Fujitsu Siemens Computers PRIMERGY TX200 S4 User manual

PRIMERGY TX200 S4
Server
Options Guide
Edition December 2007

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2007 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.

TX200 S4 Options Guide
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 7
1.2 Overview of the documentation . . . . . . . . . . . . . . . . . 7
1.3 Extensions and conversions . . . . . . . . . . . . . . . . . . 9
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 11
2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 21
4.2 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.2.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 22
4.3 System fans and traverse . . . . . . . . . . . . . . . . . . . 24
4.3.1 Removing the system fan 1 . . . . . . . . . . . . . . . . . . . 24
4.3.2 Removing the system fan 2 . . . . . . . . . . . . . . . . . . . 25
4.3.3 Removing the traverse with the air duct over the main memory . 25
4.3.4 Removing the system fan 3 . . . . . . . . . . . . . . . . . . . 26
5 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2 Extending/replacing the main memory . . . . . . . . . . . . 28

Options Guide TX200 S4
Contents
6 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1 Installing a second processor . . . . . . . . . . . . . . . . . 31
6.2 Replacing the processor . . . . . . . . . . . . . . . . . . . . 35
6.3 Replacing the heat sink . . . . . . . . . . . . . . . . . . . . . 37
7 Accessible drives and LSP . . . . . . . . . . . . . . . . . . . 39
7.1 Installing an accessible 5.25-inch drive . . . . . . . . . . . . 39
7.2 Installing the multibay . . . . . . . . . . . . . . . . . . . . . . 42
7.2.1 Installing a LSP in the multibay . . . . . . . . . . . . . . . . . . 46
7.3 Installing the hard disks extension box . . . . . . . . . . . . 48
8 Expansion boards in the PCI slots . . . . . . . . . . . . . . . 57
8.1 Installing an expansion board . . . . . . . . . . . . . . . . . 58
8.2 Installing a BBU . . . . . . . . . . . . . . . . . . . . . . . . . 61
8.3 Installing the Performance Adapter . . . . . . . . . . . . . . 64
9 SATA SW RAID . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.1 Inserting the RAID key . . . . . . . . . . . . . . . . . . . . . 65
10 Parallel interface for printers . . . . . . . . . . . . . . . . . . 67
10.1 Installing a parallel interface . . . . . . . . . . . . . . . . . . 67
11 Conversion to hot-plug PS and redundant system fans . . . 69
12 Converting from the floorstand model to the rack model . . 81

TX200 S4 Options Guide
Contents
13 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
13.1 System fans and traverse . . . . . . . . . . . . . . . . . . . 85
13.1.1 Installing the system fan 3 . . . . . . . . . . . . . . . . . . . . 85
13.1.2 Installing the traverse with the air duct over the main memory . 86
13.1.3 Installing the system fan 2 . . . . . . . . . . . . . . . . . . . . 86
13.1.4 Installing the system fan 1 . . . . . . . . . . . . . . . . . . . . 87
13.2 Floorstand model . . . . . . . . . . . . . . . . . . . . . . . . 88
13.2.1 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 88
13.3 Rack model . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
13.3.1 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 89
14 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
14.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

TX200 S4 Options Guide 7
1 Introduction
The PRIMERGY TX200 S4 server is an Intel-based server for medium-sized
and large networks. The server is suitable for use as a file server as well as an
application, information, or Internet server. It is available as a floorstand or rack
model. The floorstand model can be converted to a rack model using an optional
conversion kit.
1.1 Concept and target groups
This Options Guide shows you how to extend and upgrade your server.
VCAUTION!
The activities described in this manual may only be performed by
technical specialists.
IThe installation and removal of the hot-plug components is described in
the Operating Manual supplied with the server.
1.2 Overview of the documentation
The PRIMERGY TX200 S4 documentation comprises the following additional
manuals:
– “Quick Start Hardware - PRIMERGY TX200 S4“ poster (only available as
print supplied with the server)
– “Quick Start Software - Quick Installation Guide“ poster (only available as
print supplied with the server
– “Safety notes and other important information” manual
– “Warranty” manual
– “Customer Self Service (CSS)” manual
– “Ergonomics” manual
– “Returning used devices” manual
– “Help desk” leaflet
– Technical Manual for the system board D2509

8 Options Guide TX200 S4
Overview of the documentation Introduction
– Operating Manual for PRIMERGY TX200 S4
– Options Guide for PRIMERGY TX200 S4
– “BIOS-Setup V4.06 / FirstBIOS Desktop Pro V5.0 /
TrustedCoreTM V6.0” manual
– “iRMCS2 - integrated Remote Management Controller” manual
– “LSI SATA Software RAID User’s Guide” manual
– “Integrated RAID for SAS User’s Guide” manual
– “SAS/SATA Controller MegaRAID 1064 / 1068 / 1078 Installation Guide”
manual
IPRIMERGY manuals are available in PDF format on the ServerBooks
DVD. The ServerBooks DVD is part of the ServerStart Suite supplied with
every server.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.fujitsu-siemens.com. The PRIMERGY server documentation
can be accessed using the Industry standard servers navigation option.
You can order a supplementary ServerBooks DVD by sending an e-mail to
the following address, quoting your server data:
[e-mail]
Further sources of information:
– Technical Manual on the relevant rack
– Manual on the monitor
– Documentation on boards and drives
– Documentation on your operating system
– Information files on your operating system

TX200 S4 Options Guide 9
Introduction Extensions and conversions
1.3 Extensions and conversions
Second processor
The system board can be upgraded with a second processor. Only processors
of the same type may be used on the system board. The second processor must
have at least the same clock frequency as the first processor.
Extension of the main memory
Six slots (2 slots form a memory bank) are provided for the main memory. Each
memory bank can be populated with two 512 Mbyte, 1Gbyte, 2Gbyte or 4Gbyte
FDB667/PC2-5300F fully buffered DIMM memory modules.
Additional accessible drives
Three 5.25-inch bays are available for accessible drives. In these bays you can
install DVD/DVD-RW drives, magnetic tape drives, a multibay (slimline DVD and
FDD/ServerView Local Service Panel) or a hard disks extension box.
ServerView Local Service Panel
The system board supports the CSS (Customer Self Service) functionality
(description see the operating manual). You can install a ServerView Local
Service Panel for an easier identification of the defective components.
Hard disks extension box
Two 5.25-inch bays for accessible drives can be used to install a hard disks
extension box.
Two variants of the hard disks extension box are available:
– Variant 1:
one bay for a ServerView Local Service Panel, one bay for a slimline DVD
drive and two bays for 3.5“ hard disks
– Variant 2:
eight bays for 2.5“ hard disks

10 Options Guide TX200 S4
Extensions and conversions Introduction
Additional expansion boards in the PCI slots
The system board offers seven PCI slots:
– 2 x PCI-X slots(64 bit / 133 MHz IOOPTM)
– 4 x PCI-Express slots, Gen1, mechanical PCIe x8
– 1 x PCI slot 32 bit / 33 MHz)
Performance Adapter SNR: S26361-D2504:
The Performance Adapter combines two PCIe x4 slots to one PCIe x8 slot. If
the adapter has been installed in slot 2 (or 7), slot 1 (or 6) can be operated as
PCIe x8.
SATA Software RAID
The SATA SW RAID 5 functionality will be activated by installing a license key
(RAID key).
Parallel interface for printers
As an option, a parallel interface can be provided for printers.
Conversion standard power supply to hot-plug power supply and
standard system fans to redundant system fans
The standard power supply can be replaced by a hot-plug power supply. The
hot-plug power supply consists of two power supply modules.
If one power supply module fails, the other power supply module guarantees the
unrestricted operation and the defective power supply module can be replaced
be replaced while the system is operating (hot-plug).
The standard system fans can be upgraded to redundant system fans. If the
redundant system fans are installed, the fans are operating in a redundant
configuration. A defective system fan can be replaced during the next service.
Conversion of the floorstand model to a rack model
The floorstand model can optionally be converted so that the server can be
integrated into the common rack systems.

TX200 S4 Options Guide 11
Introduction Notational conventions
1.4 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items.
„Quotation marks“ indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.
Table 1: Notational conventions

TX200 S4 Options Guide 13
2Procedure
VCAUTION!
The actions described in these instructions should only be performed by
technical specialists. Equipment repairs should only be performed by
authorized, qualified staff. Any unauthorized opening and improper
repairs could expose the user to risks (electric shock, energy hazards,
fire hazards) and could also damage the equipment. Please note that
any unauthorized opening of the device will result in the invalidation of
the warranty and exclusion from all liability.
ÊFirst of all please familiarize yourself with the safety instructions in the
section chapter “Safety notes” on page 15ff.
ÊEnsure that all required manuals are available, printing out the PDF files if
necessary. You will definitely need the Operating Manual for the server and
the Technical Manual for the system board.
ÊShut down the server correctly, switch it off, pull out the power plug, and
open the server as described in the chapter “Preparation” on page 21ff.
ÊExtend or upgrade your server as described in the relevant chapter.
IThe Operating Manual for the server describes how you
install/remove the hot-plug components.
IProcedures which are identical for the floorstand and rack models are
only described for the floorstand model.
ÊClose the server, connect it to the power outlet, and switch it on as described
in the chapter “Completion” on page 85ff.
ÊStart the operating system and, if necessary, configure it as required (see
the Operating Manual).

TX200 S4 Options Guide 15
3 Safety notes
IThe following safety notes are also provided in the “Safety notes and
other important information” manual.
This device complies with the relevant safety regulations for data processing
equipment. If you have any questions about where you can set up the device,
contact your sales outlet or our customer service team.
VCAUTION!
●The actions described in this manual should only be performed by
technical specialists.
●Repairs to the device that do not relate to CSS errors must only be
carried out by service personnel. Please note that unauthorized inter-
ference with the system will void the warranty and exempt the
manufacturer from all liability.
●Any improper repairs could expose the user to risks (electric shock,
energy hazards, fire hazards) and could also damage the equipment.
Before operating the device
VCAUTION!
●During installation and before operating the device, observe the
instructions on environmental conditions for your device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Transport the device only in the original packaging or in packaging
that protects it from knocks and jolts.

16 Options Guide TX200 S4
Safety notes
Installation and operation
VCAUTION!
●If the rack model is integrated in an installation that receives power
from an industrial (public) power supply network with the IEC309
connector, the (public) power supply protection must comply with the
requirements for the non-industrial (public) power supply networks for
the type A connector.
●The server automatically sets itself to a voltage in the range of
100 V to 240 V. Make sure that your local voltage is within this range.
●This device has a specially approved power cable and must only be
connected to a grounded insulated socket (floorstand model) respec-
tively to a safety socket on the rack mains socket strip (rack model).
●Ensure that the power socket on the device or the grounded wall
outlet is freely accessible.
●The ON/OFF button does not disconnect the device from the mains
voltage. To disconnect the line voltage completely, remove the power
plug from the power socket.
●Always connect the device and the attached peripherals to the same
power circuit. Otherwise you run the risk of losing data if, for example,
the server is still operating but the peripheral device (e.g. storage
subsystem) has failed during a power outage.
●Take notice that the data cables to peripheral devices are adequately
shielded.
●To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●When you set up the floorstand model with hot-plug power supply
units, you should ensure that the supplied anti-tilt bracket is correctly
fitted to prevent tilting.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.

TX200 S4 Options Guide 17
Safety notes
VCAUTION!
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
●In emergencies (e.g. damaged casing, controls or cables, penetration
of liquids or foreign matter), switch off the device immediately, remove
the power plug and contact your sales outlet or customer service
team.
●Proper operation of the device (in accordance with IEC 60950-1/
EN 60950-1) is only ensured if the casing is completely assembled
and the rear covers for the installation openings have been put in
place (electric shock, cooling, fire protection, interference
suppression).
●Install only system expansions that satisfy the requirements and rules
governing safety and electromagnetic compatibility and relating to
telecommunications terminal equipment. If you install other expan-
sions, you may damage the system or violate the safety regulations
and regulations governing RFI suppression. Information on which
system expansions are suitable can be obtained from the customer
service centre or your sales outlet.
●The components or parts marked with a warning label (e.g. lightning
symbol) may only be opened, removed or exchanged by authorized,
qualified personnel. The hot-plug power supply units are exceptions
to this rule.
●The warranty expires if the device is damaged during the installation
or replacement of system expansions.
●You may only set those resolutions and refresh rates specified in the
operating manual of the monitor. Otherwise, you may damage your
monitor. If you are in any doubt, contact your sales outlet or customer
service centre.

18 Options Guide TX200 S4
Safety notes
Batteries
VCAUTION!
●Incorrect replacement of batteries may lead to a risk of explosion. The
batteries may only be replaced with identical batteries or with a type
recommended by the manufacturer (see the technical manual for the
system board).
●Replace the lithium battery on the system board in accordance with
the instructions in the technical manual for the system board.
Working with CDs/DVDs and CD/DVD drives
When working with devices with CD/DVD drives, these instructions must be
followed.
VCAUTION!
●Only use CDs/DVDs that are in perfect condition in your server's
CD/DVD drive, in order to prevent data loss, equipment damage and
injury.
●Check each CD/DVD for damage, cracks, breakages etc. before
inserting it in the drive.
Note that any additional labels applied may change the mechanical
properties of a CD/DVD and cause imbalance.
Damaged and imbalanced CDs/DVDs can break at high drive speeds
(data loss).
Under certain circumstances, sharp CD/DVD fragments can pierce
the cover of the CD/DVD drive (equipment damage) and can fly out
of the device (danger of injury, particularly to uncovered body parts
such as the face or neck).
IYou can prevent mechanical damage and damage to the CD/DVD drive,
as well as premature CD/DVD wear, by observing the following sugges-
tions:
●Only insert CDs/DVDs in the drive when needed and remove them
after use.
●Store the CDs/DVDs in suitable sleeves.
●Protect the CDs/DVDs from exposure to heat and direct sunlight.

TX200 S4 Options Guide 19
Safety notes
ILaser information
The CD/DVD drive complies with IEC 60825-1 laser class 1.
VCAUTION!
The CD/DVD drive contains a light-emitting diode (LED), which under
certain circumstances produces a laser beam stronger than laser
class 1. Looking directly at this beam is dangerous.
Never remove parts of the CD/DVD drive casing!
Modules with electrostatic-sensitive components:
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●Remove the power plug from the power socket before inserting or removing
components containing ESDs.
●You must always discharge static build up (e.g. by touching a grounded
object) before working.
●The equipment and tools you use must be free of static charge.
●Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install components.
●Always hold components with ESDs at the edges or at the positions
highlighted in green (touch points).
●Do not touch any exposed pins or conductors on a component.

20 Options Guide TX200 S4
Safety notes
●Place all components on a static-safe base.
IYou will find a detailed description for handling ESD components in
the relevant European or international standards (DIN EN 61340-5-1,
ANSI/ESD S20.20).