Furuno MCU-004 User manual


Included items
Outline and dimensions
How to install the Remote Control Unit
1. Table shown below indicates tolerance of
dimensions which are not specified.
2. "#" indicates minimum service clearance.
3. Use self-tapping screws (ø4×16, included)
to secure the unit.
DIMENSIONS (mm)
0 < L ≤ 50
50 < L ≤ 100
100 < L ≤ 500
TOLERANCE (mm)
±1.5
±2.5
±3
Using the mounting template on the left, cut a mounting
hole in the installation site.
Set the unit to the hole and secure the unit with four
self-tapping screws (ø4×16, supplied).
Name
Remote Control Unit
Type
MCU-004
Qty
1
4
Self-tapping Screw 4
× 16 SUS 304
Control description
STBY•AUTO key
Switches the steering mode of the FURUNO NAVpilot-700
series Autopilot between the STBY and AUTO modes.
Joystick
Push: Works same as the tap gesture.
· Opens the pop-up menu.
· Activates the selected item.
Operate the joystick:
in Cursor mode
· Moves the cursor.
in Scroll mode
· Pans the display (Plotter/Weather/Radar display).
· Shifts the range and scrolls back the picture (Fish finder display).
FUNC key
Activates the function set at [Function Gesture] in the [General]
menu.
HOME/BRILL key
Short press:
· Opens the home screen.
Long press:
· Opens the Brilliance/Power window.
Self-tapping
screw (4 pcs)
Remote control unit
Attach four screw caps (supplied).
-
000-162-605-10
Code No.
Procedure
Screw cap
(4 pcs)
77 mm
175 mm
26 mm 54 mm #38 mm
7.5 mm
USB cable
(3 m)
Mass* 0.4 kg ± 10 %
Ambient temperature -15 °C to +55 °C
Relative humidity
Degree of protection
93 % or less at 40 °C
IP56 (front), IP22 (back)
Remote Control Unit MCU-004
*: Mass includes the hard cover and USB cable.
Specifications
Notes
7
8
CONTROL key
Switches between displays that can be controlled with the
MCU-004 when multiple displays are installed in the same
network.
CURS•SCRL key
Switches the function of the joystick between the Cursor and
Scroll modes.
CENTER key
· Returns your ship to the center of the screen (Plotter/
Weather/Radar display).
· Cancels the echo history (Fish finder display).
EDGE key
TZT9/TZT14/TZTBB operation
Opens the RotoKeyTM menu.
TZTL12F/TZTL15F operation
Press the EDGE key and operate the joystick to activate the Edge
Swipe function: Quick page, Slide-out menu, [Layers] menu, and Data
area.
· Opens the [Layers] menu. · Opens the Quick page.
· Opens the Slide-out menu. · Opens the Data area.
CANCEL/MOB key
Short press:
· Moves to the previous page or layer in a menu.
· Closes the menu or dialog box.
· Ends the tool mode (End Route, End Move, etc.).
Long press:
· Enters the MOB mark at the own ship’s position.
· Selects an item from the menu and dialog box.
· Zooms in (+) and out (-).
Rotary knob
4
1
Screw Cap 19-032-3508-3 100-404-903-10
Hard Cover 19-032-3509-3 100-404-913-10
• For TZT9/TZT14/TZTBB, the cross cursor is easier to use than the arrow cursor. To use the cross cursor, set [Cross
Cursor] to [ON] in the [General] menu.
• The MCU-004 is compatible with the FURUNO Multi Function Displays and software version combinations shown below.
TZT9, TZT14, and TZTBB: Version 5.01 or later (Planned release: Beginning of 2017)
TZTL12F and TZTL15F: Version 3.01 or later (Planned release: Middle of 2016)
Tips and NoticeTips and Notice
Power supply
USB bus power (Consumption
current: Max. 270 mA)
Connect the USB connector of the unit to the USB port of either
the NavNet TZtouch or TZtouch2.
thenthen thenthen
thenthen thenthen
HOME
BRILL
STBY
•
AUTO
FUNC
1 2
43
CURS
•
SCRL CENTER
56
9
CANCEL
MOB
10
Note 1: When using a USB hub to connect this device, keep in mind that the maximum power consumption for this
device is 270 mA.
Note 2: When you extend the USB cable by 5 m or more, a USB hub or USB repeater cable is required.
REMOTE CONTROL UNIT Model MCU-004
User's Guide
The purpose of this guide is to provide the basic operation and
installation of the Remote Control Unit MCU-004.
All brand and product names are trademarks, registered
trademarks or service marks of their respective holders.
Note: This template may have expanded or shrunk
slightly. Please confirm dimensions before use.
Drill hole for ø4×16 self-tapping screw (four places).
Drill hole of 35 mm in dia (four places).
64±1 mm (2.50")
162±1 mm (6.38")
31 mm
(1.22")
129 mm (5.08")
164 mm (6.46")
66 mm
(2.60")
Pub. No. E42-01509-A2
(1611, REFU) MCU-004
00019129110

(Back of the mounting template)
Zoom in and out
Rotate the rotary knob to zoom in or out the chart scale (Plotter/Weather display) and select the range (Radar/Fish finder display).Rotate the rotary knob to zoom in or out the chart scale (Plotter/Weather display) and select the range (Radar/Fish finder display).
How to inscribe/go to a point
Zoom in
Home screen operation
Press the HOME/BRILL key to open the home screen. The home screen is
where you access functions and menus, select displays and check sensor status.
Press the HOME/BRILL key to open the home screen. The home screen is
where you access functions and menus, select displays and check sensor status.
Zoom in Zoom out
Display selection
Rotate the rotary knob to put the orange
frame on the applicable display icon.
Rotate the rotary knob to put the orange
frame on the applicable display icon.
Push the joystick to open the selected
display.
Push the joystick to open the selected
display.
Menu operation
Rotate the rotary knob to put the orange frame on the applicable menu item.Rotate the rotary knob to put the orange frame on the applicable menu item.
Rotate the rotary knob in clockwise direction.Rotate the rotary knob in clockwise direction. Rotate the rotary knob in counterclockwise direction.Rotate the rotary knob in counterclockwise direction.
Edge Swipe function (TZTL12F/TZTL15F only)
Press the EDGE key and operate the joystick to activate the Edge Swipe function: Quick page, Slide-out menu, [Layers]
menu, and Data area.
Press the EDGE key and operate the joystick to activate the Edge Swipe function: Quick page, Slide-out menu, [Layers]
menu, and Data area.
Cursor and Scroll modes
Press the CURS•SCRL key to switch the function of the joystick between the Cursor and Scroll modes.Press the CURS•SCRL key to switch the function of the joystick between the Cursor and Scroll modes.
[Layers] menu
[Layers] menu
Data area Quick page Slide-out menu
Cursor mode operation Scroll mode operation
In the cursor mode,
the cursor appears on
the display other than
the home screen and
menu. Operate the
joystick to move the
cursor.
In the cursor mode,
the cursor appears on
the display other than
the home screen and
menu. Operate the
joystick to move the
cursor.
In the scroll mode, you
can pan the display
(Plotter/Weather/Radar
display), shift the range
and scroll back the
picture (Fish finder
display) with the
joystick.
In the scroll mode, you
can pan the display
(Plotter/Weather/Radar
display), shift the range
and scroll back the
picture (Fish finder
display) with the
joystick.
Cursor
Data
area
雨雪反射
0
10
20
30
40
50
60
70
80
90
100
110
120
200
230
240
250 260 270
280
290
300
310
320
330
340
350
210
180
170
160
140
220
190
150
130
340
TX
RADAR
DATA ROUTE
Radar Control
2:01 PM
Data
area
6,695
Quick page
Side-out
menu
Switching displays and selecting an active window
TipsTips
Note: The instructions and screenshots below are based the TZTL12F/TZTL15F.Note: The instructions and screenshots below are based the TZTL12F/TZTL15F.
How to inscribe a point
Move the cursor on the
position to inscribe a point,
then push the joystick.
Move the cursor on the
position to inscribe a point,
then push the joystick.
Select [New Point].Select [New Point].
Cape Florida Light
fl1w 6s28m
Lat
Lon
N 25°39.958'
N 80°09.352'
Range
Bearing
13.00 NM
256.4°R
New Point
Goto
New Route
Tide
How to go to a point
Move the cursor on the
point or position to set as
a temporary destination,
then push the joystick.
Move the cursor on the
point or position to set as
a temporary destination,
then push the joystick.
Select [Goto].Select [Goto].
Cape Florida Light
fl1w 6s28m
Lat
Lon
N 25°39.958'
N 80°09.352'
Range
Bearing
13.00 NM
256.4°R
Goto
Move
New Route
Name
Push to Enter.
Push to Enter.
• In the cursor mode, you can pan the display by moving the cursor to the edge of the screen. This function is available in the full screen
Plotter/Weather/Radar display.
• You can adjust the cursor speed on the [General] menu.
Selecting an active window
To select an active
window in a split
display, move the
cursor on the
applicable window.
An orange frame
appears around
the current active
window.
To select an active
window in a split
display, move the
cursor on the
applicable window.
An orange frame
appears around
the current active
window.
Switching displays
When multiple displays are installed in the same network, press the
CONTROL key to switch between displays that can be controlled
with the MCU-004.
When multiple displays are installed in the same network, press the
CONTROL key to switch between displays that can be controlled
with the MCU-004.
Lat
Lon
N 25°39.958'
N 80°09.352'
Range
Bearing
13.00 NM
256.4°R
New Point
Goto
New Route
Tide
Chart Info
Move Boat
Push the joystick to
activate the selected item.
Push the joystick to
activate the selected item.
How to inscribe an event mark
Push to Enter.
Push to Enter.
Push to Enter.
Push to Enter.
Push to Enter.
Push to Enter.
Select [Event].Select [Event].
Select a mark.Select a mark.
Open the Slide-out menu.Open the Slide-out menu.
thenthen thenthen thenthen thenthen
Home screen
Push the joystick to
inscribe the selected
mark at the own ship
position.
Push the joystick to
inscribe the selected
mark at the own ship
position.
thenthen
Zoom out