FWE EV303084-NA-BLK User manual

Charging the lights:
Front.
1. The battery should be fully charged before first use.
2. Undo the bezel end cap anti-clockwise (fig.1) & plug in
the micro USB cable provided, then connect to a USB
port (fig.2)
3. The power button will emit a red light to indicate that
the light is charging.
4. If the power button flashes whilst charging this means
that an error has occurred, remove & re-insert the USB
cable and begin the recharging process again.
5. The battery charges to 80% after approx. 5 hours, the
power button will go blue when the light is fully charged.
6. Disconnect the light from the charging source once fully
charged, replace the end cap & firmly tighten to ensure a
waterproof seal.
7. BATTERY INDICATOR - when the light is off, press and hold the
power button for 3 secs to enter battery indicator mode. 10 flashes
means the light is fully charged, 1 flash means empty. To exit out of
battery indicator mode, double tap the power button.
Rear.
1. The battery should be fully charged before first use.
2. Unplug the rubber cover on the back of the light (fig.3) &
plug in the USB cable provided, then connect to a USB port
(fig.4).
3. A steady green light will be ommitted from the lens whilst
charging, once the light is fully charged a red LED will flash.
4. The USB cable should be removed from the light and the
rubber cover replaced securely to prevent water ingress.
- Charging & burn times are approximate values & will vary
dependent on environment and charging source.
- During use the power button will emit a red light when there
is below 20% battery life left.
- Do not allow the light to completely lose charge as this will
greatly reduce the number of recharge cycles and reduce the life
span of the battery.
USB RECHARGEABLE LIGHT SET
450 LUMENS FRONT / 50 LUMENS REAR
(fig.4)
Ø19~Ø32
Rear.
Position the light at the required height on your seat
post, attach the strap to the hook with the bulge first
and then pull the strap around the seat post and locate
securely on the opposite hook.
(fig.2)
(fig.1)
Installing the light to your bike:
1. Position the cradle mount on to your handlebars with the shorter hook facing forward, locate the rubber
strap on to the front hook and whilst stretching the rubber strap pull it under the bar and locate on to the
longer hook at the back of the mount.
2. Once the mount is securely in place on the bars you can then install the light in to the cradle by pushing
down until it is firmly engaged.
Remove
Install
Front hook(short) Back hook (long) Strap
Ø19~Ø32

Instructions:
The battery can be fully charged & discharged approx. 500 times, the runtime
will progressively reduce over this period.
Battery life will vary dependent on the conditions in which it is used & can
result in approx. +/- 15% of the suggested run time.
The light should be fully charged prior to long periods of non-use, & to
prevent damage to the battery it should be checked every 1-2 months &
fully recharged every six months during non-use.
Store in a cool, dry place.
Never leave the light unattended whilst charging.
Allow the light to cool to ambient room temperatures prior to charging.
If the light becomes hot or starts to smoke during charging unplug from the
power supply immediately.
Do not look directly in to the light beam, or shine directly in to the eyes of other people.
This light is waterproof to grade IP65 under normal conditions of use, however it is not
designed to be fully submerged in water.
This light contains components that must be recycled as per EU directive
2002/96/EC & must not be disposed of as unsorted municipal waste.
Keep the light out of the reach of children, if any part of the light is swallowed
please seek immediate medical attention.
Warranty:
FWE lights have a warranty period of one year from original date of purchase.
If the product fails due to normal use we will replace at no charge, proof of purchase
is required.
If you experience any problems with this product please visit your nearest store, alternatively you
can email us at [e-mail] or call our contact centre team on [phone]
Turning on and changing light modes:
Front.
Double tap the power button to turn on. Single tap to scroll between modes as shown below.
Press and hold the power button for 3-5 seconds to turn off.
For your own safety do not operate the light whilst riding
Specification:
Front light.
Size: 105 x 27 x 27 mm
Weight: Approx. 105g
LED: 1 x Cree T6
Max LED Output: 450 Lumen output
Battery: Rechargeable lithium-ion
Bracket: Ø19-Ø32mm with 1 rubber pad
Standard charge time: Approx. 4-6 hours (using USB)
Accessories: Micro USB cable
Rear light.
Size: 45 x 28 x 28mm
Weight: Approx. 35g
LED output: 50 Lumens
Battery: Rechargeable Lithium-ion
Bracket: Ø19-Ø32mm with 1 rubber pad
Charge time: Approx 2 hours (using USB)
Accessories: Micro USB cable
Rear.
1. Double tap the lens to turn on.
2. Press the lens again to switch between
modes as shown (fig.1).
3. Press and hold to turn off
Press the lens to switch on and cycle between modes
Constant
4 hrs
Slow Flash
20 hrs
Fast Flash
20 hrs Off
Pulse
20 hrs
(fig.1)
High
1.5 hrs
Medium
3 hrs
Low
6 hrs
Flashing
12 hrs
Press & hold
to turn Off
Power button