Fujitsu AR G07LL A Series Original operating manual

SPLIT TYPE
ROOM AIR CONDITIONER
Models Indoor unit Outdoor unit
AO*G18LAC2
INVERTER MULTI
SERVICE
INSTRUCTION
R410A
Slim Duct / Compact Cassette
Compact Wall Mounted /
Floor type
AR*G07LL* A
AR*G09LL* A
AR*G12LL* *
AU*G07LVLA
AU*G09LVLA
AU*G12LVL*
AS*G07LJCA
AS*G09LJCA
AS*G12LJCA
AS*G07LUCA
AS*G09LUCA
AS*G12LUCA
AS*G14LUCA
AG*G09LVCA
AG*G12LVCA
AS*G07LMCA
AS*G09LMCA
AS*G12LMCA
AS*G14LMCA

CONTENTS
1. DESCRIPTION OF EACH CONTROL OPERATION
1. CAPACITY CONTROL................................................................................................
3. INDOOR FAN CONTROL...........................................................................................
2. AUTO CHANGEOVER OPERATION..........................................................................
5. OUTDOOR FAN CONTROL.......................................................................................
4. LOUVER CONTROL...................................................................................................
7. COMPRESSOR CONTROL.......................................................................................
6. TIMER OPERATION CONTROL................................................................................
9. TEST OPERATION CONTROL..................................................................................
8. ELECTRONIC EXPANSION VALVE CONTROL........................................................
11. 4-WAY VALVE EXTENSION SELECT.......................................................................
10. PREVENT TO RESTART FOR 3 MINUTES ( 3 MINUTES ST )................................
13. MANUAL AUTO OPERATION...................................................................................
12. AUTO RESTART........................................................................................................
15. POWERFUL OPERATION..........................................................................................
14. COMPRESSOR PREHEATING..................................................................................
16. 10°C HEAT OPERATION...........................................................................................
01-01
01-01
01-03
01-09
01-13
01-14
01-17
01-18
01-18
01-18
01-19
01-19
01-20
01-20
18. DEFROST OPERATION CONTROL.......................................................................... 01-21
01-20
19. OFF DEFROST OPERATION CONTROL.................................................................. 01-23
17. ECONOMY OPERATION........................................................................................... 01-20
20. VARIOUS PROTECTIONS......................................................................................... 01-24
01-19
2-1-2 WIRED REMOTE CONTROLLER DISPLAY......................................................
2-1-1 INDOOR UNIT DISPLAY....................................................................................
2-1 ERROR DISPLAY......................................................................................................
2. TROUBLE SHOOTING
2-2 TROUBLE SHOOTING WITH ERROR CODE..........................................................
2-3 TROUBLE SHOOTING WITH NO ERROR CODE....................................................
2-4 SERVICE PARTS INFORMATION............................................................................
02-01
02-01
02-02
02-32
02-03
02-37
3. REPLACEMENT PARTS

1 . DESCRIPTION OF EACH
CONTROL OPERATION
R410A
INVERTER (MULTI )
Slim Duct / Compact Cassette
Compact Wall Mounted
Floor type

2. AUTO CHANGEOVER OPERATION
01-01
1. CAPACITY CONTROL
1-1 COOLING, HEATING, DRY CAPACITY CONTROL
Compressor frequency decides by capacity of an indoor unit, operation number of an indoor unit,
set temperature, room temperature and outside temperature.
When the air conditioner is set to the Auto mode by remote controller, operation starts in the optimum
mode from among the Heating, Cooling, Dry and Monitoring mode. During operation, the
optimum mode is automatically switched in accordance with temperature changes. The temperature
can be set between 18°C and 30°C in 1°C steps.
When operation starts, indoor fan and outdoor fan are operated for around 3 minutes.
Room temperature and outdoor temperature are sensed,
and the operation mode is selected in accordance with the table below. <Monitoring mode>
Cooling mode
25°C Heating mode
( Table 1 : Operation mode selection table )
Room temperature (TR)
TR> Ts + 2°C
Ts + 2°C TR Ts - 2°C *Middle zone
TR < Ts - 2°C Heating
When Cooling or Dry mode was selected at and air flow mode is Auto, the air conditioner operates as follow.
The same operation as COOLING OPERATION AND DRY OPERATION.
When the room temperature has remained at set temperature -1.5°C,
operation is automatically switched to Dry mode.
If the room temperature reaches set temperature +2°C during Dry mode, operation returns to Cooling.
1
1
2
( Fig. 1 : Outdoor temperature zone selection )
Cooling
(Autmatic dry)
Operation mode
*If it's Middle zone, operation mode of indoor unit is selected as below.
(1). Same operation mode is selected as outdoor unit.
If outdoor unit is operating in Cooling, Dry, and Heating mode,
indoor unit will be operated by the same operation mode.
(2). Selected by the outdoor temperature.
If outdoor unit is operating in other than Cooling, Dry, and Heating mode,
indoor unit will be operated according to the outdoor temperature as below.
Cooling
Cooling Dry(X zone)
Dry(J zone)
Compressor stop
When the room
temperature drops
When the room
temperature rises
Ts + 2°C
Ts - 0.5°C
Ts - 1.5°C
Ts + 1°C
Ts - 1.5°C
Ts - 2.5°C
( Fig.2 : Auto changeover : Cooling - Dry )
TR : Room temperature
Ts : Setting temperature
TR : Room temperature
Ts : Setting temperature
( Air flow mode : Auto )

01-02
START
Room temp.
Ts + 2°C?
COOLING (AUTO:DRY)
OPERATION
HEATING OPERATION
YES
YES
NO
NO
NO
AUTO CHANGEOVER operation flow chart
TS: Setting temperature
Room temp.
Ts - 2°C?
Thermostat remains
in OFF state for 6 minutes or
longer?
System stops
or operation command other than
auto changeover operation?
NO
Thermostat remains
in OFF state for 6 minutes or
longer?
System stops
or operation command other than
auto changeover operation?
Middle zone
NO
Operation mode
of outdoor unit : Cooling or Dry?
YES
NO
Operation mode
of outdoor unit : Heating?
YES
NO
YES
Outdoor temperature
25°C?
NO
YES
YES
NO
YES
YES
When Heating was selected at , the same operation as HEATING OPERATION of page
01-02 is performed.
When the compressor was stopped for 6 consecutive minutes by the temperature control function
after the Cooling(Auto:Dry) or Heating mode was selected at above, operation is switched
to Monitoring and the operation mode is selected again.
31
41

3. INDOOR FAN CONTROL
01-03
1. Fan speed
(Table 2 : Indoor fan speed table)
AS*G07LJCA AS*G09LJCA
AS*G12LJCA AU*G07LVLA
*Note, during Economy operation and operation mode is Fan, air flow is 1 step downs.
(Hi > Me, Me > Lo, Quiet > Soft Quiet)
(rpm) (rpm)
(rpm) (rpm)
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1050
1000
950
850
710
600
480
1050
950
850
680
600
X, J zone:680
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1100
1040
980
850
710
600
480
1100
980
850
680
600
X, J zone:680
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1200
1130
1050
910
710
600
480
1200
1050
880
680
600
X, J zone:680
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
590
570
540
490
440
400
300
590
540
490
440
400
X, J zone:440
AU*G12LVL*
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
650
620
580
520
460
400
300
660
580
520
460
400
X, J zone:460
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
AU*G09LVLA
590
570
540
490
440
400
300
590
540
490
440
400
X, J zone:440
(rpm) (rpm)

AR*G09LL*A (Static pressure:25Pa)
Hi
Me
Lo
Quiet
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
X, J zone:960
1260
1160
1060
960
500
1260
1160
1060
960
500
01-04
AR*G07LL*A (Static pressure:25Pa)
Hi
Me
Lo
Quiet
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
X, J zone:880
1160
1000
940
880
500
1160
1000
940
880
500
(rpm)(rpm)
*Note, during Economy operation and operation mode is Fan, air flow is 1 step downs.
(Hi > Me, Me > Lo, Quiet > Soft Quiet)
AR*G12LL** (Static pressure:25Pa)
Hi
Me
Lo
Quiet
S-Lo
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
X, J zone:1030
1340
1240
1140
1030
500
1340
1240
1140
1030
500
(rpm)
AS*G07LUCA AS*G09LUCA
(rpm) (rpm)
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1030
980
980
910
850
650
610
570
1030
980
910
850
650
610
X, J zone:650
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1080
1030
1030
950
850
650
610
570
1080
1030
950
850
650
610
X, J zone:650

01-05
AG*G09LVCA
Hi
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1120/950
1000/850
860/730
660/560
660/560
660/560
1120/950
960/820
820/700
660/560
570/480
-
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
1230
1090
940
750
680
680
1230
1070
910
750
680
X, J zone:750
Upper & Lower
air flow mode Upper air flow mode
AG*G12LVCA
Hi
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Hi
Me
Lo
Quiet
Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1240/1040
1080/920
910/770
660/560
660/560
660/560
1240/1040
1050/890
860/730
660/560
570/480
-
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
Upper / Lower
1300
1140
980
750
680
680
1300
1120
930
750
680
X, J zone:750
Upper & Lower
air flow mode Upper air flow mode
(rpm)
(rpm)
AS*G14LUCA (rpm)
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1230
1180
1180
1080
1010
790
610
570
1230
1180
1080
980
740
710
X, J zone:740
AS*G12LUCA (rpm)
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1160
1110
1110
1030
930
650
610
570
1160
1110
1030
930
650
610
X, J zone:650

01-05+1
AS*G07LMCA AS*G09LMCA
AS*G12LMCA AS*G14LMCA
*Note, during Economy operation and operation mode is Fan, air flow is 1 step downs.
(Hi > Me, Me > Lo, Quiet > Soft Quiet)
(rpm) (rpm)
(rpm) (rpm)
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1090
1050
1000
950
850
710
600
480
1090
1050
950
850
680
600
X, J zone:680
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1140
1090
1040
980
850
710
600
480
1140
1090
980
850
680
600
X, J zone:680
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1240
1190
1120
1050
910
710
600
480
1240
1190
1050
880
680
600
X, J zone:680
Powerful
Hi
Me+
Me
Lo
Quiet
Cool Air Prevention
S-Lo
Powerful
Hi
Me
Lo
Quiet
*Soft Quiet
Auto
Operation mode
Heating
Cooling / Fan
Dry
Air flow mode Fan Speed
1240
1190
1120
1050
910
710
600
480
1240
1190
1050
880
680
600
X, J zone:680

The airflow can be switched in 5 steps such as Auto, Quiet, Lo, Me, Hi,
while the indoor fan only runs.
When Fan mode is set at (Auto), it operates on (Me) Fan Speed.
2. FAN OPERATION
3. COOLING OPERATION (Auto : Cooling)
Switch the airflow [Auto], and the indoor fan motor will run according to a room temperature,
as shown in Fig 3.
On the other hand, if switched in [Hi] [Quiet], the indoor motor will run at a constant airflow of [Cooling]
operation modes Quiet, Lo, Me, Hi.
( Fig.3 : Airflow change - over (Cooling : Auto) )
When the room
temperature rises
When the room
temperature drops
TR : Room temperature
Ts : Setting temperature
TR-Ts > +2°C
=
+1°C > TR-Ts
+2°C > TR-Ts > +1°C
=
TR-Ts > +2.5°C
=
+1.5°C > TR-Ts
+2.5°C) > TR-Ts > +1.5°C
=
Hi
Me
Lo =
=
=
=
4. DRY OPERATION (Auto : Dry)
During the dry operation, the fan speed setting can not be changed,it operates automatically as shown in Fig. 4.
Room temperature variation which the room temperature sensor of the indoor unit body has detected.
( Fig. 4 : Indoor fan control )
10 30 60 180 60 180 60 10 30 (sec)
Fan OFF
OFF
< Compressor >
ON
Setting air flow
S-Lo
< Indoor fan air flow mode >
< All models >
< All models >
01-06
3-1 INDOOR UNIT FAN CONTROL FOR ENERGY SAVING (Cooling mode)
Switch the airflow at cooling mode, and the indoor fan motor will run as shown in Fig.4.
It depends on the Function setting "Indoor unit fan control for energy saving."

The maximum value of the indoor fan speed is set as shown in Fig 6, based on the detected
temperature by the indoor heat exchanger sensor in heating mode.
< AS*G type >
01-07
5. HEATING OPERATION (Auto : Heating)
Switch the airflow [Auto], and the indoor fan motor will run according to a room temperature,
as shown in Fig 5.
On the other hand, if switched in [Hi] [Quiet], the indoor motor will run at a constant airflow
of [Heat] operation modes Quiet, Lo, Me, Hi, as shown in Table 2.
6. COOL AIR PREVENTION CONTROL (For Heating and Min. Heat operation)
( Fig.5 : Airflow change - over (Heating : Auto) )
TR-Ts > -1.5°C
=
-2.5°C > TR-Ts
-1.5°C > TR-Ts > -2.5°C
=
TR-Ts > -1°C
=
-2°C > TR-Ts
-1°C > TR-Ts > -2°C
=
When the room
temperature rises When the room
temperature drops
TR : Room temperature
Ts : Setting temperature
Lo
Me
Me+
42°C
30°C
34°C
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Hi
*Me+ or setting
FAN mode
Cool air
prevention
39°C
37°C
37°C
32°C
28°C
S-Lo
*Lo or setting
FAN mode
29°C
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
*Lo or setting
FAN mode
37°C 32°C
24°C
*Hi or setting
FAN mode
S-Lo
During NORMAL HEATING OPERATION
< AR*G type >
*Lower speed is selected
Field setting is necessary at AR and AU type as "Cool air prevention : effective"
TR-Ts > -1.5°C
=
-2.5°C > TR-Ts
-1.5°C> TR-Ts > -2.5°C
=
TR-Ts > -1°C
=
-2°C > TR-Ts
-1°C > TR-Ts > -2°C
=
When the room
temperature rises When the room
temperature drops
Lo
Me
Hi
< AU*G / AR*G / AG*G type >
< AS*G type >
( Fig.6 : Airflow change - over for cool air prevention)
*Lower speed is selected

01-08
34°C
< AS*G / AUG type >
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Lo
39°C Auto
When Indoor
heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Lo
Auto
32°C
37°C
During MIN. HEAT OPERATION
< AR*G type >
< AU*G type >
42°C
30°C
34°C
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Hi
*Me+ or setting
FAN mode
Cool air
prevention
39°C
37°C
37°C
32°C
24°C
S-Lo
*Lo or setting
FAN mode
< AG*G type >
*Lower speed is selected
42°C
30°C
31°C
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Hi
*Me or setting
FAN mode
Cool air
prevention
39°C
37°C
34°C
29°C
24°C
S-Lo
*Lo or setting
FAN mode
*Lower speed is selected
31°C
When Indoor heat exchanger
temperature rises When Indoor heat exchanger
temperature drops
Lo
39°C Auto
< AG*G type >

4. LOUVER CONTROL
Each time the button is pressed, the air direction range will change as follow:
(Function Range)
01-09
Use the air direction adjustments within the ranges shown above.
The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.
Cooling / Dry mode : Horizontal flow
Heating mode : Downward flow
When the temperature of the air being blown out is low at the start of heating operation or during
defrosting, the airflow direction temporarily becomes to prevent cold air being blown onto the body.
During use of the Cooling and Dry modes, do not set the Air Flow Direction Louver in the Heating
range ( ) for long period of time, since water vapor many condense near the outlet louvers and
drop of water may drip from the air conditioner. During the Cooling and Dry modes, if the Air Flow
Direction Louvers are left in the heating range for around 30 minutes, they will automatically
return to position .
(Fig.7 : Virtical Air Direction Range)
Cooling / Heating / Dry mode / Fan mode
Cooling / Dry / Fan mode( ) :
Heating / Fan mode( )
2. SWING OPERATION
When the swing signal is received from the remote controller, the vertical louver starts to swing.
(Swinging Range) 1 3 14
466
Vertical Airflow Swing Operation
When the indoor fan is S-Lo or Stop mode, the swing operation is interrupted
and it stops at either upper end or bottom end.
For AS*G07/ 09/ 12LJCA Type
1. VERTICAL LOUVER CONTROL
Vertical Louver
<Compact Wall Mounted Type>
4

1. VERTICAL LOUVER CONTROL
3. SWING OPERATION
Each time the button is pressed, the air direction range will change as follow:
(Function Range)
01-10
The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.
Cooling / Dry mode Horizontal flow
Heating mode Downward flow
When the swing signal is received from the remote controller, the vertical louver starts to swing.
(Fig.8 : Air Direction Range)
Cooling / Dry mode
Fan mode ( )
Types of Air flow Direction Setting:
, , : During Cooling/Dry modes
, , , : During Heating
The Remote Controller's display does not change.
Use the air direction adjustments within the ranges shown above.
During AUTO mode operation, for the first a few minutes after beginning operation,
air-flow will be horizontal 1; the air direction cannot be adjusted during this period.
The air flow direction setting will temporarily become 1 when the temperature of the air -flow is
low at the start of the Heating mode.
Range
Heating mode
Fan mode ( )
The SWING operation may stop temporarily when the air conditioner’s fan is not operating,
or when operating at very low speeds.
1
2
3
4
5
6
7
2. ADJUST THE RIGHT-LEFT LOUVERS
Move the Right-Left louvers to adjust air flow in the direction you prefer.
Knob (2 places)
Right-Left Louvers
Knob
To select Vertical Airflow Swing Operation
To select Horizontal Airflow Swing Operation
(No function)
For AS*G07/ 09/ 12/ 14LUCA Type

1. VERTICAL LOUVER CONTROL
2. SWING OPERATION
Each time the button is pressed, the air direction range will change as follow:
(Function Range)
01-10+1
The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.
Cooling / Dry mode Horizontal flow
Heating mode Downward flow
When the swing signal is received from the remote controller, the vertical louver starts to swing.
(Table11 : Swinging Range)
Air Direction RangeFig.9 :
Cooling / Dry mode
Fan mode ( )
The Remote Controller's display does not change.
Use the air direction adjustments within the ranges shown above.
If you set the angle to position 4.7 for more than 30 minutes in COOL or
DRY mode, they automatically return to position 3.
In COOL or DRY mode, if the angle is set to position 4.7 for many hours,
condensation may be formed, and the drips may wet your property.
During AUTO or Heating mode operation, for the first a few minutes after beginning operation,
air-flow will be horizontal 1; the air direction cannot be adjusted during this period.
The air flow direction setting will temporarily become 1 when the temperature of the air -flow is
low at the start of the Heating mode.
Range
Heating mode
Fan mode ( )
The SWING operation may stop temporarily when the air conditioner’s fan is not operating,
or when operating at very low speeds.
2.ADJUST THE RIGHT-LEFT LOUVER S
Move the Right-Left louvers to adjust air flow
in the direction you prefer.
To select Vertical Airflow Swing Operation
To select Horizontal Airflow Swing Operation
(No function)
Right-Left Louvers
1
234567
Knob
For Wall Mounted Type < AS*G07/09/12/14LMCA>

01-11
1. VERTICAL LOUVER CONTROL
Each time the button is pressed, the air direction range will change as follows:
Use the air direction adjustments within the ranges shown above.
The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.
(Function Range)
(Fig.9 : Air Direction Range)
(Operation Range)
Cooling / Heating / Dry / Fan mode :
Cooling / Dry / Fan mode Horizontal flow
Heating mode Downward flow
2. SWING OPERATION
When the swing signal is received from the remote controller, the vertical louver starts to swing.
The range of swing depends on the set airflow direction.
When the indoor fan is either at S-Lo or Stop mode, the swinging operation is interrupted
and it stops at either upper end or bottom end.
( Stop mode means Operation stop.)
During AUTO mode operation, for the first minute after start-up, air-flow will be horizontal
; the air direction cannot be adjusted during this period.
For AU*G07/ 09/ 12LVLA Type
1234
1234
1
14
4
1
2
3
4
(Swinging Range)
Cooling / Heating / Dry / Fan mode :

01-12
For AG*G09/ 12LVCA Type
1. VERTICAL LOUVER CONTROL
2. SWING OPERATION
Each time the button is pressed,
the air direction range will change as follows:
Use the air direction adjustments within the ranges shown above.
The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.
Cooling / Dry / Fan mode Horizontal flow
Heating mode Downward flow
When the temperature of the air being blown out is low at the start of heating operation or during
defrosting, the airflow direction temporarily becomes to prevent cold air being blown onto the body.
During Monitor operation in AUTO CHANGEOVER mode, the airflow direction automatically
becomes , and it cannot be adjusted.
(Function and Operation Range)
When the swing signal is received from the remote controller, the vertical louver starts to swing .
(Swinging Range)
When the indoor fan is either at S-Lo or Stop mode, the swinging operation is interrrupted
and it stops at either upper end or bottom end.
( Fig.10 : Air Direction Range)
Cooling / Heating / Dry / Fan mode :

5. OUTDOOR FAN CONTROL
Following table 3 shows the fan speed of the outdoor unit.
01-13
1. Outdoor Fan Motor
*It runs at 500rpm for 20 seconds after starting up the outdoor fan.
( Table 3 : Fan speed of the outdoor unit )
900/ 820/ 700/ 410/ 320/ 250/ 200 rpm 900/ 820/ 700/ 410/ 320/ 250/ 200 rpm
Cooling Heating
AO*G18LAC2

6. TIMER OPEARTION CONTROL
1. ON / OFF TIMER
The table 4 shows the available timer setting based on the product model.
OFF timer : When the clock reaches the set time, the air conditioner will be turned off.
Operation mode
Stop mode
Set time of timer
ON timer : When the clock reaches the set time, the air conditioner will be turned on.
Operation mode
Stop mode
Set time of timer
The program timer allows the OFF timer and ON timer to be used in combination one time.
Operation mode
Operation will start from the timer setting (either OFF timer or ON timer) whichever is closest
to the clock's current timer setting.
The order of operations is indicated by the arrow in the remote control unit's display.
SLEEP timer operation cannot be combined with ON timer operation.
( Table 4 : Timer setting )
2. PROGRAM TIMER
Stop mode Stop mode Stop mode
Operation mode Operation mode
Set time Set time Set time Set time
01-14
6-1 WIRELESS REMOTE CONTROLLER
ON TIMER / OFF TIMER PROGRAM TIMER SLEEP TIMER *WEEKLY TIMER
* For AS*G07/ 09/ 12/ 14LUCA Type

3. SLEEP TIMER
Set temperature rises
( Ts : Set temperature )
Stop of operation
Set temperature lowers
( Ts : Set temperature )
Stop of operation
Ts
+1°C
+2°C
Set 60min
Set 30min 30min 30min
01-15
Ts
-1°C
-2°C
-3°C
-4°C
If the sleep is set, the room temperature is monitored and the operation is stopped automatically.
If the operation mode or the set temperature is change after the sleep timer is set, the operation is
continued according to the changed setting of the sleep timer from that time ON.
In the cooling operation mode
When the sleep timer is set, the setting temperature is increased 1°C.
It increases the setting temperature another 1°C after 1 hour.
After that, the setting temperature is not changed and the operation is stopped at the time
of timer setting.
In the heating operation mode
When the sleep timer is set, the setting temperature is decreased 1°C.
It decreases the setting temperature another 1°C every 30 minutes.
Upon lowering 4deg C, the setting temperature is not changed and the operation stops at
the time of timer setting.
4. WEEKLY TIMER (For AS*G07/ 09/ 12/ 14LUCA Type )
This timer function can set operation times of the each day of the week.
All days can be set together,the weekly timer can be used to repeat the timer setting for all of the days.
Setting day Setting day Setting day
ON OFF ON OFF ON OFF
Set time Set time