Fusion MS-EL602 Guide

•••••
••••••••••
•••••••••••••••
~ ················
wr- •••••••••••••••••••
••••••••••••••••••••
•••••••••••••••••••••••
••••••••••••••••••••••••
•••••••••••••••••••••••••
•••••••••••••••••••••••
························~~~
-~~~~~·····················
~~~~~~~~~\\\\\\\~~'-'-\'-'-'-'-~\·
\~\\\\\\\\\\~i\\\\\~~·
••\\\\\\\\\\••\\~~~~··
\\\\\\~\\~·~~~~~··
········\~···
"Hsu

2

CONTENTS
• CONTENTS .....................................••....•................................................... pg 3
•
CONTENTS OF BOX ....•...........••................................................................. pg 4
•
PRODUCT SPECIFICATIONS .................•........•........................................•. pg 4
• LINE
DRAWINGS & DIMENSIONS ......................••........•............................... pg 5
• INSTALLATI0N GUIDE..........•........•...•..•.......•..................................•........pg 6
• INSTALLATI0N TIPS..•...........•....•......•..•.•....•.•••........................•...............pg 7
•
TROUBLESHOOTING ................•................................................................ pg 7
REGISTER YOUR PRODUCT ONLINE
For your own peace of mind, register your product purchase online at
www.fusionelectronics.com
We'll keep you up to date with any news related to your product or new
accessories to help you get the most from your product.
RECORD YOUR PRODUCT DETAILS HERE:
SERIAL NUMBER
DATE OF PURCHASE
AFFIX RECEIPT HERE
3

FUSION
Marine
speakers
have been
thoroughly
tested to
ensure
consistent
and
reliable
performance.
The
shallow
mount
design of
the
MS-EL602
speakers
ensure
simple
installation,
the
sleek
and styled
grille
design is a
complement
to
any vessel
while
maintaining
environmental
protection
and sound
quality
as
the
core focus.
LIST
OF
CONTENTS
• 2 x
Speakers
• 2 x Tinned
Speaker
Wire
• 8 x
Stainless
Steel
Mounting
Screws
• 1 x
Mounting
Template
• 2 x
Mounting
Gaskets
•
User
Manual
•
Warranty
Card
Peak Power: 150
Watts
Woofer
Size: 6"
Cone
Material:
Polypropylene
Tweeter
Type: PEl
Efficiency [1
WI
1
M
)
: 85 dB
Frequency Response: 60Hz -22kHz
Impedance: 4 Ohm
Min
Mounting
Depth
Clearance:
41mm
(1-5/8")
Mounting
Diameter:
130mm
[5-1/8")
4

LINE
DRAWINGS
&
DIMENSIONS
B.
~
I'-.)
3
3
l.f1
............
w
N
t---------12
7mm
[5"]
------------1
~------------
~
177mm[
6-31/32"]
--------------t
w
............
w
N
I'-.)
V1
3
3
N
--..1
............
w
N
5

1.
Check
mounting
position
for
adequate space (See caution).
2.
Place the
mounting
template
in position, then
mark
and
drill
the
mounting
holes.
3.
Connect the
wires
from
the
source
unit
to the
speaker
ensuring
the
correct
polarity
is observed.
4.
Place the
mounting
gasket
and
insert
screws
5.
Fasten screws to ensure a
water
tight seal
For
speaker
mounting
restrictions,
please
refer
to
manufacturers
CAUTION:
recommendations
for
related
navigation
equipment
6

INSTALLATION
TIPS
Any
speaker
will
perform
to its best capabilities, when
correctly
placed
in the listening area. FUSION Engineers recognise
that
unlike
a home
or
motor
vehicles installation,
there
are an
extremely
wide range of
marine
.
environments
where
speakers may
be
placed. FUSION Marine Speakers are
optimised to
perform
in the widest possible range of
mounting
locations, but
a
little
thought
and care
with
placement
will
always
be
rewarded with
better
sound.
• High frequencies are directional. Placing the speakers
low
down in
the boat
will
lose some of
this
information.
• Speakers should
be
placed to
simulate
"sound stage",
by
being
placed where you are able to
hear
both speakers in a stereo situation.
TROUBLESHOOTING
Before you contact
your
FUSION
dealer
or
service centre, FUSION requires
that you
do
some simple troubleshooting to avoid returning the product
unnecessarily.
Problem Solution
No
sound Check
all
connections
from
the
source
unit/amplifier
to the speaker
terminals
are connected
correctly
System lacks in bass Check
all
connections
from
the
source
unit/amplifier
to the speaker.
Ensure the positive
wire
from
the
source is connected to the positive
of the speaker.
System lacks in Check polarity
high frequencies Check the
bass
I
treble
control
settings
on
the source unit
Distorted sound Check-
all
wiring
-·
Check that it is not the surrounding
panels of the craft rattling.
Check connections
from
the source
unit to the speaker.

FUSI!i1l
-------
/
~~(
I
I
I
I
\
\
' /
~
---
---~
Check dimensions before cutting
r-------------------
6"
------------------~
I
I
I'
I'
I I I I
I!
I I I I I I I I
I,
I I I I I I I I
I
I I I I I I I I I
I!
I I I I I I I I
I!
I I I I I I I
II
r
r I I I I I I I I I I I I I I I I I I I I I I I 1 I
150
mm
/
*
MS-EL602
MOUNTING TEMPLATE
/
I
I
)