GADGETMONSTER GDM-1003 User manual
SMART MUG
GDM-1003
2
DAN
Sikkerhed instruktioner
1. Du må ikke selv adskille eller modicere dette produkt.
2. Opladeren må ikke komme i kontakt med vand og andre væsker.
3. Før du rengør opladeren, skal du først tage stikket ud af stikkontak-
ten.
4. Velegnet til omgivelsestemperaturer på 0-45 °C.
5. Anbring ikke fremmedlegemer som metaller, mønter og nøgler,
eller magnetiske materialer såsom bankkort på opladeren.
6. Kruset må kun vaskes i hånden, ikke i opvaskemaskine.
7. Kruset må ikke placeres i mikrobølgeovnen eller ovnen.
8. Advarsel! Opladebasen bliver varm med eller uden væske.
Brug
Krusets bund er lavet af specielle materialer. Kruset opvarmes ved
elektromagnetisk induktion. Almindelige krus er ikke kompatible og
kan ikke opvarmes.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Til brug med krus: Anbring kruset i midten af opladeren. LED blinker,
når kruset er placeret korrekt.
Opladeren skifter automatisk til standby tilstand efter 8 timers brug af
holde varm funktionen.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Til opladning: Placer telefonen i midten af opladeren. LED blinker når
telefonen er placeret korrekt.
Specikation
Varme effekt: 18W
Varme metode: trådløs induktionsopvarmning
Krus størrelse: Ca. 350 ml.
3
Holde varm funktion: Omkring 55°C
LED indikation
LED blinker tre gange = opladeren er tændt og opvarmer kruset.
LED er slukket = standby tilstand eller ikke tændt.
LED blinker langsomt = opvarmning eller opladning.
LED blinker hurtigt = Der er noget galt. Dårlig placering eller frem-
medlegeme registreret.
Pleje og rengøring
1. Aftør opladeren og kablet med en tør klud. Må ikke komme i kon-
takt med vand og andre væsker.
2. Vask kruset I hånden, må ikke komme I opvasker.
3. Kruset kan tørres og desinceres op til 150°C, men det kan ikke
placeres i mikrobølgeovnen eller i ovnen.
Fejlnding
Problem
Ingen strøm.
Mulige løsninger
Stikkontakten fungerer muligvis ikke. Prøv en anden stikkontakt.
Opladeren, strømadapteren (medfølger ikke) eller kablet er ikke
tilsluttet eller ødelagt. Tilslut dem igen eller udskift de ødelagte.
Der er noget galt med opladeren, kontakt forhandleren.
Problem
LED blinker hurtigt.
Mulige løsninger
Dårlig placering. Prøv at placere anerledes.
Kruset er opvarmet i over 8 timer. Fjern kruset.
4
DEU
Sicherheitshinweise
1. Demontieren oder modizieren Sie dieses Produkt nicht selbst.
2. Halten Sie das Ladegerät von Wasser und anderen Flüssigkeiten
fern.
3. Vor dem Reinigen des Ladegeräts trennen Sie es zuerst von der
Stromquelle.
4. Geeignet für Umgebungstemperaturen bei 0-45 °C.
5. Legen Sie keine Fremdkörper wie Metalle, Münzen und Schlüssel
oder magnetische Materialien wie Bankkarten auf das Ladegerät.
6. Der Becher darf nur von Hand gewaschen werden, nicht für die
Spülmaschine.
7. Der Becher darf nicht in die Mikrowelle oder in den Ofen gestellt
werden.
8. Achtung! Die Ladebasis wird mit oder ohne Flüssigkeit heiß.
Verwendung
Der Boden des Bechers besteht aus speziellen Materialien. Der Be-
cher wird durch elektromagnetische Induktion erhitzt. Gewöhnliche
Becher sind nicht kompatibel und können nicht erhitzt werden.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Zur Verwendung mit Bechern: Stellen Sie den Becher in die Mitte des
Ladegeräts. Die LED bestätigt durch Blinken.
Das Ladegerät wechselt nach 8 Stunden mit der Warmhaltefunktion
automatisch in den Standby-Modus.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Zum Auaden: Stellen Sie das Telefon in die Mitte des Ladegeräts.
Die LED bestätigt durch Blinken.
5
Spezikation
Wärmeeffekt: 18W
Heizmethode: Drahtlose Induktionsheizung
Bechergröße: ca. 350 ml
Warm halten: ca. 55°C
LED-Status
Die LED blinkt dreimal = das Ladegerät ist eingeschaltet und heizt
den Becher auf.
Die LED ist ausgeschaltet = Standby-Modus oder nicht eingeschaltet.
Die LED blinkt langsam = Heiz- oder Ladevorgang .
Die LED blinkt schnell = Etwas Falsches. Schlechte Platzierung oder
Fremdkörper erkannt.
Pege und Reinigung
1. Wischen Sie das Ladegerät und das Kabel mit einem trockenen
Tuch ab. Von Wasser und anderen Flüssigkeiten fernhalten.
2. Reinigen Sie den Becher manuell. Der Becher ist nicht spülmaschi-
nenfest.
3. Der Becher kann in bis zu 150 °C getrocknet und desinziert wer-
den, er kann jedoch nicht in die Mikrowelle oder in den Ofen gestellt
werden.
Fehlerbehebung
Problem
Kein Strom.
Mögliche Lösungen
Die Steckdose funktioniert nicht. Versuchen Sie es mit einer anderen
Steckdose.
Das Ladegerät, der Netzadapter (nicht im Lieferumfang enthalten)
oder das Kabel sind nicht angeschlossen oder defekt. Schließen Sie
sie wieder an oder ersetzen Sie die defekten Kabel.
Mit dem Ladekreis stimmt etwas nicht. Wenden Sie sich an den
Händler.
Problem
LED blinkt schnell.
Mögliche Lösungen
Schlechte Platzierung. Versuchen Sie es mit einer anderen Platzie-
rung in der Mitte des Ladegeräts.
Der Becher wurde über 8 Stunden erhitzt. Entfernen Sie den Becher.
6
ENG
Safety instructions
1. Do not disassemble or modify this product yourself.
2. Keep the charger away from water and other liquids.
3. Before cleaning the charger, unplug it from power rst.
4. Suitable for ambient temperatures at 0-45°C.
5. Do not place foreign objects such as metals, coins and keys or
magnetic materials such as bank cards on the charger.
6. The mug must only be hand washed, not for dishwasher.
7. The mug must not be placed in the microwave or the oven.
8. Warning! The charge base gets hot with or without liquid.
Use
The bottom of the mug is made of special materials. The mug is hea-
ted by electromagnetic induction. Ordinary mugs are not compati-
ble and cannot be heated.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
For use with mug: place the mug in the center of the charger. The
LED conrms by ashing.
The charger automatically enters standby mode after 8 hours of
using the keep warm function.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
For charging: place the phone in the center of the charger. The LED
conrms by ashing.
Specication
Heat effect: 18W
Heating method: wireless induction heating
Mug size: about 350 ml
Keep warm: about 55°C
7
LED status
The LED ashes three times = the charger is powered on and heating
the mug.
The LED is turned off = standby mode or not powered on.
The LED is ashing slowly = heating or charging.
The LED is ashing fast = Something is wrong. Bad placement or
foreign object detected.
Care and cleaning
1. Wipe the charger and cable with a dry cloth. Keep away from
water and other liquids.
2. Clean the mug manually, the mug is not dishwasher safe.
3. The mug can be dried and disinfected in up to 150°C, but it can-
not be placed in the microwave oven or in the oven.
Troubleshooting
Problem
No power.
Possible solutions
The power outlet is not working. Try another power outlet.
The charger, the power adapter (not included) or the cable is not
connected or broken. Reconnect them or replace the broken ones.
Something is wrong with the charging circuit, contact the retailer.
Problem
LED is ashing fast.
Possible solutions
Bad placement. Try other placing in the center of the charger.
The mug has been heated for over 8 hours. Remove the mug.
8
EST
Ohutusjuhised
1. Ärge seda toodet ise demonteerige ega muutke.
2. Hoidke laadija eemal veest ja muudest vedelikest.
3. Eemaldage laadija enne puhastamist vooluvõrgust.
4. Sobib keskkonna temperatuuridele 0-45 °C.
5. Ärge asetage laadijale võõrkehasid, nagu metallid, mündid või
magneetuvad materjalid, nagu pangakaardid.
6. Kruusi tohib pesta ainult käsitsi, mitte nõudepesumasinas.
7. Kruusi ei tohi asetada mikrolaineahju ega ahju.
8. Hoiatus! Laadimisalus muutub nii vedelikuga kui ilma selleta kuu-
maks.
Kasutamine
Kruusi põhi on valmistatud spetsiaalsetest materjalidest. Kruusi soo-
jendatakse elektromagnetilise induktsiooni teel. Tavalised kruusid ei
ole ühilduvad ja neid ei saa soojendada.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Kasutamiseks kruusiga: asetage kruus laadija keskele. Valgusdiood
kinnitab seda vilkudes.
Pärast 8 tunni pikkust soojana hoidmise funktsiooni kasutamist läheb
laadija automaatselt ooterežiimi.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Laadimiseks: asetage telefon laadija keskele. Valgusdiood kinnitab
seda vilkudes.
Tehnilised andmed
Soojendustoime: 18 W
Soojendusmeetod: juhtmevaba induktsioonsoojendus
Kruusi suurus: umbes 350 ml
9
Soojana hoidmine: umbes 55°C
Valgusdioodi olek
Valgusdiood vilgub kolm korda = laadija on sisse lülitatud ja soojen-
dab kruusi.
Valgusdiood on välja lülitatud = ooterežiim või sisse lülitamata.
Valgusdiood vilgub aeglaselt = soojendamine või laadimine.
Valgusdiood vilgub kiiresti = midagi on valesti. Tuvastatud halb ase-
tus või võõrkeha.
Hooldus ja puhastamine
1. Pühkige laadijat ja kaablit kuiva lapiga. Hoidke see eemal veest ja
muudest vedelikest.
2. Puhastage kruusi käsitsi, kruus ei ole pestav nõudepesumasinas.
3. Kruusi saab kuivatada ja desintseerida kuni 150°C juures, kuid
seda ei tohi asetada mikrolaineahju ega ahju.
Tõrkeotsing
Probleem
Toide puudub.
Võimalikud lahendused
Pistikupesa ei tööta. Proovige teist pistikupesa.
Laadija, toiteadapter (pole kaasas) või kaabel ei ole ühendatud või
on katki. Ühendage need uuesti või asendage katkised.
Laadimise vooluringiga on midagi valesti, pöörduge müüja poole.
Probleem
Valgusdiood vilgub kiiresti.
Võimalikud lahendused
Halb asetus. Proovige muud asetust laadija keskel.
Kruusi on soojendatud üle 8 tunni. Eemaldage kruus.
10
FIN
Turvallisuusohjeet
1. Älä pura tai muokkaa tätä tuotetta itse.
2. Pidä Laturi kaukana vedestä ja muista nesteistä.
3. Ennen kuin puhdistat laturin, irrota se sähköstä ensin.
4. Soveltuvat ympäristön lämpötiloihin 0-45 ° C: ssa.
5. Ulkomaisia esineitä, kuten metalleja, metallirahoja ja avaimia tai
magneettisia materiaaleja, kuten pankkikortteja, ei saa sijoittaa
latauslaitteeseen.
6. Muki on pestävä käsin, ei tiskikoneelle.
7. Mukia ei saa laittaa mikroaaltouuniin eikä uuniin.
8. Varoitus! Latausalusta kuumenee nesteen kanssa tai ilman.
Käyttää
Mukin pohja on tehty erikoismateriaaleista. Mukia lämmitetään säh-
kömagneettisella induktiolla. Tavalliset mukit eivät ole yhteensopivia,
eikä niitä voi lämmittää.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Mukissa käytettäväksi: muki asetetaan laturin keskelle. LED vahvistaa
vilkkumalla.Laturi siirtyy automaattisesti valmiustilaan kahdeksan
tunnin kuluttua pysyvien lämmitystoiminnon käyttämisestä.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Latauksesta: Laita puhelin laturin keskelle. LED vahvistaa vilkkumalla.
Määrittely
Lämpövaikutus: 18W
Lämmitysmenetelmä: langaton induktiolämmitys
Mukien koko: noin 350 ml
Pysyttele lämpimänä: noin 553
LED-tila
11
LED-välähdykset kolme kertaa = laturi on päällä ja muki kuumenne-
taan.
LED on sammutettu = valmiustila tai se ei ole kytketty päälle.
LED vilkkuu hitaasti = lämpö tai lataus.
LED vilkkuu nopeasti. jokin on vialla. Huono sijainti tai vieras esine
havaittu.
Hoito ja siivous
1. Pyyhi laturi ja kaapeli kuivalla kankaalla. Pysy kaukana vedestä ja
muista nesteistä.
2. Pese muki käsin, niin muki ei ole astianpesukoneen turvallinen.
3. Muki voidaan kuivata ja desinoida 150 astiaan asti, mutta sitä ei
voi laittaa mikroaaltouuniin eikä uuniin.
Vianmääritys
Ongelma
Ei virtaa.
Mahdolliset ratkaisut
Virtajohto ei toimi. Kokeile toista virtajohtoa.
Latauslaite, tehonsäädin (ei sisälly) tai kaapeli ei ole kytkettynä tai
poikki. Yhdistä ne uudelleen tai korvaa rikkinäiset.
Virtapiirissä on jotain vikaa.ota yhteyttä vähittäismyyjään.
Ongelma
LED vilkkuu nopeasti.
Mahdolliset ratkaisut
Huono paikka. Kokeile toista paikkaa laturin keskellä.
Mukia on lämmitetty yli kahdeksan tuntia. Ota muki pois.
12
FRA
Instructions de sécurité
1. Ne démontez pas et ne modiez pas ce produit vous-même.
2. Tenez le chargeur éloigné de l’eau et d’autres liquides.
3. Avant de nettoyer le chargeur, débranchez-le d’abord de l’ali-
mentation.
4. Convient pour des températures ambiantes de 0 à 45° C.
5. Ne placez pas d’objets étrangers tels que des métaux, des pièces
de monnaie et des clés ou des matériaux magnétiques tels que des
cartes bancaires sur le chargeur.
6. La tasse ne doit être lavée qu’à la main, pas au lave-vaisselle.
7. La tasse ne doit pas être placée au micro-ondes ou au four.
8. Avertissement ! Le socle de charge devient chaud avec ou sans
liquide.
Utilisation
Le fond de la tasse est fait de matériaux spéciaux. La tasse est
chauffée par induction électromagnétique. Les tasses ordinaires ne
sont pas compatibles et ne peuvent pas être chauffées.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Pour une utilisation avec une tasse : placez la tasse au centre du
chargeur. La LED conrme en clignotant.
Le chargeur entre automatiquement en mode veille après 8 heures
d’utilisation de la fonction de maintien au chaud.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Pour charger : placez le téléphone au centre du chargeur. La LED
conrme en clignotant.
13
Spécications
Effet de chaleur : 18 W
Méthode de chauffage : chauffage par induction sans l
Taille de la tasse : environ 350 ml
Maintien au chaud : environ 55°C
État de la LED
La LED clignote trois fois = le chargeur est allumé et chauffe la tasse.
Le voyant est éteint = mode veille ou non allumé.
La LED clignote lentement = chauffage ou charge.
La LED clignote rapidement = Il y a un problème. Mauvais place-
ment ou objet étranger détecté.
Entretien et nettoyage
1. Essuyez le chargeur et le câble avec un chiffon sec. Tenir à l’écart
de l’eau et d’autres liquides.
2. Nettoyez la tasse manuellement, la tasse ne va pas au lave-vais-
selle.
3. La tasse peut être séchée et désinfectée jusqu’à 150 °C, mais elle
ne peut pas être placée dans un four à micro-ondes ou dans un four
traditionnel.
Dépannage
Problème
Pas d’alimentation
Solutions possibles
La prise de courant ne fonctionne pas. Essayez une autre prise de
courant.
Le chargeur, l’adaptateur secteur (non inclus) ou le câble n’est pas
connecté ou cassé. Reconnectez-les ou remplacez les items cassés.
Quelque chose ne va pas avec le circuit de charge, contactez le
revendeur.
Problème
La LED clignote rapidement.
Solutions possibles
Mauvais placement. Essayez un autre emplacement au centre du
chargeur.
La tasse a été chauffée pendant plus de 8 heures. Retirez la tasse.
14
HUN
Biztonsági utasítások
1. Ne próbálja meg a terméket saját maga szétszerelni vagy mó-
dosítani.
2. A töltőt tartsa víztől és más folyadékoktól távol.
3. A töltőt a tisztítása előtt csatlakoztassa le a tápforrásról.
4. A töltőt 0–45 °C környezeti hőmérsékleten használja.
5. Ne helyezzen idegen anyagokat, például fémtárgyakat, pén-
zérméket, kulcsokat vagy mágneses anyagokat, például bankkár-
tyákat a töltőre.
6. A bögrét csak kézzel mossa el. Mosogatógépben nem tisztítható.
7. Ne tegye a bögrét mikrohullámú, illetve hagyományos sütőbe.
8. Figyelmeztetés! A töltőalj folyadékkal és folyadék nélkül is fel-
forrósodik.
Használat
A bögre alja különleges anyagokból készült. A bögrét a töltő
elektromágneses indukcióval melegíti. A szokványos bögrék nem
kompatibilisek a töltővel, ezért azok nem melegíthetők rajta.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Bögrével való használathoz: helyezze a bögrét a töltő közepére. Ezt
a LED villogással igazolja vissza.
A töltő automatikusan készenléti üzemmódba lép, ha a melegen
tartó funkciót 8 óránál hosszabb ideig használja.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Töltéshez: helyezze a telefont a töltő közepére. Ezt a LED villogással
igazolja vissza.
15
Műszaki adatok
Melegítési teljesítmény: 18 W
Melegítési módszer: vezeték nélküli indukciós melegítés
Bögre mérete: kb. 350 ml
Melegen tartás: kb. 55°C
LED-es állapotjelzés
A LED háromszor villan = a töltő bekapcsolt, és melegíti a bögrét.
A LED nem világít = készenléti üzemmód vagy a töltő nincs bekapcs-
olva.
A LED lassan villog = melegítés vagy töltés.
A LED gyorsan villog = hiba lépett fel. Hibásan helyezte el a bögrét/
telefont a töltőn, vagy a töltő idegen tárgyat észlel.
Karbantartás és tisztítás
1. Törölje le a töltőt és a kábelt egy száraz ruhával. Tartsa víztől és
más folyadékoktól távol.
2. A bögrét manuálisan tisztítsa. Mosogatógépben nem tisztítható.
3. A bögre a szárításához és a fertőtlenítéséhez 150 °C-ig hevíthető,
de mikrohullámú, illetve hagyományos sütőbe nem helyezhető.
Hibaelhárítás
Probléma
Nincs áramellátás.
Lehetséges megoldások
Hibás a tápaljzat. Próbáljon meg egy másik tápaljzatot használni.
A töltő, a tápadapter (nem tartozék) vagy a kábel nem csatlakozik
vagy hibás. Csatlakoztassa őket újra, vagy cserélje, amelyik hibás.
Hiba lépett fel a töltőáramkörben. Forduljon az értékesítőhöz.
Probléma
A LED gyorsan villog.
Lehetséges megoldások
Hibás elhelyezés. Próbálja a bögrét vagy a telefont még egyszer a
töltő közepén elhelyezni.
A bögrét több mint 8 órán át melegítette. Vegye le a bögrét a
töltőről.
16
LAV
Drošības instrukcijas
1. Nemēģiniet pats izjaukt vai pārveidot šo preci.
2. Sargājiet lādētāju no ūdens un citiem šķidrumiem.
3. Pirms lādētāja tīrīšanas vispirms atvienojiet to no strāvas.
4. Piemērots apkārtējai temperatūrai 0-45 °C
5. Nenovietojiet uz lādētāja tādus svešķermeņus kā metālu, monētas
un atslēgas vai magnētiskus materiālus, piemēram, bankas kartes.
6. Krūzi nedrīkst mazgāt trauku mazgājamā mašīnā.
7. Krūzi nedrīkst ievietot mikroviļņu krāsnī vai krāsnī.
8. Brīdinājums! Uzlādes pamatne uzkarst ar vai bez šķidruma.
Lietošana
Krūzes apakša ir izveidota no īpašiem materiāliem. Krūzi karsē elektro-
magnētiskas indukcijas rezultātā. Parastas krūzes nav saderīgas ar
lādētāju un tās nedrīkst karsēt.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Lai izmantotu krūzi: novietojiet krūzi lādētāja centrā. Apstiprinot LED
diode mirgo.
Pēc 8 stundu darbības režīmā “saglabāt siltu” lādētājs automātiski
ieslēdzas gaidstāves režīmā.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Lai uzlādētu: novietojiet tālruni lādētāja centrā. Apstiprinot LED
diode mirgo.
Specikācija
Termoiedarbība: 18W
Karsēšanas metode: bezvadu indukcijas karsēšana
Krūzes izmērs: 350 ml
Saglabāt siltu: apmēram 55 °C
17
LED statuss
LED diode mirgo trīs reizes = lādētājs ir ieslēgts un karsē krūzi.
LED diode ir izslēgta = gaidstāves režīms vai nav ieslēgts.
LED diode lēnām mirgo = karsēšana vai uzlāde.
LED ātri mirgo = Kaut kas nav kārtībā. Konstatēts slikts novietojums vai
svešķermenis.
Apkope un tīrīšana
1. Noslaukiet lādētāju un vadu ar sausu drānu. Sargājiet no ūdens un
citiem šķidrumiem.
2. Tīriet krūzi ar rokām, to nedrīkst mazgāt trauku mazgājamā mašīnā.
3. Krūzi var žāvēt un dezincēt līdz 150 °C temperatūrā, bet to ned-
rīkst ievietot mikroviļņu krāsnī vai krāsnī.
Problēmu novēršana
Problēma
Nav strāvas.
Iespējami risinājumi
Kontaktligzda nedarbojas. Izmēģiniet citu kontaktligzdu.
Lādētājs, strāvas adapteris (nav ietverts komplektā) vai vads nav sa-
vienoti vai ir sabojāti. No jauna savienojiet tos vai nomainiet bojātās
detaļas.
Kaut kas nav kārtībā ar uzlādes ķēdi, sazinieties ar izplatītāju.
Problēma
LED ātri mirgo.
Iespējami risinājumi
Slikts novietojums. Mēģiniet lādētāja centrā novietot citādi.
Krūze ir tikusi sildīta vairāk nekā 8 stundas. Noņemiet krūzi.
18
LIT
Saugos nurodymai
1. Neardykite ir neperdarinėkite šio įrenginio patys.
2. Laikykite įkroviklį atokiau nuo vandens ir kitų skysčių.
3. Prieš valydami įkroviklį pirmiausia atjunkite jį nuo elektros tinklo.
4. Įrenginį naudokite esant 0–45 °C aplinkos temperatūrai.
5. Nedėkite ant įkroviklio pašalinių objektų, tokių kaip metalai, mone-
tos ir raktai, ar magnetinių medžiagų, tokių kaip banko kortelės.
6. Puodelį plaukite tik rankomis, o ne indaplovėje.
7. Nedėkite puodelio į mikrobangų krosnelę ar orkaitę.
8. Atsargiai! Įkrovimo pagrindas įkaista su skysčiu arba be jo.
Naudojimas
Puodelio dugnas pagamintas iš specialių medžiagų. Puodelis kaitin-
amas elektromagnetine indukcija. Įprasti puodeliai nėra suderinami
su šiuo įkrovikliu ir jo pagalba negali būti šildomi.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Naudojimas su puodeliu: pastatykite puodelį įkroviklio centre. Veik-
smas patvirtinamas, jei mirksi LED.
Įkroviklis automatiškai pereina į budėjimo režimą kuomet 8 valandas
yra aktyvi „palaikyti šilumą“ funkciją.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Įkrovimui: padėkite telefoną įkroviklio centre. Veiksmas patvirtin-
amas, jei mirksi LED.
Specikacija
Kaitinimo efektas: 18 W
Kaitinimo būdas: belaidis indukcinis šildymas
Puodelio dydis: apie 350 ml
Palaikoma šiluma: apie 55 °C
19
LED būsenos
LED sumirksi tris kartus = įkroviklis įjungtas, kaitinamas puodelis.
LED išjungtos = aktyvus budėjimo režimas arba įrenginys neįjungtas.
LED lėtai mirksi = vyksta šildymas arba krovimas.
LED greitai mirksi = kažkas negerai Aptiktas netinkamas pašalinių
objektų panaudojimas.
Priežiūra ir valymas
1. Įkroviklį ir laidą valykite sausa šluoste. Laikykite jį atokiau nuo van-
dens ir kitų skysčių.
2. Valykite puodelį rankiniu būdu; jis nėra pritaikytas valymui in-
daplovėje.
3. Puodelis gali būti džiovinamas ir dezinfekuojamas iki 150 °C tempe-
ratūroje, tačiau jo negalima dėti į mikrobangų krosnelę ar orkaitę.
Problemų sprendimas
Problema
Nėra maitinimo.
Galimi sprendimai
Neveikia maitinimo lizdas. Pabandykite kitą maitinimo lizdą.
Įkroviklis, maitinimo adapteris (neįtrauktas) arba laidas nėra prijungti
arba yra nutrūkę. Iš naujo juos prijunkite arba pakeiskite sugedusius
įrenginius veikiančiais.
Kažkas negerai su įkrovimo grandine, susisiekite su pardavėju.
Problema
LED greitai mirksi.
Galimi sprendimai
Netinkama objekto pozicija. Pabandykite kitą poziciją įkroviklio
centre.
Puodelis buvo kaitinamas daugiau nei 8 valandas. Nuimkite puodelį
nuo įkroviklio.
20
NLD
Veiligheidsinstructies
1. Probeer dit product niet zelf te demonteren of aan te passen.
2. Houd de oplader uit de buurt van water en andere vloeistoffen.
3. Haal de oplader uit het stopcontact voordat u deze schoon-
maakt.
4. Geschikt bij omgevingstemperatuur van 0 tot en met 45°C.
5. Plaats geen vreemde voorwerpen zoals metalen, munten en sleu-
tels of magnetische materialen zoals bankpassen op de oplader.
6. De mok mag alleen met handen en niet in de vaatwasser worden
afgewassen.
7. De mok mag niet in de magnetron of oven worden geplaatst.
8. Let op! Het laadstation wordt heet zowel met of zonder vloeistof.
Gebruik
De onderkant van de mok is van speciale materialen gemaakt. De
mok wordt door elektromagnetische inductie verwarmd. Gewone
mokken zijn niet compatibel en kunnen niet worden verwarmd.
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Specifications
Name: Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Voor gebruik van mok: plaats de mok in het midden van de
oplader. De LED bevestigt het door te knipperen. De oplader gaat
automatisch in de stand-bymodus na 8 uur gebruik van de warm-
houdfunctie.
Specifications
Name:
Wireless Charger
Input: 12V/1.5A
Charging output: 5V/1A
9V/1.2A
12V/1.5A
Transmission distance: less than 6mm
Charging efficiency: about 80%
LED indicator Phenomenon description
The light flashes three times The wireless charger is turned on
The light is not bright Standby mode
In the state of breathing light Power transmission
Flashing lights The location is not in place or security is
activated
Applicable equipment
1. Built-in wireless charging receiver (iphone8, iphoneX, Samsung S6, etc.),
2. Equipment with a protective cover for the receiving device (iphone7 series, etc.)
Wireless mug warmer instructions
After power-on, place the matching ceramics mug in the center of the base.
Wireless charger instructions
Place the phone in the middle of the wireless charger and the breathing light flashes to the
charging state.
EnglishContent
Package Contents---------------------------------------------------------
Wireless mug warmer instructions------------------------------------
Wireless charger instructions ------------------------------------------
Specifications --------------------------------------------------------------
Care and Cleaning--------------------------------------------------------
Troubleshooting-----------------------------------------------------------
User Manual
Wireless Charger
Please read the instructions carefully before using this product! This product is
household use only.
Package Contents
1. Wireless charger
2. Adapter
3. Power cord
4. Ceramic cup
5. Ceramic cup cover
Important Safeguards
1. Do not disassemble or modify this product yourself.
2. Keep the charger and receiver away from water and other liquids.
3. To clean the charger, make sure that no power is plugged in.
4. The ambient temperature is maintained at 0-45 ° C
5. It is forbidden to place metal materials such as coins and keys or magnetic materials
such as bank cards on the charger, which will affect normal work.
6. Thecups can only be hand washed, not for microwave/dishwasher/oven.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:(1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1 2 3
LED indicator Phenomenon description
The light flashes three times The mug warmer is turned on
The light is not bright Standby mode /not powered on /not used
for more than 8hours
In the state of breathing light Heating /charging
Flashing lights The location is not in place or security is
activated
4
Note: Entering standby mode after 8 hours of heat preservation.
Note: The bottom of the mug is made of special materials. The mug is placed on the
base and heated by electromagnetic induction. The ordinary cup is not compatible
and cannot be heated.
Note: These receivers must comply with the WPCQI standard for compatibility
Note: The wireless charger is equipped with a “wireless charging and heating
adaptive switch”, which can effectively prevent metal objects or mobile phones
from being heated and further prevent damage to the mobile phone or burn the
user, and the heat preservation cup can be automatically switched to Heating
function.
Care and Cleaning
1. Wipe the adapter, data cable, and charging stand with a rag or paper towel. Never
enter the water.
2. Please clean the cup manually, do not use dishwasher.
3. The cup can be dried and disinfected in 150℃/ 302℉, but it can't be placed in a
microwave oven or heated in the oven.
Troubleshooting
Problem Possible causes What to do
No power The grid is out of power Change the power socket
No power The power cord plug is not in place Put the power cord plug in place
No power Adapter or power cord is broken Replace
No power Charging block circuit is bad Contact the dealer
Flashing light The appliance is not in place Put the appliance in place
Flashing light The cup is heated for more than 8
hours
Pick up the cup and put it back in
the cradle
5
Specifications
Name: Wireless Charger
Heating power : 18W
CUP CAPACITY: ABOUT 350ML
Keepwarm: about 50℃/ 122℉(more suitable for human drinking water )
Material: reinforced porcelain
Heating method: wireless induction heating
1
2
2
3
5
5
、 、
Om op te laden: plaats de telefoon in het midden van de oplader.
De LED bevestigt het door te knipperen.
Popular Kitchen Appliance manuals by other brands
Scarlett
Scarlett SC-JE50S18 instruction manual
Margaritaville
Margaritaville Bahamas DM0500 Series user manual
Zephyr
Zephyr Presrv PRW15C01CG Use, care and installation guide
Roccbox
Roccbox RBX1 - 2016 user manual
Gastroback
Gastroback Design Milk & Chocolate Advanced operating instructions
Zephyr
Zephyr AK1710 Use, care and installation guide
