Fujitsu F2MC-8L F202RA User manual

1
PREFACE
Thank you for purchasing the MB2144-222 (QFP-64 (*1) probe for the F2MC-8L series) or the
MB2144-222-01 (QFP-64 (*1) probe header for the F2MC-8L series).
The MB2144-222 probe connects an emulator for the F2MC (*2)-8L to a user system.
The MB2144-222-01 is the same as the MB2144-222 without the MB2144-210A universal cable
assembly.
This manual explains the handling and operation of the probe (MB2144-222) and probe header
(MB2144-222-01). Read this manual carefully before using these products.
*1: The FPT-64P-M06 is the package for the probe and probe header.
*2: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
• The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales representatives before ordering.
• The information, such as descriptions of function and application circuit examples, in this document are presented solely for the
purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper
operation of the device with respect to use based on such information. When you develop equipment incorporating the device
based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no
liability for any damages whatsoever arising out of the use of the information.
• Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license
of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any
third party or does Fujitsu warrant non-infringement of any third-party' s intellectual property right or other right by using such
information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties
which would result from the use of information contained herein.
• The products described in this document are designed, developed and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured,
could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss
(i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life
support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible
repeater and artificial satellite).
Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection
with above-mentioned uses of the products.
•Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
• If any products described in this document represent goods or technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export
of those products from Japan.
©2003 FUJITSU LIMITED Printed in Japan

2
1. Checking the Delivered Product and Accessories
Before using the MB2144-222 or MB2144-222-01, confirm that the following components are
included in the product package.
❍ For the MB2144-222:
•
••
• MB2144-210A (universal cable assembly) (*1): 1
•
••
• MB2144-222-01 (probe header): 1
•
••
• NQPACK064RZ (*2): 1
•
••
• HQPACK064 RZ (*2) (*3): 1
•
••
• Screws for securing the probe header: 4
•
••
• Operation manual in Japanese: 1
•
••
• Operation manual in English (this manual): 1
❍ For the MB2144-222-01:
•
••
• MB2144-222-01 (probe header): 1
•
••
• NQPACK064RZ (*2): 1
•
••
• HQPACK064RZ (*2) (*3): 1
•
••
• Screws for securing the probe header: 4
•
••
• Operation manual in Japanese: 1
•
••
• Operation manual in English (this manual): 1
*1: The MB2144-210A universal cable assembly can be purchased separately.
*2: Manufactured by Tokyo Eletech Corporation.
*3: Four screws for securing the HQPACK are provided with the HQPACK064RZ.
2. Handling Precautions
•
••
• The bypass capacitor for the microcontroller (MCU) and power supply, the jumper plug
for switching the subclock, the jumper plug for switching the C terminal, and two
connectors for connection with the universal cable assembly are mounted on the probe
header. Be sure to read Section 3, "Using the Products," before using the probe header to
prevent incorrect cable connection, which could cause incorrect operation or product
failure.
•
••
• The MB2144-222 and MB2144-222-01 are precision-manufactured to improve
dimensional accuracy and to ensure reliable contact. These products are therefore
sensitive to mechanical shock, and must be handled carefully. To ensure correct use in the
appropriate environment, use the products only as instructed in Section 3, "Using the
Products".
•
••
• Because ports 0 and 1 of the MCU are connected with cables, they are susceptible to
noise. If ports 0 and 1 are used as input ports, drive the element connected to the ports
with a current of 1 to 2 mA when the port outputs an L level voltage. Be careful not to
read ports only with a pull-down resistor connected, because the values may not be
correctly read.

3
3. Using the Products
■ Setting the jumper plug to switch the subclock source
The jumper plug for switching the subclock source on the probe header is used to switch the source
supplying the subclock.
A subclock oscillation circuit of 32.768 kHz is mounted on the probe header to supply the subclock.
Depending on the operating environment, change the setting of the jumper plug to select whether the
subclock is supplied from a user system or from the probe header. When the product is delivered, the
jumper plugs are set to side 1 (the subclock is supplied from a user system).
To supply the subclock from the subclock oscillation circuit on the probe header, set the jumper plugs
to side 3.
The subclock is supplied
from a user system.
The subclock is supplied
from the probe header.
Figure 3-1 Setting the jumper plug to switch the subclock source
WARNING
Electric shock
To prevent an electric shock when setting the jumper plug, turn off the product and any
connected devices and unplug the power cable from the outlet before setting the jumper
plug.

4
■ Setting the jumper plug to switch the C terminal
The jumper plug for switching the C terminal on the probe header is used to switch the C terminal
capacitive-termination.
A 0.1 µF capacitor is mounted on the probe header to perform C terminal capacitive-termination.
Depending on the operating environment, change the setting of the jumper plug to select whether C
terminal capacitive-termination is performed on a user system or on the probe header. When the
product is delivered, the jumper plug is set to side 1 (C terminal capacitive-termination is done on the
user system).
To switch to the capacitor on the probe header, set the jumper plug to side 3.
C terminal capacitive-
termination is performed
on a user system.
C terminal capacitive-
termination is performed
on the probe header.
Figure 3-2 Setting the jumper plug to switch the C terminal
WARNING
Electric shock
To prevent an electric shock when setting the jumper plug, turn off the product and any
connected devices and unplug the power cable from the outlet before setting the jumper
plug.

5
■ Connecting the universal cable assembly
To connect the universal cable assembly and the probe header, connect the two 34-pin connectors of
the universal cable assembly and the two 34-pin connectors on the probe header.
The connectors on the universal cable assembly, and the mounting section of the connectors on the
probe header are marked "A" and "B" to distinguish the connections.
Correctly connect connector A of the universal cable assembly to connector A on the probe header,
and connector B of the universal cable assembly to connector B on the probe header.
Connection to the emulator probe connector
Connect connector A of the universal
cable assembly to connector A on
the probe header and connector B
of the universal cable assembly to
connector B on the probe header.
Universal cable assembly
(MB2144-210A)
Probe header
(MB2144-222-01)
Figure 3-3 Connecting the universal cable assembly and the probe header
WARNING
Electric shock
To prevent an electric shock when connecting the universal cable assembly and the
probe header, turn off the product and any connected devices and unplug the power
cable from the outlet before making the connections.

6
■ Connecting the probe header to a user system
To connect the probe header and the user system, connect the probe header to the NQPACK064RZ
mounted on the user system using the YQPACK064RZ. An index mark (one corner of the
YQPACK064RZ or NQPACK064RZ is clipped) indicates the first pin on the YQPACK064RZ and on
the NQPACK064RZ. Mount the probe header by using the index marks to align the first pins.
After connecting the probe header to the user system, secure the probe header using the supplied
screws. Secure the probe header to the NQPACK064RZ by inserting the screws in the holes drilled
in the four corners of the mounting part of the MCU. Be sure to secure the probe header evenly at
the four corners with the screws. Tightening the screws too much may damage the probe header
and NQPACK064RZ.
*: The NQPACK064RZ and screws for securing the probe header are supplied with the product.
Screws for securing
the probe header
Probe header
User system
YQPACK064RZ
NQPACK064RZ
Figure 3-4 Connecting the probe header to a user system
WARNING
Electric shock
To prevent an electric shock when connecting the probe header and user system, turn
off the product and any connected devices and unplug the power cable from the outlet
before making the connection.

7
■ Mounting the MCU
When mounting the MCU on the user system without connection to an emulator, use the
HQPACK064RZ to secure the MCU.
An index mark (one corner of the NQPACK064RZ or HQPACK064RZ is clipped) indicates the first
pin on the NQPACK064RZ and the HQPACK064RZ. Also, an index mark (●in a depression) on the
MCU indicates the first pin. Align these index marks to mount the MCU. Incorrect alignment of the
first pins (index mark) may damage the MCU, probe header, or user system.
❍ Procedure for mounting the MCU
1. Mount the MCU by aligning the index mark of the MCU with the index mark of the
NQPACK064RZ.
2. Make sure that the MCU is mounted on the NQPACK064RZ, and place the
HQPACK064RZ on the NQPACK064RZ by aligning the index mark of the
HQPACK064RZ with the index mark of NQPACK064RZ.
3. After placing the HQPACK064RZ on the NQPACK064RZ, secure the MCU using the
supplied screws. Be sure to secure the HQPACK064RZ evenly at the four corners with
the screws. Tightening the screws too much may damage the HQPACK064RZ and
NQPACK064RZ.
*: The HQPACK064RZ and NQPACK064RZ are supplied with the product.
The screws for securing the HQPACK are supplied with the HQPACK064RZ.
Screws for securing
the HQPACK
User system
MCU
HQPACK064RZ
NQPACK064RZ
Figure 3-5 Mounting the MCU
WARNING
Electric shock
To prevent an electric shock when mounting the MCU on the user system, turn off the
product and any connected devices and unplug the power cable from the outlet before
mounting the MCU.

8
4. Note on Using the MB2144-222 and MB2144-222-01
A limit exists on the height of components to be mounted on the user board around the probe header
to ensure connection between the probe header and the user system.
Take this limit into consideration when designing a PC board for the user system.
42.0 mm
67.4 mm
Approximately 14 mm
*: The height from the user system to the probe header varies depending on the mating status
of the connection of the NQPACK064RZ and YQPACK064RZ.
Figure 4-1 Probe header dimensions

SS01
-
25002
-
1E
FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM
F2MC-8L
QFP-64 PROBE and PROBE HEADER for MB89690 Series
MB2144-222/MB2144-222-01
OPERATION MANUAL
April 2003 the first edition
Published FUJITSU LIMITED Electronic Devices
Edited Business Promotion Dept.