FXLuminaire A-CT4 User manual
INSTALL NOTE: A-CT4
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
1. Caution and Safety Instructions
• Qualied personnel must install and/or service
this product in a manner consistent with its
intended use and in compliance with the
National Electrical Code, Canadian Electrical Code,
and/or all local and provincial codes.
• Follow all product label information and
installation instructions.
• Turn o power at the fuse or circuit breaker
before installation or servicing.
• The use of damaged components may cause an
unsafe condition and void the product warranty.
• Do not block light emanating from this product in
whole or part.
• Never operate the xture with a missing or
damaged lens. Clean the lens on a regular basis.
• The entire xture may become extremely
hot. Do not touch the hot lens or xture body.
Do not touch the light source at any time.
• Keep all O-rings and sealing surfaces clean during
installation and servicing; failure to do this may
lead to premature failure of the product.
3YJ8
Tools Needed:
• Installation: ⁄", ⁄ ", and ⁄" Allen keys
• Servicing: ⁄" Allen key and #1 Phillips
screwdriver
5.3"(133 mm)
8.5" (216 mm)
4" (102mm)
6.8" (171 mm)
67
IP
2. Product Information
• This product is suitable for mounting at grade level.
INSTALL NOTE: A-CT4
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
3. Product Installation
1. Secure the driver housing in-ground in
accordance with local codes and regulations.
2. Connect conduit or cable runs to the bottom of
the driver housing with couplings (⁄"-14 NPT,
provided by others). Use the provided ½"-14
NPT plug for unused conduit openings.
3. Add the installation cover onto the driver
housing with the provided fasteners to prevent
dirt and debris from entering the driver housing.
4. To complete the installation, attach the xture
to the driver housing faceplate. Connect the
driver wiring (provided with the xture) to the
xture using the wiring diagram and approved
wire connectors.
5. Use double-sided tape and a zip tie to secure
the driver to the driver mounting tab.
6. Tighten the 8-32 x ½" (13 mm) setscrew using
a ⁄" Allen key to lock the rotational position of
the xture to the driver housing faceplate.
7. Seal the driver housing compartment using the
provided gasket and fasteners (10-24 x ½" (13
mm) screw) with a ⁄" Allen key.
Driver Housing
Driver Housing Faceplate
Diagrams
Driver Mounting Tab
Driver
INSTALL NOTE: A-CT4
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
3. Product Installation (continued)
Wiring Chart
BlackLine/Hot/Switching
WhiteCommon
Green (via stud or
green lead)
Ground
Gray*0-10V (-)
Purple*0-10V (+)
FIXTURE
BUILDING
Standard Voltage (SV) Universal Voltage (UV) High Voltage (HV)
Input Power 120V/60Hz 110V to 277V/60Hz 220V to 240V/50Hz
Dimming Phase 0-10V 0-10V
Number of Wires 3 5 5
Black, White, Green Black, White, Green,
Purple, Gray
Brown, Blue, Green/Yellow,
Black, Gray
*For use with 0-10V driver only
Diagrams
Power Requirements
⁄ " Allen key
Upon installation, use a ⁄ " Allen key to adjust the
angle of the xture.
Gray Black
White
Purple Green
INSTALL NOTE: A-CT4
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
4. Repair/Replacement Instructions
• Standard Optics (20º, 40º, and 60º)
1. Remove the cap by unfastening the 6-32 x ⁄"
(13 mm) screw using a ⁄" Allen key. Then li
the cap outward. Avoid using metal tools while
liing the cap to protect the power coat nish.
2. Twist the reector optic counterclockwise and
pull outward to remove.
3. Unfasten the three LED module screws using a
Phillips #1 screwdriver. Remove the reector
adapter ring and LED module.
FX-296-IN 4/20
INSTALL NOTE: A-CT4
LANDSCAPE & ARCHITECTURAL LIGHTING | Learn more. Visit fxl.com
4. Warranty
STATEMENT OF LIMITED WARRANTY
Hunter Industries Incorporated (“Hunter”) warrants FX Luminaire Line-Voltage Series lighting products to be free of defects in
materials or workmanship under normal use for a period of ve (5) years from the date of invoice. If a defect in a FX Luminaire product
is discovered during the applicable warranty period, Hunter will repair or replace, at its option, the product or the defective part. This
limited warranty does not extend to repairs, adjustments, or replacement of FX Luminaire products or parts resulting from misuse,
negligence, alteration, modication, tampering, or improper installation and/or maintenance of the product. This warranty extends
only to the original installer of the product. If a defect arises in a FX Luminaire product or part during the warranty period, contact the
local authorized manufacturer’s representative. Hunter’s obligation to repair or replace its products as set forth above is the sole and
exclusive warranty set forth by Hunter. There are no other warranties, expressed or implied, including warranties of merchantability
and tness for a particular purpose. Hunter will not be liable to distributor or any other party in strict liability, tort, contract, or any other
manner for damages caused or claimed to be caused as a result of any design or defect in FX Luminaire products, or for any special,
incidental, consequential, or exemplary damages or any nature, including without limitation lost business or prots. Notwithstanding
the foregoing, if for any reason Hunter is found to be liable, in no event shall Hunter’s liability exceed the price of the product which gives
rise to the claim, loss, or damage.
If you have any questions concerning the warranty or its application, please write to:
Customer Service Department
FX Luminaire
1940 Diamond Street
San Marcos, CA 92078 USA
Table of contents
Other FXLuminaire Lantern manuals
