Furuno MCU-002 User manual

REMOTE CONTROL UNIT Model MCU-002
User's Guide
The purpose of this guide is to provide the basic operation and
installation of the Remote Control Unit MCU-002.
All brand and product names are trademarks, registered
trademarks or service marks of their respective holders.
Note: This template may have expanded or
shrunk slightly. Please confirm
dimensions before use.
Packing List
Outline and dimensions
How to install the Remote Control Unit
59
Note:
1. Table1 indicates tolerance of dimensions
which is not specified.
2. #: Minimum service clearance.
Table 1
DIMENSIONS (mm)
0 < L ≤ 50
50 < L ≤ 100
100 < L ≤ 500
TOLERANCE (mm)
±1.5
±2.5
±3
Using the mounting template, open a mounting hole in the
installation site.
Fix the unit with four flush mount screws (Ø3x13), then attach
the front panel.
Connect the USB connector of the unit to the USB port.
19 35.5 #38
4
1.5 10
Gasket
Name
Remote Control Unit
Type
MCU-002
FRC-D01-008
SUS304 BH T/S-1
Qty
Flush Mount Gasket
Flush Mount Screw
1
1
4
Mounting
hole
(MASS: 0.14 ± 10 % kg)
115
102±0.5
34±0.5 Fixing holes
Installation
1 Front Panel FRC-D01-003
If it is necessary to remove the front
panel after the unit is installed, insert a
slotted head screwdriver into the slot
on the unit, then turn the screwdriver.
Control description
Controls
· In the cursor mode of the MCU-002, the cross cursor is easier to use than the arrow cursor. To use the cross cursor, set [Cross Cursor] to [ON] in
the [General] menu.
· You can not set the guard zone with the MCU-002. Use the touch operation to set the guard zone.
m
NavData Transparency
D
ept
h
Al
arm
V
a
l
ue
S
ea
S
ur
f
ace Temperature Alar
m
T
emperature
Al
arm
V
a
l
ue
Temperature Alarm Ran
g
e Minimum Valu
e
Temperature Alarm Ran
g
e Maximum Value
Off
30.0
f
t
7
0.0
°
F
60
.
0
°
F
7
0.0
°
F
Synchronize Time with GPS
Cross Cursor
Set [Cross Cursor] to [ON] .
Cross Cursor
Tips and NoticeTips and Notice
· Selects an item from the RotoKeyTM/main/pop-up menu
and dialog box.
· Zooms in (+) and out (-).
· Raises (+) and lowers (-) the brilliance on the
Brilliance/Power window.
Flush mount
screw
Front panel
Set the flush mount gasket and unit to the hole.
Flush mount gasket
STBY•AUTO key
Switches the steering mode of the FURUNO NAVpilot-700
series Autopilot between the STBY and AUTO modes.
CENTER key
· Returns your ship to the center of the screen
(Plotter/Weather/Radar display).
· Cancels the echo history (Fish finder display).
CURS•SCRL key
Switches the joystick gesture between the cursor mode
and scroll mode.
Joystick
Short push: Works same as the tap gesture.
· Opens the pop-up menu.
· Activates the item selected by the cursor.
Long push: Works same as the long press gesture.
· Opens the detail pop-up menu.
Operate the joystick:
Cursor mode operation
· Moves the cursor.
Scroll mode operation
· Pans the display (Plotter/Weather/Radar display) .
· Shifts the range and scrolls back the picture (Fish finder display) .
FUNC key
Activates the function set at [Function
Gesture] menu.
HOME/BRILL key
Short press:
· Opens the home screen.
Long press:
· Opens the Brilliance/Power window.
ENT key
· Activates a selected item.
· Opens the RotoKeyTM menu.
CANCEL/MOB key
Short press:
· Closes the menu or dialog box.
· Stops the audio alarm.
· Ends the tool mode
(End Route, End Move, etc.).
Long press:
· Enters the MOB mark at the
own ship’s position.
+, - key
Event
Lat/Lon
Track Rec.
◄ Orientation
3D
R3
Pilot holes (four places)
34±0.5 mm (1.34")
49.6±0.5 mm (1.95")
91±0.5 mm (3.58")
102±0.5 mm (4.02")
SD-Left
Cancel
Screen Capture
SD-Right
Go To
New Point
New Route
More...
N 26°27.027'; W 80°56.264'
53.97 NM / 230.6°

Display selection
HOME
BRILL ENT
Select a display.Select a display.
RotoKeyTM menu operation
ENT
Lat/Lon
3D
Event
Track Rec.
◄ Chart
Select an item.Select an item.
ENT
Activate the selected item.Activate the selected item.
Go To
New Point
New Route
More...
N 26°27.027'; W 80°56.264'
53.97 NM / 230.6°
Pop-up menu operation
Select an item.Select an item.
ENT
Activate the selected item.Activate the selected item.
Main menu operation
HOME
BRILL
Select the [Menu] icon
with the cursor.
Select the [Menu] icon
with the cursor.
Select a main menu item.Select a main menu item. Select a sub menu item
with the cursor.
Select a sub menu item
with the cursor.
Activate the selected item.Activate the selected item.
Open the home screen.Open the home screen.
How to operate the menus
Open the home screen.Open the home screen.
Open the RotoKeyTM menu.Open the RotoKeyTM menu.
The pop-up menu appears.The pop-up menu appears.
Push the joystick.Push the joystick.
Push the joystick.Push the joystick.
Open the selected display.Open the selected display.
Basic operation
Zoom in and out
Zoom in Zoom out
The +, - keys zoom in or out the chart scale (Plotter/Weather display) and select
the range (Radar/Fish finder display).
The +, - keys zoom in or out the chart scale (Plotter/Weather display) and select
the range (Radar/Fish finder display).
Scroll mode operation
You can pan the display (Plotter/Weather/Radar display), shift the range and scroll back the
picture (Fish finder display) with the joystick. To switch to the scroll mode, press the CURS•SCRL
key. In the scroll mode, the cursor disappears.
You can pan the display (Plotter/Weather/Radar display), shift the range and scroll back the
picture (Fish finder display) with the joystick. To switch to the scroll mode, press the CURS•SCRL
key. In the scroll mode, the cursor disappears.
CURS
SCRL
•
Switch to the scroll mode.Switch to the scroll mode.
Operate the joystick.Operate the joystick.
CENTER
Center Vessel
Center Radar
Cancel Hist.
How to put a point, How to go to a point How to put an event mark
How to put a point
Select the position to set
as a point.
Go To
New Point
New Route
More...
N 26°27.027'; W 80°56.264'
53.97 NM / 230.6°
The point is put
on the screen.
[New Point] is selected.
How to go to a point
Select the point or position
to set as a point to go.
Go To
New Point
New Route
More...
N 26°27.027'; W 80°56.264'
53.97 NM / 230.6°
Select [Go To].
ENT
Event
Lat/Lon
Track Rec.
◄ Orientation
3D
Select [Event].Select [Event].
Cancel
Creating Event
Select an event mark. The selected event mark
is put on the screen.
30
40
50
60
70
80
90
100
110
120
130
140
150
210
220
230
240
250
260
270
280
290
300
310
320
330
Note: In the cursor mode, you can pan the display by moving the cursor to the edge of the screen.
This function is available in the full screen Plotter/Weather/Radar display.
Note: In the cursor mode, you can pan the display by moving the cursor to the edge of the screen.
This function is available in the full screen Plotter/Weather/Radar display.
Push the joystick.Push the joystick.
Push the joystick.Push the joystick.
or
ENT
ENT
Open the RotoKeyTM menu.Open the RotoKeyTM menu.
or
Activate [Go To].
ENT
Start to go to a point.
The pop-up menu appears.The pop-up menu appears.
The pop-up menu appears.The pop-up menu appears.
Yes No
Do you want to navigate using the NAVpilot?
Select [Yes] or [No] in
the dialog box*.
Select [Yes] or [No] in
the dialog box*.
ENT
Activate [Event].Activate [Event].
ENT
Zoom in Zoom out
*: Appears when the NAVpilot-700 series Autopilot is installed in the TZT network.*: Appears when the NAVpilot-700 series Autopilot is installed in the TZT network.
00017941910
PUB. NO. E42-01403-A1
(1405, REFU) MCU-002
Push the joystick.Push the joystick.