Furngully SPROUT PRO BP-2 User manual

SPROUTPRO
SIDE-BY-SIDE INSTALLATION GUIDE
BP–2
*General Guide| See MasterPlan

48" POWER
PARTS LIST
ITEM
CODE QTY PRODUCT CODE
BPROTPB 1 Module Mounting Plate (Short)
BPROTPB 2 Power Module Bracket
PRODB 1 Double Receptacle Block
PROR 4 Receptacles
1

Slide inner beam inside of the outer beam and adjust until at least 2
power slots are visible on the inner beam.
Place receptacle on top of mounting plate. Slide brackets over
receptacle and secure with provided screws.
1| ATTACH RECEPTACLE TO MOUNTING PLATE
2 | ASSEMBLE POWER BEAM
POWER
SPROUTPRO
Note: Do not over torque screws
Outer Beam
Inner Beam
2

POWER
SPROUTPRO
3 | CONNECT JUMPER TO RECEPTACLE
Before securing to power beam, secure jumper(s) to receptacle.
4| INSERT POWER INTO BEAM
Insert the modules into the slot in the power beam. One end will
connect to the inner beam and the other end will connect to the
outer beam.
Connect to
Inner Beam
Connect to
Outer Beam
3

PARTS LIST 54"-72"
54"-72" POWER
ITEM
CODE QTY PRODUCT CODE
BPROTPB 1 Module Mounting Plate (Long)
BPROTPB 3 Power Module Bracket
PRODB 1 Double Receptacle Block
PROSB 1 Single Receptacle Block
PROBC 1 In-line Connector
PROR 6 Receptacles

POWER
SPROUTPRO
2 | ASSEMBLE POWER BEAM
Slide inner beam inside of the outer beam and adjust until at least 2
power slots are visible on the inner beam.
Place receptacle on top of mounting plate. Slide brackets over
receptacle and secure with provided screws.
1| ATTACH RECEPTACLE TO MOUNTING PLATE
Note: Do not over torque screws
Outer Beam
Inner Beam

Insert the modules into the slot in the power beam. One end will
connect to the inner beam and the other end will connect to the
outer beam.
Before securing to power beam, secure jumper(s) to receptacle.
3 | CONNECT JUMPER TO RECEPTACLE
4| INSERT POWER INTO BEAM
POWER
SPROUTPRO
Note: Jumper connects to the single block
6

ITEM
CODE QTY PRODUCT CODE
BPROF 2 LEG
2 Surface Attachment Bracket
2 Surface Support Bracket
1 Width Adjusting Bracket
BPRO24F 2 24" Feet
BPROSRB 2 SR Beam Mounting Bracket
BPROTPB 1 Power Beam
BPROTPB 1 Data Beam Set
1 Laminate Surfaces
Note: Parts list is for a single workstation, additional parts will be
needed for additional workstations
SPROUTPRO
PARTS LIST
7

Set frame assembly upside down on floor and then place legs
inside of frame aligning the second hole of the frame with the front
of the foot.
1| SECURE LEGS TO FRAME
Note: Be sure welded brackets are facing back of workstation
2 | CONNECT SURFACE BRACKETS
Slide bracket under frame, align pre-drilled holes of surface
bracket to SproutPro frame and secure with 4 screws each.
Note: Longer side of bracket should face front of workstation
SINGLE RUN
SPROUTPRO
Front
Back
1

Note: If you are adding an end panel, measure to 2" from rear of
surface on 30" work surfaces
3 | SET FRAME ON SURFACE AND SET LENGTH
Measure from outer edges of workstation legs to determine proper
workstation length. Use the chart below to determine the length of
workstation frame.
4| ALIGN FRAME WITH SURFACE WIDTH
Measure from outer edges of workstation legs to determine proper
workstation length. Use the chart below to determine the length of
workstation frame.
Surface
Width
Frame
Length (#)
48" 47.5"
54" 54"
60" 60"
66" 66"
72" 66"
SINGLE RUN
SPROUTPRO
#"
2”4”
24" Surface 30" Surface
2

Using wood screws, attach frame to surface and tighten screws on
adjustable center bracket.
5 | SECURE FRAME TO SURFACE
Note: You may need a right angle drill attachment
Slide the beam mount over the welded bracket on back of leg with
4 screws. Be sure the smaller cutout on the mount is facing inward.
6 | ATTACH POWER BEAM MOUNT
SINGLE RUN
SPROUTPRO
Adjustable
Bracket
3

7 | SECURE POWER BEAM TO WORKSTATION
Use a 6" extension to secure power beam end to center cutout of
SR Beam Mounting Bracket with 4 screws on each end.
8 | SET POWER BEAM WIDTH
Using the set screws, interconnect the inner and outer power beam
sections for additional stability.
Note: Use 2 screws with 48" with workstations and 4 screws for all
other widths
SINGLE RUN
SPROUTPRO
4

SINGLE RUN
SPROUTPRO
Slide the inner beam into the grooves of the outer bream and place
onto the underside of the power beam and adjust width as needed
and secure.
After power beam is secured, remove data plate from the outer
beam.
9 | ASSEMBLE DATA TRAY
9 | REMOVE DATA PLATE
5

10 | REMOVE GLIDE AND INNER BRACKET
11 | (OPTIONAL) SLIDE ON PANEL BRACKETS
SINGLE RUN
SPROUTPRO
Twist off glides, then using an allen wrench remove the 2 holding in
the glide bracket.
If you have laminate panels, slide brackets over legs. Tabs on
brackets must face the direction that panels are being added.
Note: Glides must be removed so feet can be added to workstation
Note: Brackets must be added before feet are attached.
6

12 | SECURE FEET TO LEGS
13 | SECURE AND CONNECT CONTROL BOX
Using 4 screws for each foot, secure to legs with longer side of foot
facing the front of the workstation.
Place control box inside of the center beam and secure with 2
wood screws. Connect the leg wires to the control box.
SINGLE RUN
SPROUTPRO
7

Connect handset cable to control box. Align front of handset with
surface edge and secure with 3 wood screws.
14 | SECURE HANDSET AND CONNECT
15 | FLIP WORKSTATION AND INITIALIZE
Connect cord to power source then press and hold and
simultaneously for 5 seconds until both leg columns are in lowest
position. Desk will slightly rise, lower again, and then stop. Release
buttons. The system is now operational.
SINGLE RUN
SPROUTPRO
8

SINGLE RUN
SPROUTPRO
16 | ALIGN AND CONNECT WORKSTATIONS
Pass jumper through bridge extension then insert the extension
into the open slot of power bridge on first workstation. Align
second workstation, connect jumper and push workstations
together. Both ends of bridge extension should site inside of power
bridge.
Use BPROBRG2 (12.25")extension for workstation have 72" surfaces.
Use BPROBRG1 (7.5") extension for workstation of any other size.
Note: Repeat for all side-by-side workstations
Note: Width between workstations will vary depends on extension
9

© 2021 Furngully. All rights reserved.