GAL A X Y AUDIO Quick Start Guide
AS-900
Wireless Personal Monitor
Included Components
1. AS-900T x1
4. MREWD Rack Kit x1
5. Antenna x1
2. AS-900R x1
1.
2 3
Setup
1
Attach the long and short rack ears to
either side of choice using the provided
screws. Align and screw into the rack.
Single Rack Mounting (Optional)
1
7.
Optional Accessories
6. Power Supply x1
7. Quick Start Guide x1
1. EB6 Ear Bud Upgrade
3. Unlimited Receivers
can be added
2. EB10 Ear Bud Upgrade
4. EXTBNC: BNC Cable
for Front Mounting Antenna
(4 lengths available)
1. 2.
Insert the 5.5mm plug into the DC input
jack, plug the wall wart into a 120VAC
outlet.
4
Attach the antenna to the antenna jack
o
and position at a 45 angle if possible.
Input Connection (1/4"): Connect a 1/4"
cable to the transmitter’s left and right
1/4" input, connect the other end into
your signal source's left and right outputs.
Input Connection (XLR): Connect a
shielded XLR microphone cable to the
transmitter’s left and right XLR input,
connect the other end into your signal
source’s left and right outputs.
1. Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2. #2 Phillips Head
Screwdriver
What May be Needed
to Rack
(Not Included)
1. 2.
2
1
Screw one short rack ear on the left side
of the first transmitter, and one coupler
half onto the right side of the same
transmitter using the provided screws.
2
Screw one short rack ear on the right
side of the second transmitter, and one
coupler half onto the left side of the
same transmitter.
1
Operation
Press the Power button to power on
the Transmitter.
Dual Rack Mounting (Optional)
3
Align both transmitters so that the coupler
halves fit, and screw them together.
3 4
5.
5. CN-BNCPM: BNC Connector
for Front Mounting Antenna
4
Align the dual transmitters to the rack
and screw into the rack.
6.
Insert Two AA Alkaline Batteries into the
Receiver.
3.
Insert the ear buds into the receiver and
adjust the volume to a comfortable level.
4. 5.
3.
Turn the Level knob clockwise to power
on the Receiver.
2.
4.
3. EB4 Ear Buds x1
GAL A X Y AUDIO Quick Start Guide
AS-900
Wireless Personal Monitor
Included Components
1. AS-900T x1
4. MREWD Rack Kit x1
5. Antennas x1
2. AS-900R x1
1.
2 3
Setup
1
Attach the long and short rack ears to
either side of choice using the provided
screws. Align and screw into the rack.
Single Rack Mounting (Optional)
1
7.
Optional Accessories
6. Power Supply x1
7. Quick Start Guide x1
1. EB6 Ear Bud Upgrade
3. Unlimited Receivers
can be added
2. EB10 Ear Bud Upgrade
4. EXTBNC: BNC Cable
for Front Mounting Antenna
(4 lengths available)
1. 2.
Insert the 5.5mm plug into the DC input
jack, plug the wall wart into a 120VAC
outlet.
4
Attach the antenna to the antenna jack
o
and position at a 45 angle if possible.
Input Connection (1/4"): Connect a 1/4"
cable to the transmitter’s left and right
1/4" input, connect the other end into
your signal source's left and right outputs.
Input Connection (XLR): Connect a
shielded XLR microphone cable to the
transmitter’s left and right XLR input,
connect the other end into your signal
source’s left and right outputs.
1. Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2. #2 Phillips Head
Screwdriver
What May be Needed
to Rack
(Not Included)
1. 2.
2
1
Screw one short rack ear on the left side
of the first transmitter, and one coupler
half onto the right side of the same
transmitter using the provided screws.
2
Screw one short rack ear on the right
side of the second transmitter, and one
coupler half onto the left side of the
same transmitter.
1
Operation
Press the Power button to power on
the Transmitter.
Dual Rack Mounting (Optional)
3
Align both transmitters so that the coupler
halves fit, and screw them together.
3 4
5.
5. CN-BNCPM: BNC Connector
for Front Mounting Antenna
4
Align the dual transmitters to the rack
and screw into the rack.
6.
Insert Two AA Alkaline Batteries into the
Receiver.
3.
Insert the ear buds into the receiver and
adjust the volume to a comfortable level.
4. 5.
3.
Turn the Level knob clockwise to power
on the Receiver.
2.
4.
3. EB4 Ear Buds x1
