Fujitsu BroadOne GX4000 R3.0 Series User manual

T101-2293-1,03,02
GX4000 R3.0 Series
E band Impulse Radio System
User Guide
T101-2293-01
Issue 1.03.02
2014 July
FUJITSU LIMITED

01 Issue History
Issue Number
Issue Date
History
1.02.01
9th December, 2013
First issue
1.02.02
30th May, 2014
Second issue 1
Additional figure (Mounting kit)
1.03.01
23th July, 2014
Third issue 1
Reviewed all and revised
Additional figure (Antenna & Scope mounting kit)
1.03.02
23th July, 2014
Third issue 2
Additional table (throughput[RFC2544] ) etc.
02 Scope
This document describes all of the Operation Manual for Fujitsu’s BroadOne GX4000 series
E band Impulse Radio System. Please note that the specifications are subjected to change
without notice due to Fujitsu’s further design improvements.
03 Non-Disclosure
Fujitsu Limited has taken every care that the contents of this document are correct at the time
of going to press. If any errors are found, or any other comments are wished to be made,
Please do not hesitate to contact us.
The contents of this document are protected under copyright and contain commercially and/or
technically confidential information. The content of the document must not be used other than
for purpose for which it was not provided nor may it be disclosed or copied (by authorized
recipient or otherwise) without the prior written consent of an authorized officer of Fujitsu
Limited.

04 Contents
1. System Description
1.1 Overview ………………………………………………………… 1-1
1.2 System Overview ………………………………………………. 1-1
1.3 Ordering Information …………………………………………… 1-4
1.4 General Specification ………………………………………….. 1-14
1.5 Environmental Specification ………………………………….. 1-24
1.6 Power requirement …………………………………………….. 1-29
1.7Reference Data(Throughput) ………………………………….. 1-34
2. Installation & Site Survey
2.1 Overview ………………………………………………………… 2-1
2.2 Installation & Site Survey Guideline ………………………….. 2-1
2.3 Unpacking ……………………………………………………….. 2-3
2.4 Antenna Pole Mounting …………………………………………. 2-4
2.4.1 Antenna Pole Mounting Overview……………………………….2-4
2.4.2 Goods Necessary for Installation……………………………….. 2-5
2.4.3 Mechanical Dimension of Goods……………………………….. 2-6
2.4.4 Breakdown Components of Mounting Kit……………………….2-8
2.4.5 Fixing Mounting Kit to Pole……………………………………….2-9
2.5 Assembly of Connection Material with E-Band IR .…………… 2-15
2.6 Confirmation of Antenna Polarization…….……………………. 2-16
2.7 Assembly of Antenna Base and E-Band IR…….…………….. 2-17
2.8 Cable & Connector ………………………………………………..2-18
2.8.1 Cable and Connector Code necessary for Installation……….. 2-18
2.8.2 Cable and Connector Description………………………………. 2-18
2.8.3 Cable and Connector Used …………………………………..…2-19
2.8.4 Pin Assignment of Connector ………………………………….. 2-21
2.8.5 Cable Connector Location ……………………………………….2-23
2.8.6 Cable Connection with External Equipment ………………..…2-23
2.9 Cable Connection between External Equipment …………..…2-24
2.10 Assembly of Connector …………………………………………. 2-27
2.10.1Optical Connector …………………………………………………2-27
2.10.2Ether Connector …………………………………………………..2-27.
2.10.3I/O Connector ………………………………………………………2-27
2.10.4Power Supply Cable ……………………………………………….2-32
3. Commissioning Test
3.1 Overview …………………………………………………………. 3-1
3.2 Preparation ………………………………………………………. 3-1
3.3 Power Supply ON ……………………………………………….. 3-2
3.4 Starting WebLT ………………………………………………….. 3-2
3.5 Antenna Alignment Guideline ………………………………….. 3-3
3.6 Antenna Alignment Procedure …………………………………. 3-6
3.7 Continuity Test …………………………………………………….3-11
3.8 Applicable/Not Applicable of Menu Tree ……………………… 3-15
4. Maintenance & Trouble Shooting
4.1 Overview …………………………………………………………. 4-1
4.2 Routine Maintenance …………………………………………… 4-1
4.3 Loopback Function ……………………………………………… 4-5
4.4 ODU Removal for Replacement ……………………………….. 4-7
4.5 ODU Replacement ………………………………………………. 4-9
4.6 Firmware Update ………………………………………………… 4-12
4.7 Housekeeping ……………………………………………………. 4-13

5. Web-Based Local Terminal (WebLT)
5.1 WebLT …………………………………………………………….. 5-1
5.2 Getting Started with WebLT ……………………………………. 5-2
5.3 Menu Tree for Ethernet Interface ……………………………….5-8
5.4 Menu Tree for CPRI Interface ………………………………….. 5-10
5.5 WebLT Menu and Description …………………………………. 5-13
Summary …………………………………………………………..5-15
Configuration > Alarm …………………………………………….5-17
Configuration > Radio …………………………………………….5-18
Configuration > System > Information ……………………… 5-19
Configuration > System > IP ………………………………….. 5-20
Configuration > System > NTP ……………………………….. 5-21
Configuration > System > Log Server ……………………….. 5-22
Configuration > Ports ………………………………………. 5-23
Configuration > Security > Switch > Users ……………… 5-24
Configuration > Security > Switch > HTTPS ……………. 5-26
Configuration > Security > Switch > Access Management …5-27
Configuration > Security > Switch > SNMP > System ….. 5-28
Configuration > Security > Switch > SNMP > RMON > History 5-30
Configuration > Spanning Tree >CIST Ports ………………… 5-31
Configuration > Spanning Tree > CIST Ports ……………. 5-32
Configuration > SyncE ………………………………………. 5-33
Configuration > Sync ………………………………………… 5-35
Configuration > MAC Table …………………………………. 5-36
Configuration > VLAN Translation > Ports to Group Mapping 5-38
Configuration > VLAN Translation > VID Translation Mapping 5-39
Configuration > VLANs Membership …………………………… 5-40
Configuration > VLANs > Ports …………………….…………. 5-41
Monitor > Alarm …………………………………………………. 5-43
Monitor > System > Information ……………………………….. 5-44
Monitor > System > Log ………………………………………… 5-46
Monitor > Ports > Traffic Overview ……………………………. 5-47
Monitor > Ports > Detailed Statistics Radio …………………… 5-48
Monitor > Security > Access Management Statistics ………… 5-49
Monitor > Security > Switch > RMON > Statistics ……………. 5-50
Monitor > Security > Switch > RMON > History ……………….5-52
Monitor > Spanning Tree > Bridge Status …………………….. 5-53
Monitor > Spanning Tree > Port Status ……………………….. 5-55
Monitor > Spanning Tree > Port Statistics ……………………. 5-56
Monitor > MAC Table ……………………………………………. 5-57
Monitor > VLANs > VLAN Membership ……………………… 5-58
Monitor > VLANs > VLAN Port ………………………………… 5-59
Monitor > Radio Performance > Current ……………………… 5-60
Monitor > Radio > 15 Minutes ………………………………….. 5-61
Monitor > Radio Performance > 1 Day ………………………… 5-62
Test & Diagnostics > Control …………………………………….5-63
Test & Diagnostics > Ping………………………………………..5-64
Maintenance > Restart Devices ………………………………… 5-65
Maintenance > Factory Default ………………………………….5-66
Maintenance > Software > Upload …………………………….. 5-67
Maintenance > Software > Image Select ……………………… 5-68
Maintenance > FPGA > Upload ………………………………… 5-69
Maintenance > FPGA > Image Select ………………………….5-70
Maintenance > Configuration > Save ………………………….. 5-71

Maintenance > Configuration > Upload …………………….…5-72
Maintenance > Data > CSV Download ……………………….. 5-73
6. Appendix-A: Notice of Licensing ………………………………………….. 6-1

Notes, Notices and Cautions
NOTE: A NOTE indicates important information that helps you make better use of
E-band Impulse Radio Equipment and your System.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data
and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury or
death.
Important
Observe all warnings in the text and on equipment labels regarding high-voltage or high temperature
conditions. The fallowing warnings and figures apply to most FUJITSU product.

.

The contents of this document are subject to change without notice since Fujitsu Limited reserves the right to make changes
in equipment design or components or firmware release roadmap without notice, as progress in engineering or
manufacturing methods may warrant. Neither this document nor any portion thereof, is to be reproduced in any form
whatsoever without written permission from Fujitsu Limited.
Copyright © 2012 Fujitsu Limited. All Rights Reserved.
Microsoft is a registered trademark of the Microsoft Corporation. Windows is a trademark of the Microsoft Corporation.
All other product names mentioned herein are the trademarks of their respective owners.

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-1
1 System Description
1.1 Overview
This chapter describes the system description of BroadOne GX4000
E-band Impulse radio. The main topics covered are:
System Overview
Ordering Information
General Specification
Environmental Specification
Power requirement
1.2 System Overview
Two Types of Signal Interface
Fujitsu BroadOne GX4000 series E-band impulse radio is complete
All-In-One ODU radio employing impulse modulation technology.
Two (2) types of signal interfaces are available, one is Ethernet interface
(10GbE and/or 1GbE) and the other is CPRI (Common Public Radio
Interface) (*1) interface for mobile communication.
Ethernet Interface
Figure 1.1a Ether System-1 (10GbE Optical Interface)
Figure 1.1b Ether System-2 (1GbE Electrical Interface)
70GHz/80 GHz
5 GHz Bandwidth
10GBASE-LR
Network Equipment
10GBASE-LR
Network Equipment
10GbE
Optical
Ethernet: 3.0 Gbit/s
Local
Terminal
10GbE
Optical
70GHz/80 GHz
5 GHz Bandwidth
1GbE
Electrical
1GbE
Electrical
1000BASE-T
Network Equipment
1000BASE-T
Network Equipment
Ethernet: 3.0 Gbit/s

System Description Fujitsu and Fujitsu Customer Use Only
1-2 BroadOne GX4000 Manual (R3.0) issue 1.03
Figure 1.1c Ether System-3 (10GbE Optical & 1GbE Electrical Interface)
Figure 1.1d Ethernet System-4 (L2SW Interface)
CPRI Interface (*1)
Figure 1.1e CPRI Interface
Figure 1.1f CPRI Interface
Note-*1:
The Common Public Radio Interface (CPRI™) is the successful industry cooperation defining the
publicly available specification for the key internal interface of radio base stations between the Radio
Equipment Control (REC) and the Radio Equipment (RE). The Parties cooperating to define the CPRI
Specification are now encompassing Ericsson, Huawei, NEC, Nokia Siemens Networks and Alcatel-
Lucent. Nortel contributed as member of the CPRI cooperation to CPRI Specification versions 1.4, 2.1,
3.0 4.0 and 4.1 and left the cooperation in December 2009
BBU: Base Band Unit for Japan domestic market
RRH: Remote Radio Head for Japan domestic market
70GHz/80 GHz
5 GHz Bandwidth
10GbE
Optical
10GbE
Optical
1000BASE-T
Network Equipment
1000BASE-T
Network Equipment
Ethernet: 3.0 Gbit/s
1000BASE-T
Network Equipment
1000BASE-T
Network Equipment
1GbE
Electrical
1GbE
Electrical
70GHz/80 GHz
5 GHz Bandwidth
Baseband Unit
(BBU)
Remote Radio Head
(RRH)
Local
Terminal
2.4576 Gbit/s (CPRI)
CPRI
2.4576 Mbit/s
Local
Terminal
5 GHz Bandwidth
CPRI
Optical
Radio Equipment
Control (REC)
Remote Radio
Equipment (RRE)
Local
Terminal
2.4576 Gbit/s (CPRI)
Local
Terminal
CPRI
Optical
70GHz/80 GHz
5 GHz Bandwidth
Local
Terminal
1000BASE-LX
Network Equipment
1000BASE-LX
Network Equipment
1000BASE-LX
Network Equipment
1000BASE-LX
Network Equipment
1000BASE-LX
Network Equipment
Ethernet: 3.0 Gbit/s
L2SW
Local
Terminal
L2SW
10GbE
Optical
1GbE
Electrical
1000BASE-LX
Network Equipment

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-3
Features & Performance
Wireless Innovation based on Impulse Radio
70/80 GHz E-Band 1+0 point-to-point radio
Lightweight, small size zero-footprint ODU design
< 3.0 litter and < 3.0 kg
High power amplifier using GaAs Field Effect Transistor (GaAs FET)
Low power consumption (< 20 W / 1+0)
High Capacity Radio
- 3,000 Mbit/s for Ethernet interface
- 2,457.6 Mbit/s for CPRI interface (4 x 614.4 Mbit/s)
Low latency for multimedia application
Transmit Power Control (ATPC/MTPC) available
Read Solomon error correction
Web-based local terminal and EMS compatible SNMP
1-feet or 2-feet cassegrain antenna with fixing material to pole
Application
LTE/WiMAX Backhaul
Fiber Extension
Mobile Backhaul
Local Area Network Extension
Metropolitan Area Networks (MAN)

System Description Fujitsu and Fujitsu Customer Use Only
1-4 BroadOne GX4000 Manual (R3.0) issue 1.03
1.3 Ordering Information
Ordering Guide
< Configuration Tree of GX4000 System per Link >
: Optional item
Figure 2.1a Configuration Tree for Ethernet Interface & DC Feed
L2SW
70G Ether DC
GX4000 System
Ether interface, DC
:70G GX4000 for Ether for station A (B): x 1
Signal interface: 10GBASE-LR & 1000BASE-T
80G Ether DC
:80G GX4000 for Ether for station B (A): x 1
Signal interface: 10GBASE-LR & 1000BASE-T
:L2 Switch module : x 1
Max. 3 1000BASE-LX to 10GBASE-LR
1-feet Antenna
:1-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
2-feet Antenna
:2-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
:DC power cable: x 2
Signal Cable
:Ethernet (electrical or optical) and IO cable: x 1 set
Connector
:Connector for DC power, IO & criping terminal: x 1 set
Power Cable
Optional
:Optional such as Instruction manual & test stand : x 1 set

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-5
: Optional
Figure 2.1b Configuration Tree for Ethernet Interface & AC Feed
L2SW
70G Ether AC
GX4000 System
Ether interface, AC
:70G E-band IR for Ether for station A (B): x 1
Signal interface: 10GBASE-LR & 1000BASE-T
80G Ether AC
:80G E-band IR for Ether for station B (A): x 1
Signal interface: 10GBASE-LR & 1000BASE-T
:L2 Switch module : x 1
Max. 3 1000BASE-LX to 10GBASE-LR
1-feet Antenna
:1-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
2-feet Antenna
:2-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
:AC power cable: x 2
Signal Cable
:Ethernet (electrical or optical) and IO cable: x 1 set
Connector
:Connector for AC power, IO & criping terminal: x 1 set
Power Cable
Optional
:Optional such as Instruction manual & test stand : x 1 set

System Description Fujitsu and Fujitsu Customer Use Only
1-6 BroadOne GX4000 Manual (R3.0) issue 1.03
: Optional item
Figure 2.1c Configuration Tree for CPRI Interface & DC Feed
70G CPRI BBU
GX4000 System
CPRI interface, DC
:70G E-band IR for CPRI BBU for station A (B): x 1
User rate: 2,4576 Mbit/s
80G CPRI RRH
:80G E-band IR for CPRI RRH for station B (A): x 1
User rate: 2,4576 Mbit/s
1-feet Antenna
:1-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
2-feet Antenna
:2-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
:DC power cable: x 2
Signal Cable
:Signal cable for optical CPRI & IO cable: x 1 set
Connector
:Cnnector for DC power, IO & crimping terminal: x 1 set
80G CPRI BBU
:80G E-band IR for CPRI BBU station A (B): x 1
User rate: 2,4576 Mbit/s
70G CPRI RRH
:70G E-band IR for CPRI RRH for station B (A): x 1
User rate: 2,4576 Mbit/s
Power Cable
Optional
:Optional such as instruction manual & test stand: x 1 set
70G CPRI MMF
:80G E-band IR for CPRI MMF station A (B): x 1
User rate: 2,4576 Mbit/s
80G CPRI MMF
:70G E-band IR for CPRI MMF for station B (A): x 1
User rate: 2,4576 Mbit/s

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-7
: Optional item
Figure 2.1d Configuration Tree for CPRI Interface & AC Feed
70G CPRI BBU
GX4000 System
CPRI interface, AC
:70G E-band IR for CPRI BBU for station A (B): x 1
User rate: 2,4576 Mbit/s
80G CPRI RRH
:80G E-band IR for CPRI RRH for station B (A): x 1
User rate: 2,4576 Mbit/s
1-feet Antenna
:1-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
2-feet Antenna
:2-feet cassegrain antenna with fixing materials to pole : x 1
Direct connection with radio equipment without feeder
:AC power cable: x 2
Signal Cable
:Signal cable for optical CPRI & IO cable: x 1 set
Connector
:Cnnector for AC power, IO & crimping terminal: x 1 set
80G CPRI BBU
:80G E-band IR for CPRI BBU station A (B): x 1
User rate: 2,4576 Mbit/s
70G CPRI RRH
:70G E-band IR for CPRI RRH for station B (A): x 1
User rate: 2,4576 Mbit/s
Power Cable
Optional
:Optional such as instruction manual & test stand: x 1 set
70G CPRI MMF
:80G E-band IR for CPRI MMF station A (B): x 1
User rate: 2,4576 Mbit/s
80G CPRI MMF
:70G E-band IR for CPRI MMF for station B (A): x 1
User rate: 2,4576 Mbit/s

System Description Fujitsu and Fujitsu Customer Use Only
1-8 BroadOne GX4000 Manual (R3.0) issue 1.03
Mechanical Configuration
To introduce the GX4000 system, it is necessary to select equipment, proper materials
and cables regarding to the Application Code. Table 2.1 shows the code.
Mounting Pole
GX4000
Optical cable for 10GbE or CPRI interface,
LAN cable & DC/AC power supply / ALM cable
Mechanical Connection of GX4000
No
Indication
Cable
Description
Cable
1
ETH
RJ-45
1GbE electrical or
maintenance port
Ether cable
2
OPT
Ether: 2xLC
CPRI 1-core: 1xSC
CPRI 2-core: 2xLC
Optical IN/OUT
Optical cable
3
MON
Round 8P
Housekeeping
RSL monitoring
IO cable
Monitor cable
4
PWR
DC: Round 4P
AC: Round 3P
DC -48 V
AC: 100 to 240 V
DC power cable
AC power cable
5
FG
M8 bolt
Frame ground
Cassegrain antenna
with antenna fixing
material to pole

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-9
Ordering Code
Table 2.1a Code for GX4000 Equipment
Description
Ordering Code
GX4000 Ether 70G DC
TX=70 GHz & RX=80 GHz band
Ethernet interface, 3.0 Gbps,
2-SMF, DC -48 V
GX4380LE3D
GX4000 Ether 80G DC
TX=80 GHz & RX=70 GHz band
Ethernet interface, 3.0 Gbps
2-SMF, DC -48 V
GX4380UE3D
GX4000 CPRI BBU 70G DC
TX=70 GHz & RX=80 GHz band
CPRI BBU interface, 2.4576 Gbps
1-SMF, DC -48 V
GX4380LB3D
GX4000 CPRI RRH 80G DC
TX=80 GHz & RX=70 GHz band
CPRI RRH interface, 2.4576 Gbps
1-SMF, DC -48 V
GX4380UB3D
GX4000 CPRI BBU 80G DC
TX=80 GHz & RX=70 GHz band
CPRI BBU interface, 2.4576 Gbps
1-SMF, DC -48 V
GX4380UB3D
GX4000 CPRI RRH 70G DC
TX=80 GHz & RX=70 GHz band
CPRI RRH interface, 2.4576 Gbps
1-SMF, DC -48 V
GX4380LR3D
GX4000 CPRI MMF 70G DC
TX=70 GHz & RX=80 GHz band
CPRI MMF interface, 2.4576 Gbps
2-MMF, DC -48 V
GX4380UC3D
GX4000 CPRI MMF 80G DC
TX=80 GHz & RX=70 GHz band
CPRI MMF interface, 2.4576 Gbps
2-MMF, DC -48 V
GX4380LC3D
GX4000 Ether 70G AC
TX=70 GHz & RX=80 GHz band
Ether interface, 3.0 Gbps
2-SMF, AC 100 - 240 V
GX4380LE3A
GX4000 Ether 80G AC
TX=80 GHz & RX=70 GHz band
Ether interface, 3.0 Gbps
2-SMF, AC 100 - 240 V
GX4380UE3A
GX4000 CPRI BBU 70G AC
TX=70 GHz & RX=80 GHz band
CPRI BBU interface, 2.4576 Gbps
1-SMF, AC 100 –240 V
GX4380LB3A
GX4000 CPRI RRH 80G AC
TX=80 GHz & RX=70 GHz band
CPRI RRH interface, 2.4576 Gbps
1-SMF, AC 100 –240 V
GX4380UR3A
E-band CPRI BBU 80G AC
TX=80GHz & RX=70 GHz band
CPRI BBU interface, 2.4576 Gbps
1-SMF, AC100 to 240 V
GX4380UB3A
E-band CPRI RRH 70G AC
TX=70 GHz & RX=80 GHz band
CPRI RRH interface, 2.4576 Gbps
1-SMF, AC 100 to 240 V
GX4380LR3A
GX4000 CPRI MMF 70G AC
TX=70 GHz & RX=80 GHz band
CPRI interface, 2.4576 Gbps
2-MMF, AC 100 –240 V
GX4380UC3A
GX4000 CPRI MMF 80G AC
TX=80 GHz & RX=70 GHz band
CPRI interface, 2.4576 Gbps
2-MMF, AC 100 –240 V
GX4380LC3A

System Description Fujitsu and Fujitsu Customer Use Only
1-10 BroadOne GX4000 Manual (R3.0) issue 1.03
Table 2.1b Code for Antenna
Description
Ordering Code
Cassegrain Antenna, 1-feet
1-feet antenna
Direct connection to GX4000
Including mounting kit
GX4K80ATP11
Cassegrain Antenna, 2-feet
1-feet antenna
Direct connection to GX4000
Including mounting kit
GX4K80ATP12
Table 2.1c Code for DC Power Cable
Description
Ordering Code
DC Power cable, 1 m
DC power supply cable, 1 m
GX4K80CBPD01
DC Power cable, 5 m
DC power supply cable, 5 m
GX4K80CBPD05
DC Power cable, 10 m
DC power supply cable, 10 m
GX4K80CBPD10
DC Power cable, 20 m
DC power supply cable, 20 m
GX4K80CBPD20
DC Power cable, 30 m
DC power supply cable, 30 m
GX4K80CBPD30
DC Power cable, 40 m
DC power supply cable, 40 m
GX4K80CBPD40
DC Power cable, 50 m
DC power supply cable, 50 m
GX4K80CBPD50
DC Power cable, 60 m
DC power supply cable, 60 m
GX4K80CBPD60
DC Power cable, 70 m
DC power supply cable, 70 m
GX4K80CBPD70
DC Power cable, 80 m
DC power supply cable, 80 m
GX4K80CBPD80
DC Power cable, 90 m
DC power supply cable, 90 m
GX4K80CBPD90
DC Power cable, 100 m
DC power supply cable, 100 m
GX4K80CBPD99
Table 2.1d Code for AC Power Cable
Description
Ordering Code
AC Power cable, 1 m
AC power supply cable, 1 m
GX4K80CBPA01
AC Power cable, 5 m
AC power supply cable, 5 m
GX4K80CBPA05
AC Power cable, 10 m
AC power supply cable, 10 m
GX4K80CBPA10
AC Power cable, 20 m
AC power supply cable, 20 m
GX4K80CBPA20
AC Power cable, 30 m
AC power supply cable, 30 m
GX4K80CBPA30
AC Power cable, 40 m
AC power supply cable, 40 m
GX4K80CBPA40
AC Power cable, 50 m
AC power supply cable, 50 m
GX4K80CBPA50
AC Power cable, 60 m
AC power supply cable, 60 m
GX4K80CBPA60
AC Power cable, 70 m
AC power supply cable, 70 m
GX4K80CBPA70
AC Power cable, 80 m
AC power supply cable, 80 m
GX4K80CBPA80
AC Power cable, 90 m
AC power supply cable, 90 m
GX4K80CBPA90
AC Power cable, 100 m
DC power supply cable, 100 m
GX4K80CBPA99

Fujitsu and Fujitsu Customer Use Only System Description
BroadOne GX4000 Manual (R3.0) issue 1.03 1-11
Table 2.1e Code for Ether Electrical Cable
Description
Ordering Code
Ether electrical cable, 1 m
Ether cable, 1 m
GX4K80CBET01
Ether electrical cable, 5 m
Ether cable, 5 m
GX4K80CBET05
Ether electrical cable, 10 m
Ether cable, 10 m
GX4K80CBET10
Ether electrical cable, 20 m
Ether cable, 20 m
GX4K80CBET20
Ether electrical cable, 30 m
Ether cable, 30 m
GX4K80CBET30
Ether electrical cable, 40 m
Ether cable, 40 m
GX4K80CBET40
Ether electrical cable, 50 m
Ether cable, 50 m
GX4K80CBET50
Ether electrical cable, 60 m
Ether cable, 60 m
GX4K80CBET60
Ether electrical cable, 70 m
Ether cable, 70 m
GX4K80CBET70
Ether electrical cable, 80 m
Ether cable, 80 m
GX4K80CBET80
Ether electrical cable, 90 m
Ether cable, 90 m
GX4K80CBET90
Table 2.1f Code for IO Cable
Description
Ordering Code
IO cable, 1 m
IN/OUT cable, 1 m
GX4K80CBAL01
IO cable, 5 m
IN/OUT cable, 5 m
GX4K80CBAL05
IO cable, 10 m
IN/OUT cable, 10 m
GX4K80CBAL10
IO cable, 20 m
IN/OUT cable, 20 m
GX4K80CBAL20
IO cable, 30 m
IN/OUT cable, 30 m
GX4K80CBAL30
IO cable, 40 m
IN/OUT cable, 40 m
GX4K80CBAL40
IO cable, 50 m
IN/OUT cable, 50 m
GX4K80CBAL50
IO cable, 60 m
IN/OUT cable, 60 m
GX4K80CBAL60
IO cable, 70 m
IN/OUT cable, 70 m
GX4K80CBAL70
IO cable, 80 m
IN/OUT cable, 80 m
GX4K80CBAL80
IO cable, 90 m
IN/OUT cable, 90 m
GX4K80CBAL90
IO cable, 100 m
IN/OUT cable, 100 m
GX4K80CBAL99
Table 2.1g Code for Ether Optical Cable
Description
Ordering Code
Ether optical cable, 1 m
2-SMF, single mode, 1 m
GX4K80CB2S01
Ether optical cable, 5 m
2-SMF, single mode, 5 m
GX4K80CB2S05
Ether optical cable, 10 m
2-SMF, single mode, 10 m
GX4K80CB2S10
Ether optical cable, 20 m
2-SMF, single mode, 20 m
GX4K80CB2S20
Ether optical cable, 30 m
2-SMF, single mode, 30 m
GX4K80CB2S30
Ether optical cable, 40 m
2-SMF, single mode, 40 m
GX4K80CB2S40
Ether optical cable, 50 m
2-SMF, single mode, 50 m
GX4K80CB2S50
Ether optical cable, 60 m
2-SMF, single mode, 60 m
GX4K80CB2S60
Ether optical cable, 70 m
2-SMF, single mode, 70 m
GX4K80CB2S70
Ether optical cable, 80 m
2-SMF, single mode, 80 m
GX4K80CB2S80
Ether optical cable, 90 m
2-SMF, single mode, 90 m
GX4K80CB2S90
Ether optical cable, 100 m
2-SMF, single mode, 100 m
GX4K80CB2S99

System Description Fujitsu and Fujitsu Customer Use Only
1-12 BroadOne GX4000 Manual (R3.0) issue 1.03
Table 2.1h Code for CPRI 1-SMF Optical Cable
Description
Ordering Code
CPRI optical cable,1 m
CPRI, 1-SMF, single mode, 1 m
GX4K80CB1S01
CPRI optical cable,5 m
CPRI, 1-SMF, single mode, 5 m
GX4K80CB1S05
CPRI optical cable,10 m
CPRI, 1-SMF, single mode, 10 m
GX4K80CB1S10
CPRI optical cable,20 m
CPRI, 1-SMF, single mode, 20 m
GX4K80CB1S20
CPRI optical cable,30 m
CPRI, 1-SMF, single mode, 30 m
GX4K80CB1S30
CPRI optical cable,40 m
CPRI, 1-SMF, single mode, 40 m
GX4K80CB1S40
CPRI optical cable,50 m
CPRI, 1-SMF, single mode, 50 m
GX4K80CB1S50
CPRI optical cable,60 m
CPRI, 1-SMF, single mode, 60 m
GX4K80CB1S60
CPRI optical cable,70 m
CPRI, 1-SMF, single mode, 70 m
GX4K80CB1S70
CPRI optical cable,80 m
CPRI, 1-SMF, single mode, 80 m
GX4K80CB1S80
CPRI optical cable,90 m
CPRI, 1-SMF, single mode, 90 m
GX4K80CB1S90
CPRI optical cable,100 m
CPRI, 1-SMF, single mode, 100 m
GX4K80CB1S99
Table 2.1i Code for CPRI 2-SMF Optical Cable
Description
Ordering Code
CPRI optical cable,1 m
CPRI, 2-SMF, multi mode, 1 m
GX4K80CB2M01
CPRI optical cable,5 m
CPRI, 2-SMF, multi mode, 5 m
GX4K80CB2M05
CPRI optical cable,10 m
CPRI, 2-SMF, multi mode, 10 m
GX4K80CB2M10
CPRI optical cable,20 m
CPRI, 2-SMF, multi mode, 20 m
GX4K80CB2M20
CPRI optical cable,30 m
CPRI, 2-SMF, multi mode, 30 m
GX4K80CB2M30
CPRI optical cable,40 m
CPRI, 2-SMF, multi mode, 40 m
GX4K80CB2M40
CPRI optical cable,50 m
CPRI, 2-SMF, multi mode, 50 m
GX4K80CB2M50
CPRI optical cable,60 m
CPRI, 2-SMF, multi mode, 60 m
GX4K80CB2M60
CPRI optical cable,70 m
CPRI, 2-SMF, multi mode, 70 m
GX4K80CB2M70
CPRI optical cable,80 m
CPRI, 2-SMF, multi mode, 80 m
GX4K80CB2M80
CPRI optical cable,90 m
CPRI, 2-SMF, multi mode, 90 m
GX4K80CB2M90
CPRI optical cable,100 m
CPRI, 2-SMF, multi mode, 100 m
GX4K80CB2M99