G-WEIKE G1 User manual

Table Of Contents
01 List of product accessories (standard/optional)
02 Key/indicator description
03 Quick Installation Instructions
04 Product specification
05 Use safety guidelines
06 Precautions
01

01. List of product accessories
Beam
E
Transmission
shaft
F
Front Frame
A
Left Frame
B
Right Frame
C
Rear Frame
D
02

Other accessories
Laser Source USB Cable
Extended axis Honeycomb TraySafety shield
Risers Power Adapter
and Power Cord
G
Optional
H
Countersunk
screws M4*8
Countersunk
screws M3*8
Countersunk
screws M4*25
Circlip Plier Round screws
M4*10
Fixed Focus
Block
Safety goggles Wrench Screw Cable Tie
Package
Quick Guide
/Instructions
03

04
02. Keys and Indicators Instructions
Laser souce
Indicator light
Focus lever
Air nozzle adapter
Smoke exhaust hole
Power interface
Emergency
stop button
USB interface
Power switch
Extended
shaft interface

05
03. Quick Installation Instructions
3-1 Assembling GWEIKE G1 Blu-ray platform
Assemble the four side baffles together, and align the power switch, power
port, and USB port with the openings on the baffle.
A
A
B
B
C
C
D
D

06
Assemble the front frame, left frame, right frame and back frame as shown in
the figure. Install 8 M3*8 screws on the upper and lower sides of the front frame
and 2 M3*8 screws on the back frame with a hex wrench, and then install 6 M4*8
screws and 2 M4*25 adjusting screws on the back frame.
*10
*6

07
Use M4*25 screws to secure the synchronous belt wheel
M4*25 Screws are used to adjust the tightness of the belt. Please do not tight-
en them too much to prevent breaking.
*2

08
How to install risers
Take out the four groups of risers, unscrew the bottom risers, remove the
rubber plug on the risers, install the four risers on the machine with four
M4X10 screws, and then install the rubber plug.
*4

09
Install optical shafts
Fix the optical shaft on the bearing through the conveyor belt. Note that the
conveyor belt needs to be covered on the idler wheel of the optical shaft.
Note: If the optical shaft cannot pass through the belt during installation, it
may be because the belt is too tight. The tightness of the belt can be adjusted
by screws.

10
Slide the coupling to the junction of the optical shaft and the motor shaft.
Note: When the coupling slides to the intersection of the optical shaft and the
motor shaft, do not cling to the motor, leaving a little space between the motor
and the coupling, otherwise the rotation of the coupling will be hindered, affect-
ing the movement of the laser on the y axis

11
Tighten the two screws on the coupling

12
Mounting beam
Use a hex wrench to install the four M4*8 screws on the left and right sides
of the beam, and install one M4*25 adjusting screw.
Note: M4*25 Screws are used to adjust the tightness of the belt. Please do
not tighten them too much to prevent breaking.
*4
*1

13
Loosen the two top posts on the nose
slide, and then install the laser head on
the nose slide from top to bottom.
Slide the laser head down to the appro-
priate position, and then tighten the
screws on the right hand.
Insert the power supply cable connec-
tor of the laser head into the laser
terminal port.
Insert the gas pipe from the air pump
into the gas pipe interface of the laser.

14
Complete the connection
Insert the connectors of the laser, motor and limit switch cables into the cor-
responding interfaces of the motherboard according to the corresponding
colors of the terminals

15
Use cable ties to secure the cables.

16
The machine can be raised by hand twisting the plastic foot pad set.
The roller rotary (optional) can be connected to the rotating shaft terminal of
the machine board card (blue) through the connecting wire

17
3-2Basic instruction
Adjust conveyor belt tightness
Adjust conveyor belt tightness
Tips: Please try to keep the tightness of the left and right baffle conveyor belts
consistent to ensure proper cutting and engraving.
Tighten the
screw clockwise
Loosen the screw
counterclockwise

18
Place the focal block
under the laser.
Loosen the hand screw
on the other side and
slide the laser up and
down so that the focus
block is attached to the
laser on the top and the
cutting material on the
bottom.
After determining the
position, tighten
Tighten the screws and
remove the focal block.
How to adjust the focal length?

19
How to connect Lightburn?
1. How to connect
(1) Lightburn software is recommended for use with G1. (Note:
Lightburn software needs to be purchased.)
(2) Items needed for connection.
(3) Connect the USB cable to the computer and connect the
other end of the USB to the machine.
2. Settings in Lightburn
(1) Open Lightburn. If this is the first time you have opened Lightburn, use the software to automati-
cally pop up the following Settings. If you have opened Lightburn before, click on the device in the
lower left corner to set the Settings.