Fujitsu UTZ-DUWBCA User manual

AIR CONDITIONER
OPTIONAL PARTS
Wind Baffles UTZ-DUWBCA
INSTALLATION MANUAL
1.Safety P ecautions
The “SAFETY PRECAUTIONS” indicated in this operating manua contain important information pertaining to your safety. Be
sure to observe them. For future use, such as re ocating or repairing the unit, request the user to keep this manua together
with the operating manua of the indoor unit.
2.Checking Pa ts
This mark indicates procedures which, if improper y performed, cou d ead to serious injury
or death.
・ This unit contains no user-serviceab e parts. A ways
consu t authorized service personne for repairs.
・ When moving, consu t authorized service personne
for remova and insta ation of this unit.
・ Do not remove existing standard gri for your safety.
Wind baff e is designed for insta ation over the exist-
ing gri . Remova of existing gri wi expose rotating
parts of the fan and can cause injury.
・ Do not ean or p ace any body weight onto the wind
baff e, as an accident cou d occur.
・ Do not touch sharp edges. Sharp edges may cause
persona injury.
・ Disconnect a power to the unit before performing
maintenance or service. E ectrica shock and persona
injury cou d resu t.
・ Do not modify the wind baff e. Any modification may
resu t in persona injury or equipment fai ure.
△
△△
△ ! WARNING
△
△△
△ ! CAUTION
This mark indicates procedures which, if improper y performed, might possib y resu t in persona
harm to the user or damage to property.
・ Fo ow the Operating Manua s of the indoor units for
Usage precautions of air conditioners other than
wind baff es.
・ To avoid damage to refrigerant coi s and e ectronic
components, use extreme care when dri ing screw
ho es and attaching wind baff es.
・ Avoid any short circuits during the insta ation.
・ Do not insert any objects into the wind baff e.
Disruption of airf ow, equipment damage or persona
Injury may occur.
・ P ease use fasteners provided for insta ation,
Using other fasteners may damage the equipment.
・ Prevent any unit wiring from becoming pinched or
cut when insta ing the wind baff e.
Wind baff e : 1 (Q’ty) Se f-tapping Screw #8 x 1/2 : 1 (Q’ty) Insta ation manua : 1 (Q’ty)

3.Installation Dimensions
When the wind baff es are used insta units as shown in the i ustrations be ow. Ensure minimum c earances are met to a wa
or other obstruction. When insta ing mu tip e units, ensure unit minimum c earances are met or exceeded.
Fai ure to provide minimum c earances wi affect unit performance. Nuisance unit cyc ing or premature equipment fai ure may
resu t. For other insta ation c earances, referring to the unit insta ation manua .
(1) One unit Insta ation Unit : in (mm)
(2) Mu tip e unit Insta ation Unit : in (mm)
4.Installation Inst uctions
(1) Remove existing screws as shown in Figure 1. (Do not ose the screws.) Using the same screws, ocate and secure the wind
baff e as shown in Figure 2.
(2) Using the se f-tapping screw provided, secure the wind baff e upper right corner as shown in Figure 3.
IMPORTANT- Use caution when insta ing ALL screws, as they must not be overtightened!
Figure 1 Figure 2 Figure 3
Wa surface
20(500) or more
20(500) or more
Wa surface
20(500) or more 20(500) or more 20(500) or more
20(500) or more
20(500) or more 20(500) or more