REMOTE INTERFACE FOR
MICROSOL II PLUS AND MICROSOL II POWER
5 - FUNCTION MENU
(1)
The function menu allows configuring Microsol II controller functions remotely. To access the function
menu press and keys simultaneously for two seconds until the functions are shown in the
display. To access any function and confirm the value press ; to go back to the previous menu or to
leave any function without confirming press . The following options are available in the function
menu:
1- DESCRIPTION
Wall-Link is an interface intended to be used together with Microsol II plus from version 2 and
(1)
Microsol II power from version 1. It enables easy and quick remote access to all Microsol II
information and setup.
(1) Compatible with Microsol II plus or Microsol II power
2 - APPLICATION
Solar heating controlling.
3 - TECHNICAL SPECIFICATIONS
- Power supply: 90 - 264 Vac (50/60 Hz)
- Size: 90 x 131 x 28 mm (W x H x D)
- Operating temperature: 0 to 50°C
- Operating humidity: 10 to 90% RH (no condensation)
- Data communication: by wire - maximum distance of 1000 meters
4 - MAIN SCREEN
The figure below shows the main screen of Wall-Link with the system in operation.
01-Access Code
02-Functions
03-Schedule Mode
04-Schedule Evt
05-Clock
Preferential indication
description
Preferential indication
value
Swimming pool
26.9$C
5.1 - Access code
(1)
The access code 123 must be entered in this screen to enable changing functions of Microsol II
controller. To enter the code press on the message and adjust the value that will be blinking on the
display. Press again to confirm; to cancel and go back press .
5.2 - Functions
(1)
In this screen all functions of Microsol II can be adjusted. To make changes press on the desired
function and enter the value that will be blinking on the display. Press again to confirm the new
value; to cancel and go back press .
5.3 - Event scheduling mode
(1)
The operating mode of Microsol II event scheduling can be programmed from this screen.
5.4 - Event scheduling
The schedule of the instrument can be viewed and changed by accessing this function with the key .
To inform or change the configuration press on the option corresponding to the event and day of the
week. Adjust the time of beginning and end of the event using the and keys, press to
confirm the new value; to cancel and go back press .
To go back or to leave the options press at any time.
5.5 - Clock adjustment
(1)
To adjust the internal clock of Microsol II select this function by pressing . Then adjust the values
using the and and press to confirm or to cancel.
To go back or to leave the options press at any time.
6 - QUICK ACCESS MENU
The quick access menu allows configuring the setpoints of supports 1 and 2, as well as the manual
operating modes and the overheating temperature for sensor 2. To access this menu, press shortly
while Wall-Link main screen is displayed. To access any function and confirm the value press ; to
Function
description
Function code Function value
On Dif Temp
dOn@ 10.0 #
Function unit
Monday
E02@ 09:40/18:50
Day of week
Day event Start time Finish time
01-McSol 485 Add 02-Search McSol
go back to the previous menu or to leave any function without confirming press .
The following options are available in the function menu:
6.1- Auxiliary output 1 setpoint
This function allows adjusting the control temperature for auxiliary output 1.
6.2 - Auxiliary output 2 setpoint
This function allows adjusting the control temperature for auxiliary output 2.
6.3 - Sensor 2 overheating temperature
This function allows adjusting the overheating temperature for sensor 2. When applied to swimming
pools this is the limit temperature of the water (comfort temperature)
6.4 - Water pump operating mode
This function allows adjusting the manual operating mode of the water pump.
6.5 - Auxiliary output 1 manual mode enable
The operating mode of the auxiliary 1 output can be toggled between manual and automatic by
pressing on this function.
6.6 - Auxiliary output 2 manual mode enable
The operating mode of the auxiliary 2 output can be toggled between manual and automatic by
pressing on this function. Note: This option will be only available for Microsol II plus from version
03 or Microsol II power from version 01.
6.7 - Viewing the minimum and maximum temperatures
(only available for Microsol II power)
Pressing the key in this function you can browse the minimum and maximum temperatures for
each sensor of Microsol II Power.
7 - ACCESS MENU FOR ADJUSTING THE CONNECTION
(1)
Upon accessing the quick access menu while Wall-Link is not connected to Microsol II , the user will
have two functions available for adjusting the address of the instrumet :
(1)
7.1 - McSol 485 Add (Microsol II address)
(1)
The address of Microsol II controller can be manually adjusted by entering this function. The value of
(1)
this function must be the same value configured in Microsol II .
(1)
7.2 - Search McSol (Search Microsol II )
(1)
Pressing on this function makes Wall-Link start searching for Microsol II address automatically.
Enter the quick access menu again to stop the automatic search.
8 - SETUP MENU
The operating characteristics of Wall-Link can be adjusted through the setup menu. To access the
function menu press and keys simultaneously for eight seconds until the functions are shown
in the display. The following options are available in the setup menu:
(1)
8.1 - McSol2 485 Add (Search Microsol II )
(1)
This function allows to manually adjusting the address of the Microsol II controller.
(1)
The value set for this function should be the same value set on the Microsol II .
8.2 - Interface
Allows adjusting the user interface characteristics:
01-McSol 485 Add 04-Timeouts
02-Interface
03-Descriptions
05-Statistics
Fun
S1
-
1
0
Off
All
-
10
999
On
-
-
-
min.
-
Indication
Language (Port, Engl, Esp)
Display contrast
Display timeout
Sound signaling
S2
Port
5
0
Off
I01
I02
I03
I04
I05
01-Setpoint A1
03-S2 Hi Temp
05-A1 Man Mode
04-Pmp Activat
02-Setpoint A2
06-A2 Man Mode
07- Min max Temp
Description Max. Unit
Min.
Default
Ver.04
WALLLINK04-01T-12617
Only with Microsol II plus version 03 or
Only with Microsol II power version 01
higher
