Fulgor Milano Sofia F6IRT365S1 User manual

RANGE TOP 30” - 36” ELECTRIC INDUCTION
USE & CARE MANUAL
GUIDE D’UTILISATION ET D’ENTRETIEN
MANUAL DE USO Y CUIDADO

Dear Customer,
Thank you for purchasing a Fulgor Milano product. Fulgor Milano is
committed to excellence and our signature technologies provide you with
professional tools for your kitchen. One of our central philosophies is
continuous investment in research that is rooted in developing life enhancing
technology. Our goal is to deliver products that are worthy of your family
recipes and that will breathe life into your kitchen, the heart of your home.
We invite you to enjoy your new Fulgor Milano product with same amount
of care and attention that we have put into creating it.
Your Life | Our Passion

EN
1
Pay attention to these symbols present in this manual:
WARNING
• This is the safety alert symbol. This symbol alerts you to
potential hazards that can kill or hurt you and others.
• You can be killed or seriously injured if you don’t follow
these instructions.
READ AND SAVE THESE INSTRUCTIONS.
WARNING
If the information in this manual is not followed exactly, a fire
or explosion may result causing property damage, personal
injury or death.
- Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WARNINGS FOR ELECTRIC INSTALLATION
WARNING
• Installation and service must be performed by a qualified
installer or service agency.
• The models may be powered at 240V or 208V.
CAUTION
• Always disconnect the electrical plug from the wall
receptacle before servicing this unit.
• For personal safety, this appliance must be properly
grounded.
Do not under any circumstances cut or remove the third
(ground) prong from the power cord plug.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment complies with part 18 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. Howere,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interferance to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antennae.
• Increase the distance between the equipment and
receiver.
• Connect the equipment and receiver.
• Connect the equipment into an outlet or a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experience radio/TV
techician for help.
WARNING
Persons with a pacemaker or similar medical device should
exercise caution when using or standing near an induction
unit while it is in operation. The electromagnetic field may
effect the working of the pacemaker or similar medical
device. It is advisable to consult your doctor or the pacemaker
manufacturer about your particular situation.
IMPORTANT: Save these instructions for the local electrical
inspector use.
INSTALLER: Please leave this manual with owner for future
reference.
OWNER: Please keep this manual for future reference.

EN
2
TABLE OF CONTENTS PAGE
1 - Safety Precautions 3
2 -
Rangetop Safety Instructions 4
Safety for the Cooktop 4
Warnings for Electric Installation 4
3 - Features of your Oven 5
4 - Features of your Cooktop 6
5 - Element and Control Setting 8
Control knobs and power level adjusting 8
6 - Advice on cooking 10
7 - Induction Cooktop Operation 11
Before using the cooktop for the first time 11
Power management (for 36” model only) 11
8 - Cookware 13
How INDUCTION heating works 13
Pots and pans and how to use them 13
9 - Cleaning the Cooktop 15
10 - Resolution of operational problems COOKTOP 16
11 - 11 - Assistance or Service 17

EN
3
1 - Safety Precautions
WARNING
When properly cared for, your new rangetop has been
designed to be a safe, reliable appliance. Read all
instructions carefully before using this range. These
precautions will reduce the risk of burns, electric shock,
fire, and injury to yourself and others. When using kitchen
appliances, basic safety precautions must be followed,
including the following:
This appliance must be properly installed and grounded by
a qualified technician. Connect only to properly grounded
outlet. See “Grounding Instructions” found in the Installation
Instructions.
• This appliance should be serviced only by a qualified service
technician. Contact the nearest authorized service center for
examination, repair or adjustment.
• Do not repair or replace any part of the appliance unless
specifically recommended. Refer service to an authorized
servicer.
• Do not operate this appliance if it is not working properly
or if it has been damaged, until an authorized servicer has
examined it.
• Install or locate this appliance only in accordance with the
Installation Instructions.
• Use this rangetop only as intended by the manufacturer. If
you have any questions, contact the manufacturer.
• Do not cover or block any openings on this appliance.
• Use this appliance only for its intended use as described
in this manual. Do not use corrosive chemicals, vapors, or
nonfood products in this appliance. This type of appliance is
specifically designed to heat or cook. It is not designed for
industrial or laboratory use. The use of corrosive chemicals
in heating or cleaning will damage the appliance.
• In the event that personal clothing or hair catches fire, DROP
AND ROLL IMMEDIATELY to extinguish flames.
WARNING
• BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
• Do not use water, including wet dishcloths or towels on
grease fires. A violent steam explosion may result.
• NEVER PICK UP A FLAMING PAN. You may be burned.
• ALWAYS have a working SMOKE DETECTOR near the
kitchen.
• LEAVE THE HOOD VENTILATOR ON when flambéing
food.
To reduce the risk of burn injuries during cooktop
use, observe the following:
• NEVER use this appliance as a space heater to heat or warm
the room.
• Children or pets should not be left alone or unattended in an
area where appliances are in use.
• They should never be allowed to sit or stand on any part of
the appliance.
• Do not store flammable materials on or near the cooktop.
• Use only dry potholders; moist or damp potholders on hot
surfaces may cause burns from steam.
• Never leave the cooktop unattended when in use.
• Always position handles of utensils inward so they do not
extend over adjacent work areas, burners, or the edge of
the cooktop.
• Wear proper apparel. Loose fitting garments or hanging
sleeves should never be worn while cooking.
• Do not clean the cooktop while it is still hot. Some cleaners
produce noxious fumes when applied to a hot surface.
CAUTION
Do not allow pans to boil dry.
CAUTION
Do not store items of interest to children above the appliance.
If children should climb onto the appliance to reach these
items, they could be seriously injured.
IMPORTANT INSTRUCTION
Please read all instructions before using this appliance.

EN
4
2 - Rangetop Safety Instructions
Safety for the Cooktop
WARNING
Use Proper Pan Size
• This appliance is equipped with one or more surface units
of different size. Select utensils having flat bottoms large
enough to cover the surface unit heating element. The use
of undersized utensils will expose a portion of the heating
element to direct contact and may result in ignition of
clothing. Proper relationship of utensil to burner will also
improve efficiency.
Utensil Handles Should Be Turned Inward and Not
Extend Over Adjacent Surface Units
• To reduce the risk of burns, ignition of flammable materials,
and spillage due to unintentional contact with the utensil,
the handle of a utensil should be positioned so that it is
turned inward, and does not extend over adjacent surface
units.
• Do not place metallic objects such as knives, forks, spoons,
and lids on the cooktop surface since they can get hot.
Do Not Cook on Broken Cook-Top
• If cook-top should break, cleaning solutions and spillovers
may penetrate the broken cooktop and create a risk of
electric shock. Contact a qualified technician immediately.
Clean Cook-Top With Caution
• If a wet sponge or cloth is used to wipe spills on a hot
cooking area, be careful to avoid steam burn. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Warnings for Electric Installation
WARNING
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
CAUTION
• Always disconnect the electrical plug from the wall
receptacle before servicing this unit.
• For personal safety, this appliance must be properly
grounded.
• Do not under any circumstances cut or remove the third
(ground) prong from the power cord plug.

EN
5
3 - Features of your Oven
CONTENTS OF YOUR RANGETOP PACK 30’’
QTY DESCRIPTION QTY DESCRIPTION
1RANGETOP COOKER 2FIXING BRAKETS
1ISLAND TRIM
THREE FIXING SCREWS
MANUAL & GENERAL
DOCUMENTATION
1
“INSTALLATION INSTRUCTIONS”
1 “USE & CARE”
CONTENTS OF YOUR RANGETOP PACK 36’’
QTY DESCRIPTION QTY DESCRIPTION
1RANGETOP COOKER 2FIXING BRAKETS
1ISLAND TRIM
THREE FIXING SCREWS
MANUAL & GENERAL
DOCUMENTATION
1
“INSTALLATION INSTRUCTIONS”
1 “USE & CARE”

EN
6
4 - Features of your Cooktop
FEATURES OF YOUR COOKTOP 30’’
23
4
5
1
1 2 3 4
Position 1 2300W (Boost 3700W) 9” (230mm) induction element and control
Position 2 1400W (Boost 2200W) 6” ½ (165mm) induction element and control
Position 3 1850W (Boost 3000W) 7” ¾ (200mm) induction element and control
Position 4 1850W (Boost 3000W) 7” ¾ (200mm) induction element and control
Position 5 Led Display
DISPLAY UNIT INDICATIONS
A
B
C
NOTE: power levels are indicative and can vary according to the pan used or the settings made.
A - ON display
B - Power level display
C - Residual heat display

EN
7
FEATURES OF YOUR COOKTOP 36”
2
5b5a
3
6
74
1
1 2 3 4 5a 5b
Position 1 2300W (Boost 3700W) 9” (230mm) induction element and control
Position 2 1850W (Boost 3000W) 7” (180mm) induction element and control
Position 3 1850W (Boost 3000W) 7” (180mm) induction element and control
Position 4 2300W (Boost 3700W) 9” (230mm) induction element and control
Position 5a 3000W (Boost 5500W) 11” (280mm) induction element and control
Position 5b 1850W (Boost 2600W) 7” (180mm)
Position 6 Led Display
Position 7 Timer Display timer control
DISPLAY UNIT INDICATIONS
A
B
D
C
NOTE: power levels are indicative and can vary according to the pan used or the settings made.
A - ON display
B - Power level display
C - Residual heat display
D - Timer

EN
8
5 - Element and Control Setting
ELEMENT AND CONTROL SETTING
Control knobs and power level adjusting
The placement of each knob corresponds to the placement of the induction element that it controls.
To turn on any, PUSH and TURN the knob clockwise to the required setting, of the according cooking zone can be increased
between a minimum of 1 to a maximum of 9. To reduce the power of the cooking zone again it is necessary to turn the knob
anticlockwise.
The current power level is displayed on the display unit of the hob.
Melting function
If the knob is turned clockwise from zero position the first “power level” reached is the melting function.
The according 7 segment display unit shows this “u” symbol. The melting function is used to heat up
the bottom of the pot (40°C inside the pot). This function is used to melt food. The maximum time for
using the melting function is limited to 2 hours.
Warming function
The warming function is the second “power level” which will be selected when turning the knob
clockwise. The according 7 segment display unit shows this “U” symbol. The warming function is used
to heat up the bottom of the pot to 70°C (65°C inside the pot). Using this function the food can be kept
warm or it can be used to warm up food gently.
The maximum time for using the warming function is limited to 2 hours.
Automatic Heat Up time function
To activate the heat up time automatic press and turn the knob counterwise in overwind position “A”
until a beep sounds and the “A” symbol on the display starts blinking waiting for an input. Within the
next 10s a valid cooking level has to be selected from 1 to 8.
This will be the cooking level after a defined time of higher power output at level 9. The 7 segment
display alternates between “A” and the selected cooking level.
If the knob is turned clockwise by selecting level 0, level 9, (warming, melting) or in any position
counterwise the automatic heat up function will be turned off.
Booster function
To activate the boost function press and turn the knob clockwise in overwind position “P” until a beep
sounds. The symbol is as shown “P” and will be displayed. After 10 minutes the boost function will be
automatically switched off and the “P” is not shown on the display anymore and the induction control
will be set automatically at level 9.

EN
9
5 - Element and Control Setting
Cookware recognition function
The cooking level of cooking zone can be selected by turning the knob to the according position even
if no pot is in place. The output of power starts automatically as soon as an appropriate pot is put on
the cooking zone. If no pot is being detected the display changes to the shown “pot missing” symbol
after a short time. This symbol will be shown until a appropriate pot is put on the cooking zone or the
maximum time of 10 minutes expired. The same applies if the pot is removed during normal cooking.
After 10 minutes without detected pot the cooking zone switches off automatically and can only be
activated again after returning the knob into the OFF position.
Control Lock function
The control lock is a device that protects the appliance from accidental or inappropriate use. With all
cooking zones turned off, simultaneously press and turn the first two left knobs counterwise in overwind
position “A”. They need to be hold in that position for a least 2s until the symbols “L” appear on the
displays, then release the knobs.
In order to deactivate the CL function repeat the same procedure as for activating.
After unlocking all knobs have to be turned back in the zero position (if any knob was in a position
different from zero). The control is than off and can be operated as expected.
NOTE: If the knobs are not hold in the OWL position for long enough the CL will not be enabled /
displayed. If the knobs are hold in that position for more than 30 seconds the input is considered to be
invalid and a error message “Permanent use of key” will be displayed (flash symbol ).
Residual Heat indication
Cooking zones which are already switched off can still have a hot glass surface. In order to warn and
protect users from burning themselves this condition is visualized, the residual heat measurement is
done from the temperature sensor of each inductive cooking zone..
When the measured temperature drops below 60°C on the glass the symbol indicating the hot surface
disappears.

EN
10
6 - Advice on cooking
Some traditional methods of cooking, such as double boiler
(bain-marie) for creams, sauces, chocolate, etc. are no longer
necessary, because now you can cook these directly in the
pan, thanks to perfect power regulation and even temperature
distribution of the induction system.
You can use the “Booster” function with water and soups until
they boil, then use a lower level immediately to avoid too much
steam and to save energy.
When frying heat the oil to the highest power level, then turn
down if needed to a medium level when adding food to the
pan.
Always use pots and pans with a proper lid.
Reduce the selected power in the cooking area in time, in the
case of water do not let it boil unnecessarily for too long.
Always choose containers of an adequate size for the amount
of food to be cooked. A large pot which is not completely full
consumes a lot of energy.
For the best cooking results, metal pots and pans with a flat
bottom are recommended. Make sure the bottom of the pan
corresponds with the cooking area indicated on the glass.
To save energy cook vegetables and potatoes in a small
amount of water. Do not heat empty pans otherwise they may
be damaged and can also ruin the glass cooking area.

EN
11
7 - Induction Cooktop Operation
Before using the cooktop for the first time
• All products are wiped clean with solvents at the factory to
remove any visible signs of dirt, oil, and grease which may
have remained from the manufacturing process.
• Clean your glass top before the first time you use it. A
thorough cleaning with a glass top cleaner is recommended.
It only takes a minute and puts a clean, shiny coating on the
glass top before its initial use.
• There may be a slight odour during the first several uses: this
is normal and will disappear.
• Optimum cooking result depends on the proper cookware
being selected and used.
• The cooking surface will hold the heat and remain hot over
20 minutes after the elements have been turned off.
• The glass ceramic cooking surface is a durable material
resistant to impact but not unbreakable if a pan or other
object is dropped on it.
• Do nor allow pans to boil dry. This can damage the pan,
element and /or cooktop.
• Do not slide cookware across cooking surface it may scratch
the glass
• Using cast iron cookware on the glass cooktop Is not
recommended. Cast iron retains heat and may result in
cooktop damage.
Power Sharing
One generator controls 2 elements, or two/three cooking
zones within a heating section share the power of one
generator. Power Sharing is activated when both elements in
the same cooking zone are activated and one element is set for
Boost (P). The element that is not set for Boost will change to a
lower power level. This is called Power Sharing: The latest set
cooking level has priority.
30”
INDUCTION
36”
Power management (for 36” model only)
The 36” range features a power limitation system.
In the unusual case where 4 or 5 inductors of the cooktop are
being used on high (L9 or Boost) and the oven is then also
turned on, the power is reduced automatically on the cooktop
in order to keep the total consumption of the range below 50A.
However, it is unlikely that this level of power will be needed
during daily cooking activities and this power limiting event
may never be encountered. When the demand falls below 50A
again full power capabilities will be restored to the cooktop.
IMPORTANT
Automatic Switch OFF
The induction hob has an automatic device which limits the
duration of use.
Depending on the chosen cooking level a maximum
operation time limitation is defined, the safety device will be
activated only if no change of cooking level is done. If this
maximum operating time is exceeded on a cooking zone
this cooking zone is being switched off, a short beep sounds
and if the zone is hot the “residual heat” symbol is showed.
In order to reactivate this cooking zone the control knob has
to be turned back into OFF position.

EN
12
IMPORTANT
Overheating status of cooking zone
If the hob is used on full power for a long period, the
electronics could have trouble cooling down if the room
temperature is high. To avoid excessively high temperatures
forming in the electronics, the power to the cooking zone is
managed automatically to protect itself.
Permanent use of keys
FAULT MESSAGE
If the knobs have been kept rotated in the “A” or “P” positions
for more than 30 seconds a fault message will appear on the
display.
Cookware “noise”
When using adjacent elements that are set at certain power
level settings, magnetic fields may interact and produce a low
whistle or intermitted “hum”. Pans that completely cover the
element ring will produce less noise. A low “humming” noise
is normal particularly on high settings. These noise can be
reduced or eliminated by lowering or raising the power level
settings of one or both of the elements.

EN
13
8 - Cookware
How INDUCTION heating works
There is an electronic circuit inside the induction hob which
powers and commands a coil. This creates a magnetic field
which activates when it comes into contact with suitable pots
and pans (magnetic material).
The pan on the hob warms up instantly, while the hob remains
cold.
There is no loss of heat. The heat generated in the pan lets you
cook quickly, saving time and emergy.
Induction plate
Magnetic field
Pan heating
Pan in magnetic material
With pan the cooking
area is activated Without pan the cooking
area is not activated
Pots and pans and how to use them
ATTENTION
There is an electronic circuit inside the induction hob must
be made of ferromagnetic material. They can be made of
enamaled steel, cast iron or special pans of stainless steel
for induction.
To make sure a pan is suitable, try using a magnet to see
if it sticks to the bottom of the pan. Never use normal thin
steel nor anything containing even just an amount of glass,
terracotta, copper or aluminum.
The display of the cooking area will show if the pan is
suitable, if the power Indicator flashes the pan is not suitable
or the diameter of the bottom is too small for the diameter of
the cooking area.
The pots and pans must be placed precisely in the middle of
the cooking area.
In some cooking areas an internal diameter is indicated,
with a lighter outline.
COOKING AREAS 30”
INDUCTION
AB
BB

EN
14
COOKING AREAS 36”
C
B B
BB
D
Use the minimum size pan shown for each cooking element.
Diameter pan size
A3” 3/4 ( 9,5 cm) minimum diameter pan size
B5” 3/4 (14,5 cm) minimum diameter pan size
C4” 7/8 (12,5 cm) minimum diameter pan size
D9” 7/8 (25,0 cm) minimum diameter pan size

EN
15
9 - Cleaning the Cooktop
CAUTION
Be sure electrical power is off and all surfaces are cool
before cleaning any part of the cooktop.
Apply a small amount of cooktop cleaning specific ceramic
crème on a daily basis. this provides a protective film that
makes it easy to remove water spots or food spatters. The
temperature of the cooking surface reduces the protective
qualities of this cleaner.
It must be reapplied before each use. Use a clean cloth and
apply cooktop cleaning crème before each use to remove dust
or metal marks that can occur on the counter level surface
between uses.
FRAME
(Stainless steel models)
Always wipe with the grain when cleaning. For moderate/
heavy soil, use BonAmi® or Soft Scrub® (no bleach).
Wipe using a damp sponge or cloth, rinse and dry.
DAILY CLEANING TECHNIQUES
Clean the surface when it is completely cool with the following
exception.
CLEANING THE COOKTOP
Remove these soils immediately with the razor blade scraper:
• Dry Sugar
• Sugar Syrup
• Tomato Products
• Milk
USE DAILY
Wipe off spatters with a clean, damp cloth; use white vinegar
if smudge remains; rinse.
Apply a small amount of the Cooktop Cleaning Cream.
When dry, buff surface with a clean paper towel or cloth.
CAUTION
Do not use any kind of cleaner on the glass while the surface
is hot; use only the razor blade scraper. The resulting fumes
can be hazardous to your health.
Heating the cleaner can chemically attack and damage the
surface.
RECOMMENDED CLEANERS
• Cooktop Cleaning Crème:
Use only a small amount; apply to a clean paper towel or
cloth. Wipe on the surface and buff with a clean dry towel.
• BonAmi®:
Rinse and dry.
• Soft Scrub® (without bleach):
Rinse and dry.
• White Vinegar:
Rinse and dry.
• Razor blade scraper
Packaged with cooktop.
Note: The recommended cleaners indicate a type ofcleaner
and do not constitute an endorsement.
AVOID THESE CLEANERS
• Glass cleaners which contain ammoniac or chlorine bleach
These ingredients may permanently etch or stain the cooktop.
• Caustic Cleaners
Oven cleaners such as Easy Off® may etch the cooktop
surface.
• Abrasive Cleaners
Metal scouring pads and scrub sponges such as Scotch
Brite® can scratch and / or leave metal marks.
Soap-filled scouring pads such as SOS® can scratch the
surface.
• Powdery cleaners
Containing chlorine bleach can permanently stain the
cooktop.
• Flammable cleaners
Such as lighter fluid or WD-40.

EN
16
10 - Resolution of operational problems COOKTOP
Problem Cause Possible Remedy
Nothing works Cooktop not connected to proper
electricalcircuit.
Fuse is blown or circuit breaker is tripped.
No electricity to the cooktop.
Cooktop is in lockout mode.
Have electrician verify that the proper rated
cooktop voltage is being supplied to the
cooktop. Have electrician replace fuse or
reset circuit breaker.
Have electrician check your power supply.
Unlock cooktop.
Heating elements do not heat
properly Improper cookware is being used. Select proper cookware as outlined in the Cooktop Operation section of this manual.
Glass ceramic surface is
seethrough or appears to be red
in color.
Under direct or bright lighting, you will
sometimes be able to see through the glass
and into the chassis due to its transparent
quality. You may also notice a red tint under
these conditions.
These are normal properties of black ceramic
glass panels.
Lock Key blocked after first
connecting or unresponsive touch
control.
When first connecting electrically or after a
power failure, any direct strong light over
the sensor area may affect the touch control
functionality.
When powering on the unit make sure
that no strong light is shining direct over
the touch control zone, it can promise the
start-up sensor calibration resulting in an
unresponsive touch control.