Fujitsu Supercomputer PRIMEHPC FX700 User manual

F
U
J
IT
S
U
S
u
p
e
rc
o
m
p
u
t
er
P
R
I
M
E
H
P
C
F
X
70
0
U
p
gr
a
d
e
a
n
d
M
ai
n
te
n
a
n
c
e
M
a
n
u
a
l
FUJITSU Supercomputer
PRIMEHPC FX700
Upgrade and Maintenance
Manual
C120-0090-04EN

Preface
This document describes the upgrade procedures and maintenance of the FUJITSU Supercomputer
PRIMEHPC FX 00:
- Upgrading the configuration by adding optional hardware parts
- Upgrading the configuration by replacing existing hardware parts
- Updating HCP firmware through software operations
- Replacing faulty hardware parts
The work procedures contained in this manual vary in
degree of difficulty. Before assigning work, check the
skill level required for the work.
Before performing work, be sure to read "Work Procedure Classification."
Organization and Contents of This Manual
This document consists of the following chapters and appendix.
Chapter
1 Preliminary Work
This chapter describes the preliminary work before starting upgrade or maintenance work.
Chapter
2 Important Information
This chapter contains important information for using this product correctly and safely.
Chapter
3 Basic Hardware Procedures
This chapter describes the use of
diagnostic information as well as hardware handling procedures.
Chapter
4 Basic Software Procedures
This chapter describes software procedures related to operation, including starting maintenance work,
updating HCP firmware, and collecting system event logs.
Chapter
5 Blade
This chapter describes the handling of the blades.
Chapter
6 PSU (Power Supply Unit)
This chapter
describes the handling of the PSUs (power supply units).
Chapter
FANU (Fan Unit)
This chapter describes the handling of the FANUs (fan units).
Chapter
8 InfiniBand Card
This chapter describes the handling of InfiniBand cards.
Chapter
9 M.2 SSD
This chapter describes the handling of the M.2 SSDs.
Chapter
10 BAREBONE
(Barebones Server)
This chapter describes the handling of the BAREBONE (barebones server).
Chapter
11 BMCIFU
Preface
C120-0090-04ENi

WARNING indicates a hazardous (potentially dangerous) situation that could result in death or
serious personal injury if the product is not used properly.
CAUTION indicates a hazardous situation that could result in minor or moderate personal injury
and/or property damage, such as to the product itself or the user's property, if the product is not used
properly.
Edition Date Changed Location (Change
Classification)(*1)
Description
01 February 27 2020 - Created
02 March 17 2020 Preface
Chapter 2
Chapter 3
Chapter 7
Added "Safety Radio and Harmonics (Europe)"
Added "CE Compliance" to "Regulations"
Added "2.6.1 CE Compliance"
Corrected "3.19 Connecting External Cables"
Corrected "7.2.1 Preliminary Steps"
03 September 25
2020
Chapter 1
Chapter 4
Chapter 5
Chapter 8
Chapter 9
Chapter 10
Appendix A
Updated "Table
1.5 Tools Required and Screws Used for
FX700 Maintenance Work"
Updated "4.2 Updating HCP Firmware"
Updated "4.4 Controlling Nodes"
Updated "5.2.6 Final Steps"
Updated "8.2 Replacing an InfiniBand Card"
Updated "9.2.4 Final Steps"
Updated "10.2.4 Final Steps"
Updated "A.2.1.2 Front Panel Buttons"
This chapter describes the handling of the BMCIFU.
Appendix
A External Views of the Device
This appendix shows external views of the device as well as the LEDs and buttons.
Warning and Important Notice Symbols
This manual uses the following symbols to provide warnings and indicate useful information to the user, to
prevent personal injury and property damage.
Alert Symbols in the Text
An alert statement follows an alert symbol. An alert statement is indented on both ends to distinguish it from
regular text. Similarly, one line is inserted before and after the alert statement.
Revision istory
Preface
C120-0090-04ENii

Edition Date Changed Location (Change
Classification)(*1)
Description
04 November 24, 2020 Preface
Chapter 2
Chapter 4
Chapter 10
Appendix A
Updated "Safety Radio and Harmonics (North America) "
"Safety Radio and Harmonics (Europe) " and "Caution Labels"
Updated "2.1 Installation Precautions"
Updated "4.6.2 Displaying Configuration Information"
Updated "10.1 Basic Information" and "10.2 Replacing the
BAREBONE"
Updated "A.1.3 LANs of the FX700
Main Unit"
*1 The numbers/titles of the chapters/sections to which changes are made are those used in the latest
version. However, the numbers/titles of the chapters/sections with an asterisk are those used in the old
version.
Preface
C120-0090-04ENiii

Safety, Radio, and Harmonics (North America)
Certified
Standard
Standard Number Safety Radio Harmonics
UL ANSI/UL 60950-1, 2nd Ed., 2014-10-14
ANSI/UL 62368-1, 2nd Ed., 2014-12-01
✓
FCC FCC Part-15 Subpart-B (2019) ✓
This section describes the following:
-For Your Safety
-Compliance With Laws and Regulations in Each Country
-Regulations
-Manuals in This Series
-Notation
-Caution Labels
For Your Safety
How to Use This Manual
This manual contains important information required for using this product safely. Read the
FUJITSU
Supercomputer PRIMEHPC FX700 Operating Manual
(C120-0089EN), the
FUJITSU Supercomputer
PRIMEHPC FX700 Getting Starte Gui e
(C120-0093XA), the
FUJITSU Supercomputer PRIMEHPC
FX700 Safety an Regulatory Information
(C120-0092XA), the
FUJITSU Supercomputer PRIMEHPC
FX700 BMC User's Gui e
(C120-0091EN), and the
FUJITSU
Supercomputer PRIMEHPC FX700 Upgra e
an Maintenance Manual
(C120-0090EN) thoroughly before using this product. Before attempting to
operate this device, carefully read and understand each manual, paying particular attention to the safety
precautions.
Be sure to keep this manual in a safe and convenient location for quick reference.
Fujitsu makes every effort
to prevent injury to users and bystanders as well as property damage. Be sure to
use the product in accordance with the instructions in the manual.
Notes on This Product
This product is designed and manufactured for use in standard applications such as office work, personal
devices, and general industrial use. The product is not intended for special uses (nuclear-reactor control in
atomic energy facilities, aeronautic and space systems, air traffic control, operation control in mass transit
systems, life support, or
missile launch controls) where particularly high reliability requirements exist,
where the pertinent levels of safety are not guaranteed, or where a failure, an operational error, or some
other factor could be life-threatening or cause a physical injury (referred to below as "high-risk" use).
Customers considering the use of this product
for high-risk applications must have safety-assurance
measures in place beforehand. Moreover, they are requested to consult our sales representative before
embarking on such specialized use.
Compliance With Laws and Regulations in Each Country
The FX 00 system complies with the laws and regulations listed below.
North America
Safety Precautions
C120-0090-04ENiv

Safety, Radio, and Harmonics (North America) (continued)
Certified
Standard
Standard Number Safety Radio Harmonics
CSA CAN/CSA C22.2 No. 60950-1-0 , 2nd Ed., 2014-10
CAN/CSA C22.2 No. 62368-1-14, 2nd Ed., 2014-12
✓
ICES ICES-003 Issue 6 (201 ) ✓
Environmental Substances (North America)
Standard Number Energy-Saving Environmental
Substances
Recycling
Regulations on brominated flame retardants (Maine,
Washington, Oregon, and Vermont in the U.S.)
✓
Law on emission of perchloric acid compounds to the
environment (California)
✓
Proposition 65 (California) ✓
Prohibition of Certain Toxic Substances Regulations
(SOR/2012-285)
✓
Export Related (North America)
Standard Number
IATA Dangerous Goods Regulations 58th Edition (201 )
(Regulations on transport of lithium, lithium-ion batteries, and electric double layer capacitors)
Foreign Exchange and Foreign Trade Control Law of Japan
North American Free Trade Agreement (NAFTA)
FIPS 140 (Federal Information Processing Standardization 140)
U.S. federal standards that specify security requirements for cryptography modules
NIST SP800-1 1 (U.S.
security standards)
Trade Adjustment Assistance (TAA)
Safety, Radio, and Harmonics (Europe)
Certified
Standard
Standard Number Safety Radio Harmonics
EN, IEC IEC 60950-1:2005 (2nd Ed.); Am1:2009+Am2:2013
EN 60950-1:2006 +A11:2009 +A1:2010+A12:2011+A2:
2013
IEC 62368-1:2014
EN 62368-1:2014 +A11:201
✓
Europe
Safety Precautions
C120-0090-04ENv

Safety, Radio, and Harmonics (Europe) (continued)
Certified
Standard
Standard Number Safety Radio Harmonics
EN 624 9 (2010)
EN 55035 (201 )
EN 55032 (2012); Class A
EN 55024 (2010)
EN 61000-4-2
(2009)
EN 61000-4-3
(2006), +A1, +A2
EN 61000-4-4
(2012)
EN 61000-4-5
(2014), +A1
EN 61000-4-6
(2014)
EN 61000-4-8
(2010)
EN 61000-4-11
(2004), +A1
EN 300 386 V2.1.1 (2016)
✓
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
✓
Environmental Substances and Recycling Disposal (Europe)
Standard Number Energy-Saving Environmental
Substances
Recycling
ErP Directive (2009/125/EC) ✓✓ ✓
RoHS II (2011/65/EU) ✓
New chemical regulation (REACH: No. 190 /2006) ✓
Directive 2006/66/EC of the European Parliament and of
the Council of 6 September 2006 on batteries and
accumulators and waste batteries and accumulators and
repealing Directive 91/15 /EEC
✓
Waste Electrical and Electronic Equipment Directive
(WEEE Directive)
✓
European Parliament and Council
Directive 94/62/EC of
20 December, 1994 on packaging and packaging waste
✓
Export Related (Europe)
Standard Number
IATA Dangerous Goods Regulations 58th Edition (201 )
(Regulations on transport of lithium, lithium-ion batteries, and electric double layer capacitors)
Foreign Exchange and Foreign Trade Control Law of Japan
Customs law of each country
Export Administration Regulations (EAR)
Safety Precautions
C120-0090-04ENvi

Safety, Radio, and Harmonics (Japan)
Certified
Standard
Standard Number Safety Radio Harmonics
PSE Act on Product Safety of Electrical Appliances and
Materials
✓
VCCI VCCI (2016)/VCCI-CISPR 32 (2016) ✓
-JIS C 61000-3-2 (2019) ✓
Energy-Saving, Environmental Substances, and Recycling Disposal (Japan)
Standard Number Energy-Saving Environmental
Substances
Recycling
Act on the Rational Use of Energy ✓
Law Concerning the Examination and Regulation of
Manufacture, etc. of Chemical Substances
✓
Act on Promotion of Procurement of Eco-Friendly Goods
and Services by the State and Other Entities (Act on
Promoting Green Procurement)
✓
Act on the Promotion of Effective Utilization of Resources
✓
Export Related (Japan)
Standard Number
IATA Dangerous Goods Regulations 58th Edition (201 )
(Regulations on transport of lithium, lithium-ion batteries, and electric double layer capacitors)
Fundamental notices of customs law
Safety, Radio, and Harmonics (South Korea)
Certified
Standard
Standard Number Safety Radio Harmonics
KCC K 60950-1 (2.0) (2011-12)
(PSU only)
✓
KN32 Class A
KN35
KN61000-4-2/3/4/5/6/8/11
✓
Recycling and Disposal (South Korea)
Standard Number Energy-Saving Environmental
Substances
Recycling
Display rules on package separation ✓
Japan
South Korea
Safety Precautions
C120-0090-04ENvii

Export Related (South Korea)
Standard Number
IATA Dangerous Goods Regulations 58th Edition (201 )
(Regulations on transport of lithium, lithium-ion batteries, and electric double layer capacitors)
Foreign Exchange and Foreign Trade Control Law of Japan
Export Administration Regulations (EAR)
Safety, Radio, and Harmonics (Australia New Zealand)
Certified
Standard
Standard Number Safety Radio Harmonics
RCM IEC 60950-1:2005 (2nd Ed.); Amd1+ Amd2 with AU,NZ
deviation
✓
AS/NZS CISPR 32 (2013) ✓
Export Related (Australia New Zealand)
Standard Number
IATA Dangerous Goods Regulations 58th Edition (201 )
(Regulations on transport of lithium, lithium-ion batteries, and electric double layer capacitors)
Foreign Exchange and Foreign Trade Control Law of Japan
Export Administration Regulations (EAR)
This equipment is Class A information technology equipment. Operation of this equipment in a
residential area may cause radio interference, in which case the user may be required to
correct the interference at the user's own expense.
VCCI-A
Australia New Zealand
Regulatory Compliance Statements
The applicable regulatory compliance statements provided for this product are as follows:
- Voluntary Control Council for Interference (VCCI) - Japan
Be sure to read the notices on this product before installing the product.
The notices on the product are shown below.
- VCCI Class A Notice
Regulations
This section describes the applicable regulations.
Safety Precautions
C120-0090-04ENviii

The system complies with the requirements of European regulations.
This product is a Class A product. Operation of this product in a residential area may cause radio
frequency interference,
in which case the user will be required to correct the interference at the user's own expense.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules, and meets all requirements of the Canadian Interference-
Causing Equipment Standard (ICES-003) for digital apparatus. These regulations are designed to
provide reasonable protection against radio
interference when the equipment is operated in a
residential installation. This product generates, uses, and can radiate radio frequency energy and, if
not installed and used in strict accordance with the instructions, may cause harmful interference to
radio communications. However, there is no warranty that interference will not occur in the
conditions
at a particular installation. If the product causes harmful interference to radio or television reception
(which can be confirmed by switching the equipment on and off), the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving
antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit separate from that connected to the receiver.
- Consult a reseller or experienced radio/TV technician for support.
Fujitsu is not responsible for any radio or television interference caused by unauthorized modification
of this equipment or the substitution or attachment of connecting cables and equipment other than
those specified by Fujitsu. The user shall be responsible for correcting the interference caused by
such unauthorized modification, substitution, or attachment.
The use of shielded I/O cables is required when connecting the equipment to any optional
peripheral
or host device. Failure to use shielded I/O cables may violate FCC and ICES regulations.
Document Manual Code Description
FUJITSU Supercomputer
PRIMEHPC FX700 Operating Manual
C120-0089EN Contains information about how to install, set up, and
operate the device. (Provided online)
CE Compliance
FCC Class A Declaration of Conformity
The device may be marked with an FCC declaration, which would apply to the equipment covered in this
document unless otherwise specified herein. The declaration for other products will appear in the
accompanying documentation.
Manuals in This Series
The documentation can be found online.
For the Japanese market
https://www.fujitsu.com/jp/products/computing/servers/supercomputer/downloads/
For the global market
https://www.fujitsu.com/global/products/computing/servers/supercomputer/documents/
See the following table for an overview of the documentation.
Safety Precautions
C120-0090-04ENix

Document Manual Code Description
FUJITSU Supercomputer
PRIMEHPC FX700 Upgra e an
Maintenance Manual
C120-0090EN
Contains device upgrade procedures and replacement
procedures for faulty hardware. (Provided online)
FUJITSU Supercomputer
PRIMEHPC FX700 BMC User's
Gui e
C120-0091EN Contains information about the BMC (Baseboard
Management Controller), which manages the
condition of the device. (Provided online)
FUJITSU Supercomputer
PRIMEHPC FX700 Safety an
Regulatory Information
C120-0092XA Contains important safety information. (Provided
online and as print version)
FUJITSU Supercomputer
PRIMEHPC FX700 Getting
Starte
Gui e
C120-0093XA Describes how to access the reference manuals and
other important information after unpacking the
equipment. (The manual is supplied with the product.)
Font or Symbol Meaning Example
AaBbCc123 Indicates
what is input by users and displayed on
screens.
This font is used to indicate command input examples.
# adduser jsmith
AaBbCc123 Indicates
the names of commands, files, and directories
output by the computer and displayed on screens.
This font is used to indicate command output examples
in boxes.
Shell> showinfo
・
・
M.2 Slot Device Status: PASS
Italics Indicates
the name of a referenced manual. See the
FUJITSU Supercomputer
PRIMEHPC FX700 BMC User's Gui e.
" " Indicates the title of a referenced chapter, section, or
subsection.
See "Chapter 4 Operation."
Never peel off the labels.
Storage of Accessories
Keep the accessories in a safe place because they are required for FX 00 main unit operation.
Notation
This document uses the following fonts and symbols to indicate special meanings.
Caution Labels
Caution labels are affixed to this product.
Safety Precautions
C120-0090-04ENx

Main Unit (Top)
Trademarks
- Company names and product names are the trademarks or registered trademarks of their respective
owners.
- Trademark indications (TM, (R)) are omitted for some system and product names in this document.
This document shall not be reproduced or copied without the permission of the publisher.
All Rights Reserved, Copyright FUJITSU LIMITED 2020
Safety Precautions
C120-0090-04ENxi

Ask a certified service engineer or our sales representative to perform the inspection and repair work
for this product and the optional products provided by Fujitsu. The work must not be done by the
customer under any circumstances. Otherwise, electric shock, injury, or fire may result.
Modifying this product or recycling and using a secondhand product may result in personal injury to
users and/or bystanders or damage to the product and/or other property.
Notes on Product Handling
Maintenance
Modifying or Recycling the Product
Disposal or Recycling of Products That ave Completed Their Life Cycle
Waste must be disposed of in a professional and responsible way in accordance with environmental
regulations. For details, please contact your nearest environmental authority or our sales representative.
andling Lithium Batteries
This product uses lithium batteries. Under no circumstances are customers to replace the batteries. The
work must not be done by the customer under any circumstances. Otherwise, a battery may burst or
explode.
Notes on Product Handling
C120-0090-04ENxii

Contents
Preface ……………………………………………………………………………………… i
Notes on Product Handling ……………………………………………………………… xii
Chapter 1 Preliminary Work ……………………………………………… 1
1.1 Work Procedure Classification …………………………………………………………… 1
1.1.1 Customer Replaceable Unit (CRU) ………………………………………………………… 1
1.1.2 Field Replaceable Unit (FRU) ……………………………………………………………… 1
1.1.3 Upgrade and Repair Unit (URU) …………………………………………………………… 2
1.2 Work Time ………………………………………………………………………………… 2
1.3 Required Tools …………………………………………………………………………… 3
Chapter 2 Important Information ………………………………………… 4
2.1 Installation Precautions …………………………………………………………………… 4
2.2 Power, Voltage, and Connection Precautions ………………………………………… 5
2.3 Precautions on Handling the FX700 Main Unit ………………………………………… 5
2.4 Precautions on Handling Optional Equipment ………………………………………… 6
2.5 Other Precautions ………………………………………………………………………… 6
2.6 Regulations ………………………………………………………………………………… 6
2.6.1 CE Compliance ……………………………………………………………………………… 6
2.6.2 FCC Class A Declaration of Conformity …………………………………………………
2.7 Environmental Protection ………………………………………………………………… 7
Chapter 3 Basic ardware Procedures ………………………………… 9
3.1 Using Diagnostic Information …………………………………………………………… 9
3.1.1 Identifying the FX 00 Main Unit …………………………………………………………… 9
3.1.2 Determining the Error Level ………………………………………………………………… 9
3.1.3 Identifying a Faulty Part …………………………………………………………………… 9
3.2 Shutting Down the FX700 Main Unit …………………………………………………… 10
3.3 Disconnecting Power Cords ……………………………………………………………… 10
3.4 Disconnecting External Cables …………………………………………………………… 10
3.4.1 Disconnecting External Cables From the Blade ………………………………………… 10
3.4.2 Disconnecting Cables From the BMCIFU ………………………………………………… 10
3.5 Removing the Blade ……………………………………………………………………… 10
3.6 Removing the Dummy Blade ……………………………………………………………… 11
Contents
C120-0090-04ENxiii

3.7 Removing the PSU ………………………………………………………………………… 11
3.8 Removing the Dummy PSU ……………………………………………………………… 11
3.9 Removing the FANU ……………………………………………………………………… 11
3.10 Removing the FX700 Main Unit From the Rack ……………………………………… 12
3.11 Removing the Top Cover ………………………………………………………………… 12
3.12 Installing the Top Cover ………………………………………………………………… 13
3.13 Installing the FX700 Main Unit in the Rack …………………………………………… 14
3.14 Installing the
Blade ……………………………………………………………………… 15
3.15 Installing the Dummy Blade ……………………………………………………………… 15
3.16 Installing the PSU ………………………………………………………………………… 15
3.17 Installing the Dummy PSU ……………………………………………………………… 15
3.18 Installing the FANU ……………………………………………………………………… 15
3.19 Connecting External Cables …………………………………………………………… 16
3.20 Connecting Power Cords ………………………………………………………………… 16
3.21 Powering On the FX700 Main Unit ……………………………………………………… 16
3.22 Handling the Riser Module ……………………………………………………………… 16
3.22.1 Removing the Riser Module (for PCIE#00) ……………………………………………… 1
3.22.2 Installing the Riser Module (for PCIE#00) ……………………………………………… 18
3.22.3 Installing the Slot Cover on the Riser Module …………………………………………… 21
3.22.4 Removing the Slot Cover From the Riser Module ……………………………………… 21
3.23 Removing the Front Bezel ……………………………………………………………… 22
3.24 Installing the Front Bezel ………………………………………………………………… 22
Chapter 4 Basic Software Procedures ………………………………… 23
4.1 Maintenance Work ………………………………………………………………………… 23
4.1.1 Setting Maintenance Mode ………………………………………………………………… 23
4.1.2 Clearing Maintenance Mode ……………………………………………………………… 24
4.1.3 Precaution on Maintenance Mode ………………………………………………………… 25
4.2 Updating HCP Firmware ………………………………………………………………… 25
4.2.1 Registering HCP Firmware ………………………………………………………………… 25
4.2.2 Applying HCP Firmware …………………………………………………………………… 2
4.2.3 Precaution During Updates ………………………………………………………………… 2
4.3 System Event Log (SEL) ………………………………………………………………… 28
4.3.1 Displaying SEL ……………………………………………………………………………… 28
4.3.2 Specifying Filter Conditions ………………………………………………………………… 30
4.3.3 Collecting a Snapshot ……………………………………………………………………… 31
4.3.4 Collecting an Environment Log …………………………………………………………… 33
4.4 Controlling Nodes ………………………………………………………………………… 33
4.4.1 Power Operations …………………………………………………………………………… 33
4.5 Setting the Time …………………………………………………………………………… 36
4.6 Checking the I O Configuration …………………………………………………………… 36
4.6.1 Connecting to the Console ………………………………………………………………… 36
Contents
C120-0090-04ENxiv

4.6.2 Displaying Configuration Information ……………………………………………………… 3
4.7 Installing the OS …………………………………………………………………………… 37
4.8 Installing the InfiniBand Driver …………………………………………………………… 37
Chapter 5 Blade …………………………………………………………… 38
5.1 Basic Information ………………………………………………………………………… 38
5.2 Replacing the Blade ……………………………………………………………………… 39
5.2.1 Preliminary Steps …………………………………………………………………………… 39
5.2.2 Removing the Blade ………………………………………………………………………… 39
5.2.3 Removing the Riser Module and M.2 SSD ……………………………………………… 39
5.2.4 Installing the Riser Module and M.2 SSD ………………………………………………… 40
5.2.5 Installing the Blade ………………………………………………………………………… 40
5.2.6 Final Steps …………………………………………………………………………………… 40
5.3 Adding a Blade …………………………………………………………………………… 40
5.3.1 Preliminary Steps …………………………………………………………………………… 40
5.3.2 Removing the Dummy Blade ……………………………………………………………… 41
5.3.3 Installing the Blade ………………………………………………………………………… 41
5.3.4 Final Steps …………………………………………………………………………………… 41
Chapter 6 PSU (Power Supply Unit) …………………………………… 42
6.1 Basic Information ………………………………………………………………………… 42
6.2 Replacing a PSU …………………………………………………………………………… 43
6.2.1 Preliminary Steps …………………………………………………………………………… 43
6.2.2 Removing the PSU ………………………………………………………………………… 43
6.2.3 Installing the PSU …………………………………………………………………………… 44
6.2.4 Final Steps …………………………………………………………………………………… 45
6.3 Adding a PSU ……………………………………………………………………………… 45
6.3.1 Advance Preparation ……………………………………………………………………… 45
6.3.2 Removing the Dummy PSU ………………………………………………………………… 45
6.3.3 Installing the PSU …………………………………………………………………………… 46
6.3.4 Final Steps …………………………………………………………………………………… 46
Chapter 7 FANU (Fan Unit) ……………………………………………… 47
7.1 Basic Information ………………………………………………………………………… 47
7.2 Replacing a FANU ………………………………………………………………………… 47
.2.1 Preliminary Steps …………………………………………………………………………… 48
.2.2 Removing the FANU ………………………………………………………………………… 48
.2.3 Installing the FANU in the Chassis ………………………………………………………… 50
.2.4 Final Steps …………………………………………………………………………………… 52
Contents
C120-0090-04ENxv

Chapter 8 InfiniBand Card ……………………………………………… 53
8.1 Basic Information ………………………………………………………………………… 53
8.2 Replacing an InfiniBand Card …………………………………………………………… 53
8.2.1 Preliminary Steps …………………………………………………………………………… 53
8.2.2 Removing an InfiniBand Card ……………………………………………………………… 54
8.2.3 Installing an InfiniBand Card ……………………………………………………………… 54
8.2.4 Final Steps …………………………………………………………………………………… 55
8.3 Adding an InfiniBand Card ………………………………………………………………… 56
8.3.1 Preliminary Steps …………………………………………………………………………… 56
8.3.2 Removing a Slot Cover ……………………………………………………………………… 56
8.3.3 Installing an InfiniBand Card ……………………………………………………………… 56
8.3.4 Final Steps …………………………………………………………………………………… 5
Chapter 9 M.2 SSD ………………………………………………………… 58
9.1 Basic Information ………………………………………………………………………… 58
9.2 Replacing an M.2 SSD …………………………………………………………………… 59
9.2.1 Preliminary Steps …………………………………………………………………………… 59
9.2.2 Removing the M.2 SSD …………………………………………………………………… 59
9.2.3 Installing the M.2 SSD ……………………………………………………………………… 60
9.2.4 Final Steps …………………………………………………………………………………… 61
9.3 Adding an M.2 SSD ………………………………………………………………………… 62
9.3.1 Preliminary Steps …………………………………………………………………………… 62
9.3.2 Installing the M.2 SSD ……………………………………………………………………… 62
9.3.3 Final Steps …………………………………………………………………………………… 62
Chapter 10 BAREBONE (Barebones Server) ………………………… 63
10.1 Basic Information ………………………………………………………………………… 63
10.2 Replacing the BAREBONE ……………………………………………………………… 64
10.2.1 Preliminary Steps ………………………………………………………………………… 64
10.2.2 Removing the BAREBONE ……………………………………………………………… 65
10.2.3 Installing the BAREBONE ………………………………………………………………… 65
10.2.4 Final Steps ………………………………………………………………………………… 66
Chapter 11 BMCIFU ……………………………………………………… 67
11.1 Basic Information ………………………………………………………………………… 67
11.2 Replacing the BMCIFU ………………………………………………………………… 67
11.2.1 Preliminary Steps ………………………………………………………………………… 68
11.2.2 Removing the BMCIFU …………………………………………………………………… 68
11.2.3 Installing the BMCIFU ……………………………………………………………………… 0
11.2.4 Final Steps ………………………………………………………………………………… 1
Contents
C120-0090-04ENxvi

Appendix A External Views of the Device ……………………………… 73
A.1 External Views of the Device …………………………………………………………… 73
A.1.1 Front Configuration of the FX 00 Main Unit ……………………………………………… 3
A.1.2 Rear Configuration of the FX 00 Main Unit ……………………………………………… 3
A.1.3 LANs of the FX 00 Main Unit ……………………………………………………………… 4
A.1.4 Internal Configuration of the FX 00 Main Unit …………………………………………… 5
A.1.5 Internal Blade Configuration ……………………………………………………………… 5
A.2 Indicator Lamps and Controls …………………………………………………………… 76
A.2.1 Server Front ………………………………………………………………………………… 6
A.2.2 Server Rear ………………………………………………………………………………… 9
A.2.3 Blade Rear ………………………………………………………………………………… 82
Contents
C120-0090-04ENxvii

Figure Table Contents
Figure Contents
Figure 3.1 Riser Module Numbers (Top View of the Blade) ……………………………… 17
Figure 3.2 Riser Module Guide (for PCIECARD#00) ……………………………………… 20
Figure 3.3 Riser Module Suspended (Problem) …………………………………………… 20
Figure 3.4 Riser Module Not Suspended (No Problem) …………………………………… 21
Figure 4.1 [Maintenance] Screen …………………………………………………………… 24
Figure 4.2 Error Message (at FANU Failure) ………………………………………………… 25
Figure 4.3 [Firmware
Update] Screen ………………………………………………………… 26
Figure 4.4 Confirmation Dialog Box ………………………………………………………… 26
Figure 4.5 Confirmation Dialog Box ………………………………………………………… 27
Figure 4.6 Error Message (at Upload) ……………………………………………………… 28
Figure 4.7 Displayed SEL List ………………………………………………………………… 29
Figure 4.8 Specifying Filter Conditions ……………………………………………………… 30
Figure 4.9 Clicking the [Collect] Button ……………………………………………………… 31
Figure 4.10 Specifying Settings in [Type] and [Encrypt] …………………………………… 31
Figure 4.11 Message Displayed ……………………………………………………………… 32
Figure 4.12 Display During Snapshot Collection …………………………………………… 32
Figure 4.13 Downloading a Snapshot ………………………………………………………… 33
Figure 4.14 Collecting an Environment Log ………………………………………………… 33
Figure 4.15 [Power Control] Screen ………………………………………………………… 34
Figure 4.16 Specifying a Start Mode ………………………………………………………… 34
Figure 4.17 Setting the Date and Time ……………………………………………………… 36
Figure 5.1 Rear Configuration
of the FX700 Main Unit …………………………………… 38
Figure 6.1 PSU Mounting Locations ………………………………………………………… 42
Figure 7.1 Front Configuration of the FX700 Main Unit (Without the Front Bezel) ……… 47
Figure 8.1 Removing an InfiniBand Card …………………………………………………… 54
Figure 8.2 Installing an InfiniBand Card ……………………………………………………… 55
Figure 9.1 M.2 SSD Mounting Locations (Top View
of the Blade) ………………………… 58
Figure 9.2 Removing the M.2 SSD …………………………………………………………… 60
Figure 9.3 M.2 SSD …………………………………………………………………………… 60
Contents
C120-0090-04ENxviii

Figure 9.4 Installing the M.2 SSD …………………………………………………………… 60
Figure 9.5 Securing the M.2 SSD …………………………………………………………… 61
Figure 10.1 BAREBONE of the FX700 Main Unit …………………………………………… 64
Figure 11.1 BMCIFU of the FX700 Main Unit ……………………………………………… 67
Figure 11.2 Removing the BMCIFU (Top View of the FX700 Main Unit) ………………… 69
Figure 11.3 Removing the BMCIFU ………………………………………………………… 69
Figure 11.4 Installing the BMCIFU …………………………………………………………… 70
Figure 11.5 Securing the BMCIFU (Top View of the FX700 Main Unit) ………………… 71
Figure A.1 Front Configuration of the FX700 Main Unit (With the Front Bezel) ………… 73
Figure A.2 Front Configuration of the FX700 Main Unit (Without the Front Bezel) ……… 73
Figure A.3 Rear
Configuration of the FX700 Main Unit …………………………………… 74
Figure A.4 Rear Locations for the LANs of the FX700 Main Unit ………………………… 74
Figure A.5 Internal Configuration of the FX700 Main Unit ………………………………… 75
Figure A.6 Internal FX700 Blade Configuration …………………………………………… 75
Figure A.7 Front Panel LEDs ………………………………………………………………… 76
Figure A.8 Front Panel Buttons ……………………………………………………………… 78
Figure A.9 Locations of the Front LEDs on the FX700 Main Unit ………………………… 79
Figure A.10 BMCIFU LED (ID) ………………………………………………………………… 79
Figure A.11 BMCIFU LAN LEDs ……………………………………………………………… 80
Figure A.12 Hot-Plug PSU LED (AC PSU) ………………………………………………… 81
Figure A.13 Rear LEDs on the Blade ………………………………………………………… 82
Figure A.14 Rear LAN LEDs on the Blade …………………………………………………… 82
Contents
C120-0090-04ENxix