4 Cleaning the Server . . . . . . . . . . . . . . . . . . . . . . . 37
6 Property and Data Protection . . . . . . . . . . . . . . . . . 39
6.1 Mechanical Access Protection . . . . . . . . . . . . . . . . . . 39
6.2 BIOS Setup Security Functions . . . . . . . . . . . . . . . . . 40
7 Problem Solutions and Tips . . . . . . . . . . . . . . . . . . 41
7.1 Power-on Indicator Remains Dark . . . . . . . . . . . . . . . . 41
7.2 The Server Switches Itself OFF . . . . . . . . . . . . . . . . . 42
7.3 The Monitor Remains Dark . . . . . . . . . . . . . . . . . . . 42

A26361-K970-Z102-2-7619
Contents
7.4 Flickering Stripes Across the Monitor . . . . . . . . . . . . . . . 43
7.5 No Monitor Display or Display Drifts . . . . . . . . . . . . . . . 43
7.6 No Mouse Pointer Displayed on the Monitor . . . . . . . . . . . 43
7.7 Floppy Disk Cannot be Read or Written onto . . . . . . . . . . . 44
7.8 Time and/or Date are Incorrect . . . . . . . . . . . . . . . . . . 44
7.9 RAID „Critical“ Status Condition during Boot . . . . . . . . . . . 45
7.10 System Fails to Boot . . . . . . . . . . . . . . . . . . . . . . . 46
7.11 Drives "dead" at System Boot . . . . . . . . . . . . . . . . . . 46
7.12 Added Drive Defective . . . . . . . . . . . . . . . . . . . . . . 46
7.13 Error Messages on the Monitor . . . . . . . . . . . . . . . . . . 46
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

A26361-K970-Z102-2-7619 1
1 Introduction
The PRIMERGY Econel 200 server is an Intel-based server for workgroups and
small networks. It is suited as a file server as well as an application, information
or internet server.
The PRIMERGY Econel 200 server offers a high degree of reliability and avail-
ability through highly developed hardware and software components.
Security functions in the BIOS Setup and on the system board protect the data
on the server against manipulation. With the RAID levels supported, the hard
disk controllers offer fault tolerance via data redundancy for users who want to
protect valuable data without loss.
1.1 Overview of the Documentation
IPRIMERGY manuals are available in PDF format on the ServerBooks CD.
The ServerBooks CD is part of the ServerView Suite delivered with each
server system.
The PDF files for the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found via the URL:
http://manuals.fujitsu-siemens.com (choose: industry standard servers).
Concept and Target Group of this Manual
This operating manual describes how to install, how to operate and how to
expand your server.
This operating manual is intended for those responsible for installing the
hardware and operating the system. The manual contains all the information
required for mounting and operating your PRIMERGY Econel 200.
To understand the manual, you need a knowledge of hardware and data trans-
mission, as well as a basic knowledge of the operating system used.

2 A26361-K970-Z102-2-7619
Overview of the Documentation Introduction
Additional components of the server documentation
The following additional manuals belong to the PRIMERGY Econel 200
documentation set:
– “Quick Start Hardware - PRIMERGY Econel 200” (poster)
– “Quick Start Software - PRIMERGY ServerView Suite” (poster)
– “Warranty” manual (print version delivered together with the system, PDF file
available on the ServerBooks CD)
– “Safety” manual (print version delivered together with the system, PDF file
available on the ServerBooks CD)
– “Ergonomics” manual (PDF file available on the ServerBooks CD)
– “Helpdesk” (poster with worldwide help desk telephone numbers)
– Technical Manual for the D2020 system board (PDF file available on the
ServerBooks CD)
– “D2020 Setup Utility” manual (PDF file available on the ServerBooks CD)
– “PRIMERGY Econel 200 Server System Options Guide” (PDF file available
on the ServerBooks CD)
IIn the “Options Guide”, the server extension and modification possi-
bilities are described.
– “ServerView Suite” includes the ServerStart CD, the ServerBooks CD and the
ServerSupport CDs. The PDF version of the user manual „PRIMERGY
ServerView Suite - ServerStart“ is also available on the ServerBooks CD.
IIf you need a backup of the ServerBooks CD, send the details of your
server via email address: R[email protected].
– “FastTrak S150 TX4 User Manual” (PDF file available on the
ServerBooks CD)
– “FastTrak S150 TX4 Quick Start Guide” (PDF file available on the
ServerBooks CD)
– “Promise Array Management (PAM) for FastTrak S150 TX2plus, S150 TX4
and TX4000 User Manual” (PDF file available on the ServerBooks CD)
– “LSI SATA Software RAID User’s Guide” (PDF file available on the
ServerBooks CD)

A26361-K970-Z102-2-7619 3
Introduction Overview of the Documentation
– “Global Array Manager Client Software User’s Guide” (PDF file available on
the ServerBooks CD)
– “Global Array Manager Server Software User’s Guide” (PDF file available on
the ServerBooks CD)
– “Integrated Mirroring User’s Guide” (PDF file available on the
ServerBooks CD)
– “Ultra320 SCSI Host Adapters User’s Guide” (PDF file available on the
ServerBooks CD)
Further sources of information
– manual for the monitor
– server management manual ServerView
– in the documentation for the boards and drives
– operating system documentation
– information files of your operating system
(see also “Related publications” on page 53)

4 A26361-K970-Z102-2-7619
Features Introduction
1.2 Features
System board
The features of the system board can be found in the Technical Manual of the
system board for the hardware and in the “D2020 Setup Utility” manual for the
firmware (see “Related publications” on page 53).
Hard disk drives
Two basic configuration variants will be offered for the server: equipped either
with SATA or with SCSI hard disk drives.
Basic configuration with SATA hard disk drives
The drive cage is equipped with up to four SATA hard disk drives with a
maximum height of 1 inch. Each drive is connected to the controller via a cable.
The SATA hard disk drives are controlled by an onboard SATA RAID controller
(up to two drives) or by an optional PCI SATA RAID controller (up to four drives).
Basic configuration with SCSI hard disk drives
The drive cage is equipped with up to four ULTRA320 SCSI hard disk drives with
a maximum height of 1 inch. The drives are connected to the controller via a
cable.
The SCSI hard disk drives are controlled by a PCI SCSI RAID controller.
Onboard SATA RAID Controller
On the system board, a 2-channel SATA RAID controller is integrated for
operating up to two disks. RAID levels 0 and 1 are supported via LSI SATA
Software RAID.
IThe controller has its own configuration utility. For further information see
the “LSI SATA Software RAID User’s Guide” on the ServerBooks CD
(choose Controllers from the menu).

A26361-K970-Z102-2-7619 5
Introduction Features
PCI SATA RAID Controller (FastTrak S150 TX4)
A low-cost and powerful 4-channel SATA RAID controller is optionally available
for operating a maximum of four hard disks, enhancing data security and avail-
ability. RAID levels 0, 1, 10 are supported.
IThe controller has its own configuration utility. For further information see
the “Promise Array Management” manual on the ServerBooks CD (choose
Controllers from the menu).
PCI Ultra320 SCSI controller with Integrated Mirroring Enhanced (IME)
functionality
In the SCSI configuration variant, a 1-channel Ultra320 SCSI controller with
“Integrated Mirroring Enhanced” (IME) functionality (LSI20320A-R) is available
for operating the four SCSI hard disk drives. In addition, IME offers RAID
functionality for the internal disk configuration (RAID levels 1, 1E).
IFor IME configuration, the controller has its own utility. For further infor-
mation see the “Integrated Mirroring User’s Guide” on the ServerBooks CD
(choose Controllers from the menu).
With this controller also a SCSI magnetic tape backup drive can be addressed
additionally to the four SCSI hard disk drives.
Accessible drives
By default, the server has a 3.5-inch floppy disk drive (1.44 MB) and a CD/DVD
drive. In addition, two 5.25-inch slots for accessible drives (CD-ROM, DVD-
ROM, CD/DVD burner or magnetic tape backup drive) are available. The acces-
sible drives cannot be replaced during operation.
Power supply
The server has a fixed power supply unit which automatically adjusts to any
power voltage in the range from 100 V to 240 V.
High level of availability and reliability
When memory data are accessed, 1-bit errors in the main memory are recog-
nized and automatically corrected with the ECC (Error Correcting Code)
method.

6 A26361-K970-Z102-2-7619
Features Introduction
Server management
Server management is implemented with the aid of the supplied ServerView
software.
ServerView enables the management of all PRIMERGY servers in the network
via a central console. Here ServerView supports the following functions:
●Remote startup (Wakeup On LAN)
●Intrusion detection
●Temperature monitoring of the CPU and the surrounding area
●Power monitoring
●End-of-life monitoring of the fans with timely notification before a failure
●Watchdog timer for operating system monitoring and application monitoring
Further information on the ServerView server management is provided in the
associated documentation (see “Related publications” on page 53).
ServerStart
You can configure your PRIMERGY server quickly and precisely with the Server-
Start software provided. User-guided menus are available for installing the
server operating systems.
Service and support
PRIMERGY server are service-friendly and modular, thus enabling quick and
simple maintenance. The flash EPROM program supplied with the Fujitsu
Siemens utilities supports fast BIOS Update.

A26361-K970-Z102-2-7619 7
Introduction Notational Conventions
1.3 Notational Conventions
The following notational conventions are used in this manual:
1.4 Technical Data
Electrical Data (standard power supply)
Italics indicate commands, menu items or software programs.
“Quotation marks” indicate names of chapters and terms that should be
emphasized.
Êtext which follows this symbol describes activities that
must be performed in the order shown.
VCAUTION! pay particular attention to text marked with this symbol.
Failure to observe this warning may endanger your life,
damage the server, or lead to loss of data.
Isupplementary information, remarks, and tips follow
this symbol.
Table 1: Notational Conventions
Rated voltage range 100 - 240 V
Rated frequency 50 Hz - 60 Hz
Rated current in basic configuration: 100 V - 240 V / 1.5 A - 0.6 A
Max. rated current: 100 V - 240 V / 5 A - 2.5 A
AC output (if available) 100 V - 240 V / 2 A
Rated power 453 W
Apparent power 473 VA
Thermal dissipation 1631 kJ/h (1546 btu/h)
Building fuse 16 A
Protection class I

8 A26361-K970-Z102-2-7619
Technical Data Introduction
Compliance Standards
Mechanical Values
Weight
Approx. 21-28 kg (depending on the configuration).
Ventilation Clearance
At least 200 mm on the front and on the rear side.
Product safety and ergonomics IEC 60950 / EN 60950 / UL 60950 3rd. Ed.,
CAN/CSA C22.2 No. 60950 3rd. Ed.
Electromagnetic Compatibility FCC class A
VCCI class A
AS/NZS 3548 class A
CNS 13438
Emitted interference EN 55022 class A
Harmonic current EN 61000-3-2 JEIDA
Flicker EN 61000-3-3
Noise immunity EN 55024
CE label
according to EU directives
Low-Voltage Directive 73/23/EEC
Electromagnetic Compatibility 89/336/EEC
(Product safety)
Width 205 mm
Depth 560 mm
Height 444 mm (with feet)

A26361-K970-Z102-2-7619 9
Introduction Technical Data
Environmental Conditions
Condensation during operation must be avoided.
Noise Level
Environment class 3K2
Environment class 2K2
EN 60721 (IEC 721) section 3-3
EN 60721 (IEC 721) section 3-2
Temperature:
Operation (3K2)
Transport (2K2)
10 °C .... 35 °C
-25 °C .... 60 °C
Relative humidity 10%...85%
Sound power level LWAd (ISO 9296) ≤6.0 B (standby)
≤6.0 B (operation)
Sound pressure level at bystander position
LpAm (ISO 9296) ≤45 dB(A) (standby)
≤45 dB(A) (operating)

A26361-K970-Z102-2-7619 11
2 Installation Steps: Overview
In this chapter you will find an overview of the steps necessary to install your
server system. Links guide you to sections where you can find more detailed
information on the individual steps:
ÊAt first, please take notice of chapter “Important Notes” on page 13ff,
especially of the "Safety" section.
ÊTransport the server to the place where you want to set it up.
ÊUnpack the system, check the contents of the package for visible transport
damage and check whether the delivery agrees with the details in the
delivery note (see section “Unpacking and Setting up the Server” on
page 24).
ÊMake sure all necessary manuals (see section “Overview of the Documen-
tation” on page 1) are available; possibly print of the PDF files.
ÊSet up the server (see section “Unpacking and Setting up the Server” on
page 24).
ÊCable the server. Please also refer to the section “Connecting Devices to the
Server” on page 25 and section “Hints: Connecting/Disconnecting Cables”
on page 28.
ÊConnect the server to the line voltage (see section “Connecting the Server
to the Line Voltage” on page 26).
ÊMake yourself familiar with the operating and indicator elements on the front
and on the rear side of the server (see section “Operating and Indicator
Elements” on page 29).
ÊConfigure and install the desired operating system and applications. To do
so, you have the following possibilities:
– Configuring the SATA RAID controller separately or in a ServerStart
installation (see “Configuring the SATA RAID Controller” on page 34).
– Configuring the SCSI RAID controller separately or in a ServerStart
installation (see “Configuring the SCSI RAID controller” on page 35).

12 A26361-K970-Z102-2-7619
Installation Steps: Overview
– Configuration and installation with or without ServerStart (see section
“Configuration with ServerStart” on page 36 or section “Configuration
without ServerStart” on page 36, respectively).
ITo find out how to operate ServerStart and for further information, refer
to the manual "ServerView Suite - ServerStart" delivered as a PDF
file with the system.

A26361-K970-Z102-2-7619 13
3 Important Notes
In this chapter you will find essential information regarding safety when working
with your server.
3.1 Safety
IThe following safety notes are also provided in the “Safety” manual.
This device complies with the relevant safety regulations for data processing
equipment.
If you have any questions about where you can set up the device, contact your
sales outlet or our customer service team.
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
authorized, qualified staff. Any unauthorized openings and improper
repairs could expose the user to risks (electric shock, energy hazards,
fire hazards) and could also damage the equipment. Please note that
any unauthorized openings of the device will result in the invalidation of
the warranty and exclusion from all liability.

14 A26361-K970-Z102-2-7619
Safety Important Notes
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device (see section
“Technical Data” on page 7).
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.
Installation and operation
VCAUTION!
●The server automatically sets itself to a voltage in the range of 100 V
to 240 V. Make sure that your local voltage is within this range.
●This device has a specially approved power cable and must only be
connected to a grounded insulated socket.
●Ensure that the power socket on the device or the grounded wall
outlet is freely accessible.
●The ON/OFF button does not disconnect the device from the mains
voltage. To disconnect the line voltage completely, switch OFF the
mains power switch (if available) and remove the power plug from the
grounded insulated socket.
●Always connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the central processing unit is still running but the peripheral device
(e.g. storage subsystem) has failed during a power outage.