Fumagalli Pliko User manual

User’s manual
PLIKO
Children rehabilitative stroller
Version 06.14

Maintenance
Removable and washable cover up to 30°.
Keep the movement parts clean and greased using a light oil.
Dry the metal parts in order to avoid rust.
Periodically clean the plastic parts with a moist cloth: do not use solvents or other similar products.
Brush the dust off from textile parts.
Keep the wheels clean from dust and sand.
Protect the product from adverse weather conditions (rain or snow) –continuous exposure to
sunlight could cause some of the materials to change colour.
Warning!
Do not use chlorine-based detergents.
Safety:
1. Never leave your child unattended.
2. Avoid putting fingers into the blocking parts.
3. Unfolding of the buggy should only be carried out by an adult.
4. Do not use the buggy if parts are missing or broken.
5. Always use the brake when the buggy is still.
6. Do not use the buggy near stairs or steps.
7. Do not lift the buggy by its front bar as it is not designed to withstand this. If you need to lift
the buggy, lift it from under the armrests or by the frame
8. Ensure that the buggy is correctly opened and blocked: the red signs under the block levers
should not be visible.

Technical parameters
Weight
10 kg
Width
42 cm
Seat depth (PS)
24 –30 cm
Seat width (LS)
25 ÷ 34 cm
Backrest height (AS)
63 cm
Backrest width
34 cm
Footrest length
6 ÷ 30
Maximum width (L)
54 cm
Depth (P)
99 cm
Height (A)
102 cm
Dimensions when folded (width x height x
length)
36x41x119 cm
Reclinable angle
800
Maximum load weight
20 kg (+ 5 kg basket)
PLIKO opening
Pull up the two handle levers and at the same time
lift the buggy which will then unfold itself
automatically. Check the two side hooks to verify
that the buggy is completely open.
After unfolding, position the footrest platform and
the lateral padded cushions if they have unhooked
during transportation.
Side hooks

Pliko closing
To close the buggy, remove the footrest platform by pulling its blocking cable downwards; then pull
up the two levers on the push-handles so that the hooks are also released. Hold the back-handle (3)
and pull it up: the buggy will fold itself automatically. Now the buggy can be pulled along on its
wheels or carried by its handle.
Adjustments
Adjustment of handles.
The handles are individually adjustable at two different heights;
press the block button and raise or lower the handle.
Front bar
Fit or remove the front-bar as shown.
Brakes and castors
The rear wheels have a parking brake system. It is also possible to block the pirouetting movement of
the front wheels using the block system.
Blocking cable of
the the footrest
platform

Hood assembly
Insert the hood into the side supports and
push downwards until it “clicks”, as shown;
button the hood to the buggy frame and
push down on the compass hinge to
tighten it.
Backrest inclination
The backrest can be adjusted to four
different positions. To lower it, pull up the
handle B and at the same time lower the
backrest to the required position and block
it. To raise, push the backrest upwards.
Seat depth and width adjustment
The seat depth can be adjusted by loosening
the two bolts positioned on the side runners
under the seat and adjusting the seat by
following the sliding mechanism.
The lateral cushions have a zip in order that
extra pads can be inserted so that the
seatwidth can be narrowed
Warning: if extra pads have been added,
when folding the lateral cushions must be
moved to the outside of the Pliko buggy.
Headrest and pelvis supports
The headrest is adjustable at different heights through the holes in the backrest covering.
The pelvis support can be removed if not necessary or be fitted at the required height using the slots
in the covering.
Lateral cushions
Blocking bolt position of the seat
sliding mechanism

Foot platform adjustment
The foot platform is height adjustable by loosening the blocking bolts and the tilting adjustment is
made by screwing or unscrewing the bolt under the platform itself. The platform has two width
adjustable footrests.
Belts
The belts with sliding pads can be fixed at the appropriate height simply by inserting them into the
right slot of the backrest covering.
To fix the pelvic belt, use the fixing slots on the back of the seat.
Pads and postural systems
The seat, backrest, lateral cushions and pelvic support are made so that it is possible to add pads as
necessary to suit the child’s postural needs.
All covers are removable and washable, as per the label instructions.
The seat cushion has a Velcro closing system that allows for the raising of the front part if
required.
All postural adjustments are to be carried out by
specialised personnel, after the evaluation of each single
child.
Storage basket
The storage basket must be fixed using the proper
hooks (AB-C) as shown in the picture.
Warning!
ALWAYS REMOVE THE FOOTREST BEFORE FOLDING
Non-removal of the footrest before folding may cause serious, irreparable structural
damage. Fumagalli therefore accepts no responsibility for any damage arising from failure to comply
with the instructions written in the user manual.

Manufacturer:
Fumagalli srl
Piazza Puecher 2
22037 Ponte Lambro (Co)
Tel.: [phone]
Fax: [phone]
www.fumagalli.org
Distributor:
mdh sp. z o.o.
ul. Tymienieckiego 22/24
90-349 Lodz
Tel.: [phone]
Fax: [phone]
www.mdh.pl
www.viteacare.com