GALBIATI PRIMA User manual

AUTOCLAVE
PRIMA
GUIDE FOR QUICK
INSTALLATION

Distilledwaterout
Distilledwaterin
Usedwaterout
Overflowport
Distilledwaterout
Distilledwaterin
Usedwaterout
Overflowport
Distilledwaterout
Distilledwaterin
Usedwaterout
Overflowport
Distilledwaterout
Distilledwaterin
Usedwaterout
Overflowport
AUTOCLAVE PRIMA
1. Please unpack the Prima Autoclave.
2. Please remove
the protective film.
1 › 2 ›
4 › 5 ›
3 ›
2

PRIMA
3. Check that all accessories are present.
N. DESCRIPTION QUANTITY
A RACK (FOR TRAYS) 1 PIECE
B TRAYS 4 SET
C DRAINAGE PIPE 2 PIECES
D GASKET 1 PIECE
E INSTRUMENT FOR TRAYS 1 PIECE
F USER MANUAL 1 PIECE
G DOOR KEY FOR DOOR
REGULATION 1 PIECE
H USB KEY 1 PIECE
I SPACERS 2 PIECE
x1
x1
x2
x1
x2
A
B
C
D
F
G
E
x1
x 2I
H
x1
x2
3

4. Please place the sterilizer on a flat surface area
and raise the front-end part 3.5 cm higher
than the back-end as illustrated below:
3.5 cm
minimum
5° upwards
Figure 1
Figure 2
Figure 3
6. Please tighten the spacer
on the back end.
(Figure 2)
7. Please connect the machine
to the power supply. (Figure 3)
5. To regulate the incline of this sterilizer,
please unscrew the nut with the 17 mm key.
Please regulate the base and tighten
the nut with 17 mm. (Figure 1)
4

8. Please connect the drain pressure pipe (Connector 1)
and the used water pipe (Connector 2)
to the available exhaust system through
the specific connectors. (Figure 4)
9. Please switch on the sterilizer through
the power switch located on the bottom right
corner of the front side of the sterilizer. (Figure 5)
10. Please set up the machine as follows:
PROG. (BUTTON 3) TEST (BUTTON 1)
START (BUTTON 2)
Please remove all accessories from
the chamber before switching
the machine on.
Connector 2Connector 1
!
Figure 5
Figure 4
Used Water OutOverflow port
5

A. DATE AND TIME SETTING:
- Please turn on Setting Mode and keep pressing together to
“PROG” (Button 3) and “TEST” (Button 1) for about 8 seconds.
The following graphics will appear on the screen: (Figure 6)
- Please push PROG. (Button 3) for choosing the different
functions (YY/MM/DD and hh:mm:ss) and TEST (Button 1)
or START (Button 2) for setting the required date and time:
- Once you have set time and date, please push PROG.
(Button 3) until it appears “out” on the screen
and please push START (Button 2) to exit from
Setting Mode. (Figure 7a)
B. ENERGY-SAVING SETTING:
- Please press TEST (Button 1) for about 8 seconds and choose “POer”
function. When you choose the “POer” function, the “Heat” function
will appear on the screen. (Figure 7b)
- Please press PROG. (Button 3) and choose the “POer” function. (Figure 7c)
- Please press TEST (Button 1) for turning on (0) or off (1) the energy-saving
function. (Figure 7d)
Date and time setting Year Month Day Hour Minutes Second Exit
STEP: -1- -2- -3- -4- -5- -6- -7-
DISPLAY: 14 05 24 15 45 55 out
Temp.
Press.
Time
- i -
°C
kPa
Min.
Figure 7a
Figure 7b Figure 7c Figure 7d
Figure 6
6

C. ALTITUDE SETTING:
- Please press together START (Button 2) + TEST (Button 1)
for about 8 seconds.
- T1 function will appear on the screen (Figure 8a).
- Please press PROG. (Button 3) for 6 times until “ALT”
function appears on the screen.
- Please press TEST (Button 1) or START (Button 2)
for increasing or decreasing the altitude value***
(Figure 8b)
- Please press PROG. (Button 3) to exit from
the ALT function. (Figure 8c)
*** Discover more about it:
Visit this site http://dateandtime.info/it/citycoordinates.php?id=2988507
or download Altimetro Preciso (AR Lab) App.
D. To check the setting modes, please scroll down with PROG. button
for choosing the different functions and with TEST/START buttons
for turning them on or off:
- PRINTER: ON/OFF (Figure 9a)
- USB: ON/OFF (Figure 9b)
- DRY: 1 default setting mode (Figure 9c)
- BLUETOOTH: ON/OFF (Figure 9d)
i
Figure 8a Figure 8b Figure 8c
7

To modify these functions:
- Please press TEST (Button 1) for about 8 seconds;
- Please press PROG. (Button 3) for choosing the several functions
(PRINTER, USB, DRY, BLUETOOTH);
- Please press PROG. (Button 3) to exit from the Setting Mode
and press START (Button 2)
E. Please install the digital report program according to the technical manual.
(Pages 46-48)
F. Please switch on the machine and check all functions by choosing
the different programs.
(Please select the quick wrapped program for testing the sterilizer)
G. At the end of the cycle, please check if the report is correctly printed
and it is saved on USB.
FOR FURTHER INFORMATION ABOUT THE TECHNICAL INSTALLATION,
PLEASE READ THE TECHNICAL MANUAL ISSUED.
Via Umbria 10 20090 Segrate Milano ITALIA
[email protected]om www.galbiati.com
Figure 9a Figure 9b Figure 9c Figure 9d
!
8